Free English ANKO SL24009W (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD ANKO SL24009W (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What should be done with all packaging before using the ANKO SL24009W OUTDOOR WALL LIGHT PROJECTOR?
Remove all packaging before use and dispose of safely.
How should the solar panel assembly be fixed to the ground for the ANKO SL24009W OUTDOOR WALL LIGHT PROJECTOR?
Ensure there are no pipes or mains cables immediately underneath, then fix the solar panel assembly to the ground by the anchor spike. Refer to the assembly diagram.
Where should the ANKO SL24009W OUTDOOR WALL LIGHT PROJECTOR not be positioned?
Do not position or place near barbecues, heaters, or any other direct sources of heat.
What location requirements are necessary for the solar panel of the ANKO SL24009W OUTDOOR WALL LIGHT PROJECTOR to perform optimally?
The solar panel should be located where sunlight can fall directly on the panel. Shadows from buildings, trees, walls/hedges and similar objects should be avoided if possible as these will reduce performance.
What should be avoided when selecting a location for the PIR sensor of the ANKO SL24009W OUTDOOR WALL LIGHT PROJECTOR?
Try to avoid locations where light from other sources (e.g. streetlights, floodlights etc) may affect the PIR sensor. The light stakes are designed only to illuminate in dark conditions and may not operate if light reflects on the panel.
Can the ANKO SL24009W OUTDOOR WALL LIGHT PROJECTOR be left outside in the rain?
The light set can be left outside in rain but should not be exposed to water jets or immersed. For optimum life, the solar panel should be stored indoors during extreme weather conditions (prolonged snow and frost).
How should the light set be located by inserting the spike in the ground for the ANKO SL24009W OUTDOOR WALL LIGHT PROJECTOR?
Locate light set by inserting the spike in the ground, choose a location where there is soft ground to enable the spike to be pushed in easily.
How does the solar light in the ANKO SL24009W OUTDOOR WALL LIGHT PROJECTOR function during the day and night?
The solar light consists of a solar cell, a rechargeable battery and LED lights. All these are preassembled. During the daytime, light from the sun charges up the batteries. At night, the energy stored in the batteries is used to power the light. No other power or connections are required. The length of time the light stays on is dependent on how much sunlight has been received during the day.
What action is required regarding the ON/OFF switch for the ANKO SL24009W OUTDOOR WALL LIGHT PROJECTOR?
Turn the ON/OFF switch at the bottom to “ON”.
What should be ensured when placing the light set at the desired locations for the ANKO SL24009W OUTDOOR WALL LIGHT PROJECTOR?
Ensure the cables are anchored so that they do not present a tripping hazard.
What is the best projection distance for the ANKO SL24009W OUTDOOR WALL LIGHT PROJECTOR?
Best projection distance is around 3~5 meters.
What is the intended environment for use of the ANKO SL24009W OUTDOOR WALL LIGHT PROJECTOR?
The light set is designed for use OUTDOOR ONLY.
What warning applies to children and pets regarding the ANKO SL24009W OUTDOOR WALL LIGHT PROJECTOR?
This product is not a toy, keep out of reach of children and pets.
What is a potential hazard related to small parts on the ANKO SL24009W OUTDOOR WALL LIGHT PROJECTOR?
This product has small parts, which may pose a choking hazard if detached.
Can the battery in the ANKO SL24009W OUTDOOR WALL LIGHT PROJECTOR be replaced?
The battery is non-replaceable. DO NOT attempt to replace it.
Can the bulbs in the ANKO SL24009W OUTDOOR WALL LIGHT PROJECTOR be replaced?
The light set is constructed with non-replaceable bulbs. DO NOT attempt to replace any of the bulbs in the light set.
What should be kept away from the ANKO SL24009W OUTDOOR WALL LIGHT PROJECTOR?
Keep away from fire and sources of heat.
What should not be allowed concerning the sharp end point of the ground stake for the ANKO SL24009W OUTDOOR WALL LIGHT PROJECTOR?
The end point of the ground stake is sharp. Please do not allow children to play with the anchor spike.
What should not be allowed to come into contact with the batteries or wiring of the ANKO SL24009W OUTDOOR WALL LIGHT PROJECTOR?
Do not allow water to come into contact with the batteries or wiring.
Is condensation forming inside the unit or solar panel of the ANKO SL24009W OUTDOOR WALL LIGHT PROJECTOR in cold conditions a concern?
Some condensation may form inside the unit or solar panel in cold conditions. This is normal and can be ignored.
What are the contents included with the ANKO SL24009W OUTDOOR WALL LIGHT PROJECTOR?
The contents include the following:
- projector x 1
- projector stake x 1
- solar panel pole x 1
- solar panel stake x 1
How is the ANKO SL24009W OUTDOOR WALL LIGHT PROJECTOR assembled according to Step 1 of the Assembly Diagram?
Step 1 involves connecting the cable from the projector assembly (labeled 1) to the solar panel assembly (labeled 2).
How is the ANKO SL24009W OUTDOOR WALL LIGHT PROJECTOR assembled according to Step 2 of the Assembly Diagram?
Step 2 shows the final ground mounting of the components:
1. The solar panel assembly is mounted onto the solar panel pole (labeled 1).
2. The solar panel pole is inserted into the solar panel stake (labeled 2).
3. The complete solar panel setup is shown inserted into the ground (labeled 3).
CLICK HERE TO DOWNLOAD ANKO SL24009W (01) PDF DOCUMENT