ANKO HEG45RW (02) PDF Document

The ANKO HEG45RW consists of the following components: 1 Front Grille, 2 Fan Blade Spinner Nut, 3 Fan Blade, 4 Fan Guard Nut, 5 Rear Grille, 6 Motor Head Assembly, 7 Inner chrome tube, 8 Height Adjustment Ring, 9 Stand Post, 10 Plastic collar, 11 Base Cover, 12 Base Weight, 13 Washer, 14 Locking Screw, 15 Remote Control.

First, unscrew the Locking Lever and Washer from the bottom of the stand post. Insert the plastic collar into the top of the plastic base cover. Insert the bottom of the stand post into the collar. Whilst holding the cover and post together, tip up so that the underneath of the cover is accessible. Place the Weight in the centre of the cover and over the end of the post. Finally, fasten in place by use of the Locking Lever and Washer and tighten.

Stand the Base with attached post on the floor. Loosen the post height adjustment locking ring anticlockwise, pull out the inner chrome tube to the desired height and then retighten the locking ring. Place the Motor assembly at the top of the Stand Post and lower it down all the way. If the motor assembly will not slide down the chrome post, loosen the thumb screw on the back of the motor assembly until it can slide down. Tighten the thumb screw clockwise, ensuring you do not overtighten.

First, remove the Fan Guard Nut anticlockwise from the front of the fan motor housing. Fit the rear safety grille into position, ensuring the handle on the back of the grille is at the top, then refit the Nut and tighten. Remove the protective plastic sleeve from the motor spindle shaft and discard it. Place the Fan Blade onto the motor spindle, ensuring the flat side of the motor shaft aligns with the flat side of the fan blade hole. Slide the fan blade all the way on.

Secure the blade into place by gently hand tightening the spinner nut anticlockwise onto the end of the motor spindle. Note that the spinner nut is self-tightening when the motor starts, so do not over-tighten; just nip it up. The Spinner Nut screws on in the opposite way to a normal nut and tightens when rotated anticlockwise.

Open up all locking clips on the sides of the front safety grille. Remove the small nut and bolt from the bottom of the grille. Place the safety grille into position by lining up the location hook over the top of the rear grille and pushing down. Secure the grille by closing the clips over the outer rim. Finally, insert the small bolt through the two holes in the bottom rim of both grilles, screw on the nut, and use a small Philips screwdriver to tighten.

Turn off and unplug the ANKO HEG45RW before adjusting. To adjust the angle, grasp the Fan Grills and tilt the head either upward or downward to your desired angle.

Unscrew the adjustment ring anticlockwise on the outside of the stand post, slide the inner post up or down to the desired height, and then tighten the knob clockwise again to lock it in place.

Remove the back of the remote control by pressing down on the Thumb Grip, then sliding the battery cover down and lifting it off. Insert two 1.5V AAA batteries, ensuring the polarity icons (+ and -) match those marked inside the battery compartment. Place the flat “-” end of the battery on the spring, push down on the spring, and push the top “+” end of the battery into the remote control. Repeat for the other battery and refit the cover securely by sliding it back on until it clips shut.

Using your fingernail or a plastic tool, pry the batteries out by pushing from the top (+) end of the battery and then swing the battery out.

The remote control must be pointed towards the receiver, which is located inside the fan control panel. Do not block the line of sight between the remote control and the fan control panel. Avoid dropping the remote control or knocking it against hard objects.

Ensure the ANKO HEG45RW is assembled correctly, plug it into the power point, and switch it on. The Red “Power” indicator will light up. Press the “ON/SPEED” button on the fan control panel or the remote control once. The “LOW” light and Mode light will illuminate, and the fan will start to spin at Low Speed. Pressing the “ON/SPEED” button again will increase the speed to Medium, and pressing it once more will set the speed to High.

Press the “OFF” button on the remote control or on the fan control panel.

Modes can only be selected with the remote control by pressing the “Mode” button. With the fan running in “Normal” mode (Red Mode Light), press the “MODE” button on the remote control to change to “Natural” mode (Green Mode Light). Press the “MODE” button again to change to “Sleep” mode (Mode Light will turn Off). Pressing the “MODE” button again will cycle back to “Normal” mode.

The “Normal” Mode (Red Light) is set by default when the ANKO HEG45RW is first turned on. In this mode, the wind remains a constant flow.

The “Natural” mode (Green Light) creates variable wind patterns on the ANKO HEG45RW to simulate variable winds. In this mode, the speed of the fan continually cycles through a mixed selection of low, medium, high, and off in set intervals.

The “Sleep” mode (No Mode Light) on the ANKO HEG45RW creates wind patterns similar to the Natural Mode. However, when the fan is set to Medium or High Speed, the pattern will drop a speed level after approximately 30 minutes. After another 30 minutes, it will automatically drop again to the low speed wind pattern until manually turned off.

To select the off time, press the “TIMER” button on the remote control once. It will advance to 0.5h as indicated by the indicator lights. Each consecutive press will advance the timer at 0.5h increments until it reaches a maximum of 7.5h. The time set is the sum of the illuminated lights. To turn off or reset the timer, continue to press the “TIMER” button until it cycles back to where no timer lights are illuminated.

Push the clutch knob on the back of the motor head down to activate the oscillating function. The ANKO HEG45RW head will swing from side to side.

To stop the oscillation, allow the ANKO HEG45RW head to move into the desired position and then pull the clutch knob up.

Yes, the head of the ANKO HEG45RW can be manually rotated left or right to align with the centre of the swing by means of a ratchet system. Do not force it beyond where it physically stops.

