BOSCH FLEXIDOME MICRO 3100I NUV-3703-F02-GOV (01) PDF Document

To operate the BOSCH FLEXIDOME MICRO 3100I NUV-3703-F02-GOV, the following system requirements are recommended:

Computer with Dual core HyperThreading processor or better.

Graphic card with performance that matches or is better than the resolution of the camera.

Windows 10 or later.

Network access.

Google Chrome, Microsoft Edge, or Mozilla Firefox.

Alternatively, application software such as Video Security Client, Bosch Video Client, or BVMS can be used.

To connect to the BOSCH FLEXIDOME MICRO 3100I NUV-3703-F02-GOV:

1. Start the web browser.

2. Enter the IP address of the device as the URL.

3. During the initial installation, confirm any security questions that show.

If a RADIUS server is used for network access control, you must configure the device before it can communicate with the network. To configure the device, connect it directly to a computer using a network cable and set the service-level password.

When setting a password for the BOSCH FLEXIDOME MICRO 3100I NUV-3703-F02-GOV, strictly obey the following conditions:

8 to 19 characters in length.

Upper and lower case letters.

Minimum of 1 digit.

Minimum of 1 special character.

The following special characters are not allowed: ‘@’, ‘&’, ‘<', '>‘, ‘:’, ‘+’

You may need to complete a hardware reset if the BOSCH FLEXIDOME MICRO 3100I NUV-3703-F02-GOV cannot be accessed, the image is frozen, or firmware updates fail. Follow these steps:

1. Apply power to the camera.

2. Find the hardware reset button on the camera block. You may need to remove the camera bubble to access it.

3. Push and hold the reset button for more than 10 seconds. The red LED indicator on the device will begin flashing to show that the hardware reset started.

4. Let the camera complete a self-check. When the self-check completes, the red LED will turn off.

5. Search again for the IP address, access the camera using the web browser, and set the initial password.

After establishing a connection, the Live page is displayed initially. To select a specific video stream:

1. On the left side of the browser, expand the Connection group if necessary.

2. Click the Stream drop-down arrow to see the options.

3. Select the stream you wish to view.

To export video from the Playback page:

1. Expand the Export group on the left side of the browser if necessary.

2. Select a track in the track list or in the search results.

3. The start and stop date and time are filled for the selected track. Change the times if necessary.

4. In the Time lapse drop-down box, select “Original” to export the video as is, or “Condensed” to export video condensed to a given output time.

5. In the Location drop-down box, select a target.

6. Click Export to save the video track.

To create a new user in the Configuration section under User Management:

1. Click Add in the section below Authentication modes.

2. In the User box, enter a User name (minimum 5, maximum 31 characters).

3. Select the appropriate Group (authorization level): “live”, “user”, “IVA configuration”, or “service”.

4. Select the Type: either “Password” (enter a new password twice) or “Certificate”.

5. Click Set to confirm and create the new user.

To synchronize the internal clock of the BOSCH FLEXIDOME MICRO 3100I NUV-3703-F02-GOV with your computer:

1. Navigate to Configuration > General > Date/Time.

2. Ensure recording is stopped before syncing.

3. Click the “Sync to PC” button to copy your computer’s system time to the camera.

In the Installer Menu under Camera configuration, you can select one of four image rotation options based on mounting position:

0°: Normal position.

90° – upright: Good for vertical scenes such as hallways.

180°: Inverted.

270° – upright: Good for vertical scenes.

Note: Upright modes change the aspect ratio (e.g., 16:9 to 9:16).

To add overlays such as camera name, logo, or time to the video image:

1. Go to Configuration > Camera > Display Stamping.

2. Configure Global configuration or individual settings for Camera name stamping, Logo stamping, Time stamping, or Alarm mode stamping.

3. Select the Position (Top, Bottom, Custom, or Off).

4. Adjust Stamping size, Text color, and Background color.

5. Click Set to apply the changes.

If automatic calibration is insufficient, use Sketch-based calibration in the Positioning menu:

1. Enter known values for tilt angle, roll angle, height, and focal length if available.

2. Select the Calculate check box for unknown values.

3. Place calibration elements on the camera image: use the vertical line tool to trace vertical objects (like door frames) and the line on ground tool for ground markings.

4. Enter the real size of the lines or angles in the corresponding boxes.

5. Adjust the position/length of the lines by dragging the nodes.

6. Verify that white lines (representing the calculated position) match the blue lines (user input).

To delete all data and recreate a valid file structure on the storage medium:

1. Go to Configuration > Recording > Storage Management.

2. Click a storage medium in the Managed storage media list to select it.

3. Click Edit below the list.

4. Click Format in the new window to delete all recordings.

5. Click OK to close the window.

6. Click Set to apply the changes.

To schedule recordings:

1. Go to Configuration > Recording > Recording Scheduler.

2. Click the profile to be assigned in the Time periods box.

3. Click a field in the table and drag the cursor across the fields to assign the profile to specific times/days.

4. Use “Select All” to fill the schedule or “No recordings” to deselect intervals.

5. Click Set to save the settings.

6. To activate, click Start to enable the recording schedule.

To update the firmware via the Maintenance page:

1. Store the firmware file on your hard disk.

2. In the Firmware section, enter the full path or click Browse to locate the file.

3. Click Upload to begin transferring the file.

4. Wait for the upload to complete. The device will reboot automatically when finished.

Notice: Do not interrupt the firmware installation or close the browser window during the process.

To block specific areas of the scene:

1. Go to Configuration > Camera > Privacy Masks.

2. Select the Pattern color (Auto, Black, Gray, White, or Custom color).

3. Select a mask number from the drop-down list and click the plus button.

4. Adjust the mask in the image by dragging nodes or double-clicking edges to add/remove nodes.

5. Check the Enabled box to activate the mask.

6. Click Set to apply.

To measure pixel coverage for identification tasks:

1. Go to Configuration > Camera > Pixel Counter.

2. Click Freeze to freeze the camera image if the object is moving.

3. Use the mouse to drag and reposition the measurement zone over the object.

4. Drag the edges of the zone to resize it.

5. The number of horizontal and vertical pixels covered by the area is displayed below the picture.

To send e-mails upon alarm events:

1. Go to Configuration > Alarm > Alarm Email.

2. Select On for “Send alarm e-mail”.

3. Enter the Mail server IP address, SMTP port, SMTP user name, and Password.

4. Select the Format (Standard with JPEG or SMS).

5. Configure Destination address and Sender address.

6. Click “Send Now” to test the configuration.

7. Click Set to apply.