BOSCH FLEXIDOME MICRO 3100I NUE-3702-F04-GOV (01) PDF Document

The recommended system requirements are:

Computer with Dual core HyperThreading processor or better.

Graphic card with performance that matches or is better than the resolution of the camera.

Windows 10 or later.

Network access.

Google Chrome, Microsoft Edge, or Mozilla Firefox.

Application software, for example, Video Security Client, Bosch Video Client or BVMS.

To establish a connection, follow these steps:

1. Start the web browser.

2. Enter the IP address of the device as the URL.

3. During the initial installation, confirm any security questions that show.

If a RADIUS server is used for network access control (802.1x authentication), you must configure the device before the device can communicate with the network. To configure the device, connect it directly to a computer using a network cable and then set the service-level password.

The device requires a strong password. Make sure the password obeys these conditions:

8 to 19 characters in length.

Upper and lower case letters.

Minimum of 1 digit.

Minimum of 1 special character.

The following special characters are not allowed: ‘@’, ‘&’, ‘<', '>‘, ‘:’, ‘+’

To view a live stream of the selected video channel:

1. On the left side of the browser, expand the Connection group if necessary.

2. Click the Stream drop-down arrow to see the options.

3. Select the stream you wish to view.

1. On the left side of the browser, expand the Export group if necessary.

2. Select a track in the track list or in the search results.

3. The start and stop date and time are filled for the selected track. If necessary, change the times.

4. In the Time lapse drop-down box, select Original, to export the recorded video as its original, or Condensed to export the recorded video condensed to the given output time.

5. In the Location drop-down box, select a target.

6. Click Export to save the video track.

To create a new user, click Add in the section below Authentication modes. In the box User, fill in the fields:

1. User name: Enter a name with a minimum of 5 and a maximum of 31 characters.

2. Group: Select the appropriate authorization level (live, user, IVA configuration, or service).

3. Type: Select either Password (enter a new password twice) or Certificate.

4. Click Set to confirm and create a new user.

Make sure that recording is stopped before synching to the PC.

1. Go to the Date/Time configuration page.

2. Enter the current time or click the Sync to PC button to copy your computer’s system time to the camera.

In the Camera > Installer Menu section, select the option that best suits the device mounting position:

0°

90° – upright

180°

270° – upright

If the device is mounted in its normal position, select 0°. The end result is shown in the Live preview.

Navigate to the Installer Menu.

Click the Enabled or Disabled check-box to switch the Camera LED on or off.

Select Auto disable to let the camera determine when the LED should be switched off. The camera LED activates when powering on the camera for the first time. The LED deactivates automatically after 5 minutes.

In the Camera configuration menu, click Defaults to restore all settings, including passwords and network settings, to their defaults. Clicking this button also clears the service-level password. Operators must reset the password before doing anything else.

1. Enter the value for tilt angle, roll angle, height, and focal length if the value is known.

2. For each value that is still unknown, select the Calculate check box, then place a calibration element on the camera image.

3. Use calibration elements to trace individual outlines of the displayed environment in the camera image:

– Click to place a vertical line across the image (e.g., door frame, lamp post).

– Click to place a line across the ground in the image (e.g., road marking).

– Click to place an angle on the ground in the image (e.g., corner of a carpet).

4. Adjust the calibration elements to the situation by entering the real size of a line or angle in the corresponding box and dragging the line or angle to the desired position.

The available profiles depend on the model resolution. For 2 MP models:

To format storage media (deletes all data and recreates file structure):

1. Click a storage medium in the Managed storage media list to select it.

2. Click Edit below the list.

3. Click Format in the new window to delete all recordings in the storage medium.

4. Click OK to close the window.

To wipe storage media (deletes all data without recreating file structure):

1. Click a storage medium in the Managed storage media list to select it.

2. Click Edit below the list.

3. Click Wipe in the new window to wipe the recordings in the storage medium.

4. Click Close to close the window.

Click Set to apply the changes.

After completing configuration, follow these steps to activate the recording schedule:

1. Go to the Recording Scheduler page.

2. Click Start to activate the recording schedule.

Note: Once activated, the Recording Profiles and the Recording Scheduler are deactivated and the configuration cannot be modified. To modify the configuration, click Stop to deactivate the recording schedule.

1. Select On for “Send alarm e-mail” to automatically send an alarm e-mail in the event of an alarm.

2. Enter the IP address of a mail server in the “Mail server IP address” field.

3. Select the appropriate SMTP port.

4. Enter a registered user name and password for the chosen mail server.

5. Select the data format of the alarm message (Standard with JPEG or SMS).

6. Enter the destination address and sender address.

7. Click Set to apply the changes.

1. First, store the firmware file on your hard disk.

2. Enter the full path for the firmware file in the field or click Browse… to locate and select the file.

3. Click Upload to begin transferring the file to the device. The progress bar allows monitoring of the transfer.

The new firmware is unpacked and the Flash memory is reprogrammed. When the upload is completed successfully, the device reboots automatically.

Notice: A factory default deletes all camera settings including passwords, network settings, and image settings.

1. Apply power to the camera.

2. Find the hardware reset button on the camera block. Remove the camera bubble to access the reset button.

3. Push and hold the reset button for more than 10 seconds. The red LED indicator on the device will begin flashing to show that the hardware reset started.

4. Let the camera complete a self-check. When the self-check completes, the red LED will turn off.

5. Search again for the IP address. Access the camera using the web browser. Set the initial password for the camera.