Turn off and unplug the ANKO HEG45RW before cleaning. Clean the motor housing and body assembly with a clean, damp cloth and wipe dry. Never spray with liquids or submerge the fan in water or any other liquid. Do not use flammable liquids, chemicals, abrasive creams, steel wool, or scouring pads.

Switch off and unplug the ANKO HEG45RW. Coil the cable loosely; do not kink or pull the cable tight. Store the fan in a cool, dry location.

Read the instruction manual carefully before using the ANKO HEG45RW. Ensure the fan is switched off from the supply mains before removing the guard. Keep the appliance out of reach of young children. Do not disassemble the appliance. Ensure the appliance does not get wet, and do not operate it with wet hands. Do not immerse it in water or use near sinks, baths, or showers. Always operate the ANKO HEG45RW from a power source of the same voltage, frequency, and rating as indicated on the product identification plate.

Position the power supply lead properly so that it will not be walked on or pinched by items placed on or against it. Do not install the ANKO HEG45RW on other appliances, on uneven surfaces, or where it could be subject to heat sources (e.g., radiators or stoves), direct sunlight, excessive dust, or mechanical vibrations. Keep at least 300mm clearance around the sides, back, front, and top.

The ANKO HEG45RW should not be used outdoors, placed near a hot gas or electrical burner, or placed in a heated oven. Do not operate the appliance underneath or near flammable or combustible materials such as curtains. Do not allow curtains, drapes, or any other items to drape across the appliance or its openings. Do not use the product in oily or dirty areas (e.g., the kitchen or smoky places) as the air vents may become blocked.

If the supply cord of the ANKO HEG45RW is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard. If the cord or plugs are worn or damaged, do not use the appliance.

Never carry the ANKO HEG45RW by the cord or pull to disconnect it from the outlet. Instead, grasp the plug and pull to disconnect. Unplug the unit from the power socket by grasping the plug body; do not pull on the cord.

If using an extension cord with the ANKO HEG45RW, the technical specifications of the extension cord must match or exceed the technical specifications of the appliance.

No, the ANKO HEG45RW is intended for household use only and not for commercial or industrial use.

Do not mix new and old batteries or batteries of different types (e.g., Alkaline with Non-Alkaline) in the ANKO HEG45RW remote control. To prevent corrosion, remove the batteries if the remote control will not be used over a lengthy period. Non-rechargeable batteries are not to be recharged. Exhausted batteries are to be removed from the remote control and safely disposed of. The battery supply terminals are not to be short-circuited.

The “Power” indicator on the ANKO HEG45RW is a Red light that illuminates after the fan is assembled correctly, plugged into a power point, and switched on.

The “Mode” light indicates the selected fan mode on the ANKO HEG45RW. A Red light indicates “Normal” mode, a Green light indicates “Natural” mode, and when the Mode Light is off, it indicates “Sleep” mode.

Yes, the ANKO HEG45RW features a power-saving timer function. You can set the fan to turn off automatically after a set period, from 0.5 hours up to a maximum of 7.5 hours, using the “TIMER” button on the remote control.

Ensure the clutch knob on the back of the motor head is pushed down to activate the oscillating function. If it is already pushed down and not moving, do not force it, and ensure it has not been obstructed.

No, the manual does not suggest wall-mounting the ANKO HEG45RW or its remote control. It specifically warns not to hang or wall-mount the appliance itself.

No, there are no user serviceable parts inside the ANKO HEG45RW. Do not disassemble the appliance.

The ANKO HEG45RW is rated for 230 – 240V~ 50Hz 50W.

Ensure that the ANKO HEG45RW is switched off from the supply mains before removing the guard.

Keep the ANKO HEG45RW out of reach of young children. Children should be supervised to ensure that they do not play with the appliance. Additionally, ensure children and babies do not play with plastic bags or any packaging materials from the appliance.

Do not use the ANKO HEG45RW if it has been dropped or if any part of the appliance (including the cord or plug) has been damaged.

Keep at least 300mm clearance around the sides, back, front, and top of the ANKO HEG45RW.

Yes, unplug the ANKO HEG45RW during lightning storms or when unused for long periods of time.

No, never insert fingers or any other objects through the fan guard and ventilation openings of the ANKO HEG45RW, as this may cause damage to the appliance and/or injury to the user.

Turn off and unplug the ANKO HEG45RW before cleaning or storing.

If the ANKO HEG45RW is used by a third party, please supply the instruction manual with it.

No, do not allow the power cord of the ANKO HEG45RW to hang over the edge of a work surface or to come into contact with stoves or other hot surfaces.

Do not install the ANKO HEG45RW near any heat sources such as radiators, heat registers, stoves, or other apparatus that produce heat.

The time set on the ANKO HEG45RW will be indicated by the sum of the lights which are illuminated. For example, if the 0.5h + 2h + 4h lights are illuminated, this adds up to 6.5 hours, and the fan will turn off after approximately 6.5 hours.

No, you should never operate the ANKO HEG45RW without the safety grille properly installed, as this poses a significant safety risk.

The ANKO HEG45RW has three speed settings: Low, Medium, and High.

Remove the cable tie and unravel the cordset of the ANKO HEG45RW before operation. Additionally, do not run the power cord under the stand.

Do not block any ventilation openings of the ANKO HEG45RW.

Yes, but you must not attempt to recharge non-rechargeable batteries in the ANKO HEG45RW remote control.

If the ANKO HEG45RW shows any signs of malfunction, damage, or is not working as expected, discontinue use immediately and unplug it from the power source.