ANKO HEG22AC (01) PDF Document

Keep the appliance out of reach of young children.

Ensure children and babies do not play with plastic bags or any packaging materials.

Do not disassemble the appliance as there are no user-serviceable parts inside.

Ensure that the appliance does not get wet (water splashes, etc.) and do not use it with wet hands.

Do not immerse the appliance in water or other liquids or use it near sinks, baths, or showers.

Always operate the appliance from a power source of the same voltage, frequency, and rating as indicated on the product identification plate.

Position the power supply lead properly so that it will not be walked on or pinched by items placed on or against it.

Do not use the appliance if it has been dropped or any part of the appliance (including the cord or plug) has been damaged.

Do not install the unit on other appliances, on uneven surfaces, or where it could be subject to heat sources (e.g., radiators or stoves), direct sunlight, excessive dust, or mechanical vibrations.

Do not operate the appliance underneath or near flammable or combustible materials (e.g., curtains). Keep at least 300mm clearance around the sides, back, front, and top.

Do not block any ventilation openings.

Do not insert or allow foreign objects to enter the grille openings as this may cause damage to the appliance and/or injury to the user.

To install the batteries, first remove the back of the remote control by pressing down on the Thumb Grip, then sliding the battery cover down and lifting it off.

Insert the batteries inside the battery compartment matching polarity icons with those in the battery compartment.

Refit the cover securely by sliding it back on.

Important: The remote requires 2 x AAA batteries (1.5V), which are not included.

Non-rechargeable batteries are not to be recharged.

Batteries are to be inserted with the correct polarity.

Exhausted batteries are to be removed from the appliance and safely disposed of.

The supply terminals are not to be short-circuited.

Do not mix new and old batteries, or batteries of different types (e.g., Alkaline with Non-Alkaline) in the remote control.

To prevent corrosion, remove the batteries if the remote control will not be used over a lengthy period.

Remove the cable tie and unravel the power cord before operation.

DO NOT run the power cord under the stand.

Plug the power cord into the mains power point and switch it on. The Red Power Indicator light on the Fan’s control panel will illuminate.

Tilt the fan head up or down to your desired position.

Press the On / Off button on the control panel or on the remote control.

When first turned on, the fan will start at default speed 3.

Press the Speed Button and the fan speed will increase to position 4 (high Speed).

Press the Speed Button again and the fan speed will cycle around to position 1 (Low Speed).

Press the Speed Button again and the fan speed will increase to position 2.

Press the Speed Button again and the fan speed will increase to position 3, and so on.

If the fan is left powered on (plugged in and switched on at the wall), the next time you start the fan using the On/Off button, it will start at the last speed setting.

If the fan is switched off at the power point or unplugged, the next time you start the fan, it will default to speed setting 3.

Turn off and unplug the unit from the power source before cleaning.

Never spray with liquids or submerge the unit in water or any other liquid.

Do Not use flammable liquids, chemicals, abrasive creams, steel wool, or scouring pads for cleaning.

Wipe the unit over with a damp (not wet) cloth with fresh clean lukewarm water and mild detergent.

Wipe over again to remove any detergent residue and thoroughly dry before reusing.

Do not let the Control Buttons or Indicator lights get wet or splashed.

If the Fan grilles are dusty, you can use a vacuum cleaner with a “non-rotating” brush attachment to gently vacuum the dust away.

IMPORTANT: Do Not poke any objects into the fan grille slots for any reason.

Switch off and unplug the fan.

Coil the cable loosely. Do not kink or pull the cable tight.

Store your fan in a cool, dry location.

The remote control can be stored in the rear of the base in the provided storage slot.

Do not operate the appliance underneath or near flammable or combustible materials (e.g. curtains). Keep at least 300mm clearance around sides, back, front, and top.

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus that produce heat.

Appliance should not be used outdoors, placed near a hot gas or electrical burner, or placed in a heated oven.

Do not install the unit on uneven surfaces or where it could be subject to direct sunlight, excessive dust, or mechanical vibrations.

If using an extension cord, the technical specifications of the extension cord must match or exceed the technical specifications of this appliance.

Do not allow the cord to hang over the edge of the work surface or to come into contact with stoves or other hot surfaces.

If the cord or plugs are worn or damaged, do not use them.