V-ZUG SUPREMO SL (01) PDF MANUAL

The appliance is intended for:

Indoors use.

Preparing coffee and hot water.

Frothing milk and steaming drinks.

Household purposes.

Using the appliance for other purposes than those described may result in danger.

Use the appliance only after it has been installed.

The appliance must be installed and connected up to the electricity supply according to the separate installation instructions. The necessary work should be carried out by a qualified fitter/electrician.

Read the section «Using for the first time» before using the appliance for the first time.

The appliance must be connected to a suitable mains socket.

Mains voltage must correspond to the specifications on the identification plate on the appliance.

Recommendation: connect the appliance via a residual current device (RCD).

The appliance must not be used by children or persons not instructed in its use.

The appliance is dangerous to children. Keep children away. Switch off when unattended.

Keep packaging material out of the reach of children.

Do not point the steam-/hot water nozzle at yourself or others (danger of scalding).

Do not insert any objects into the openings (Danger! High voltage!).

If accessible, do not touch the plug with wet hands or pull it out by the cable.

Caution: you may scald yourself if you come into contact with hot water, steam or the nozzle.

Do not remove the drip tray during preparation, otherwise you may scald yourself with hot drinks.

Do not use the appliance if it is faulty or faults are suspected, e.g. if dropped.

Any repairs should only be carried out by Customer Services or authorised and qualified persons.

Do not use the appliance if the mains cable is defective. Have the mains cable replaced only by Customer Services (Danger! High voltage!).

Switch off the appliance before opening the service door. Danger of scalding!

If possible, disconnect the plug from the mains and allow the appliance to cool down before cleaning.

Do not spray the appliance down with water.

Do not dry any part of the appliance in the oven or microwave.

Empty the water tank and coffee bean hopper.

Empty and clean the drip tray and dregdrawer.

Switch off the appliance.

To test for water hardness: hold the provided test strip under water for one second. Take a reading after one minute.

Compare the reading to the table below:

To set water hardness, go to User Settings/Programming.

1. Open the operating panel by pressing on the strip handle.

2. Remove the water tank.

3. Optional: Insert a water filter (e.g., «Aqua Prima») according to its package instructions. The appliance can be used without a filter, but requires more frequent descaling. Using a filter improves coffee quality and reduces strain on appliance parts. If using a filter, program it in User Settings/Programming.

4. Fill the tank with fresh water (max. 1.7 l).

5. Insert the water tank back into the appliance.

1. Open the operating panel.

2. Remove the coffee bean hopper.

3. Fill with coffee beans (max. 300 g).

4. Insert the coffee bean hopper back into the appliance.

1. Switch on the appliance at the main switch (located behind the operating panel).

2. Close the operating panel. «Ventilate» appears in the plain text display.

For language settings, see «User Settings/Programming».

1. Place a tall vessel under the nozzle.

2. Press the ◊ (Hot water) key and draw hot water until a steady jet of water is produced.

3. Press the ◊ (Hot water) key again to interrupt the flow. «Select product» and «Ready for use» appear in the plain text display.

The flashing symbol in the plain text display denotes the selected user setting.

1. Press ‘P’ (Start).

2. Use the arrow keys (▼▲) to select the Function, then press ‘ok’ (Confirm).

3. Use the arrow keys (▼▲ or < >) to select the desired Setting, then press ‘ok’ (Confirm). Use ‘esc’ to Cancel.

Navigate to ‘Clock’ in the settings menu.

Automatic On/Off: Select Yes or No to activate/deactivate the automatic switch on/off times.

Clock time: Set the current clock time (XX:XX).

On/Off time: Set the desired switch on time (XX:XX) and switch off time (XX:XX).

Show clock time: Select On or Off to display the clock time.

Warning: Hot water and steam can scald! Point nozzle at drip tray.

1. Place 1 or 2 cups under the dispensing head. Preheat cups for hotter coffee. For large cups, push the dispensing head up.

2. Optional: Adjust the AromaControl knob (+/-) to set the coffee strength (mild to strong).

3. Press the Espresso key (single cup symbol): press 1x for 1 cup, press 2x for 2 cups. The display shows “1 espresso Dispensing…”.

To adjust the amount: Place a cup under the dispenser head. Press and hold the Espresso key until the desired quantity is reached. The quantity is stored in memory for future use.

Energy Saving: If the machine is in energy saving mode, press the P key to cancel it before preparing coffee.

Ensure no coffee beans are in the grinder when changing the setting.

Open the service door to access the grinder setting knob (located near the brew unit).

Adjust the knob towards the smaller dots for a finer grind or towards the larger dots for a coarser grind (settings 2 to 10). Finer grinds generally produce stronger coffee.

Note: After starting the steam function, some condensed water will be produced first.

1. Put milk into a suitable vessel. Cold milk froths better. Fill the vessel no more than 1/3 full.

2. Select the desired amount for grinding (Aroma of espresso, coffee, or large coffee) via User Settings if needed.

3. Press the Steam key (steam symbol).

4. Caution: steam spray! Point the nozzle at the drip grill briefly to release condensed water.

5. Immerse the nozzle into the milk and rotate the vessel while frothing.

6. As soon as there is enough froth, press the Steam key again to stop the steam.

7. Remove the vessel.

8. Prepare coffee (e.g., Espresso) and pour it directly into the milk froth.

9. Clean the nozzle immediately: Caution: hot part! Danger of burning! Clean the nozzle immediately after use with a damp cloth.

Danger: Hot water and steam can scald! Point nozzle at drip tray.

1. Place a cup under the nozzle.

2. Press the ◊ (Hot water) key to start dispensing. The display shows “Hot water Dispensing…”.

3. Press the ◊ (Hot water) key again to stop.

1. Place a cup under the nozzle.

2. Press and hold the ◊ (Hot water) key. After about 5 seconds, the second line on the display switches to programming mode (“Programm. water”).

3. Release the ◊ key when the desired amount is reached.

4. Press the ◊ key briefly to confirm and save the amount.

Danger: Hot water and steam can scald! Point nozzle at drip tray.

1. Place a cup/vessel under the nozzle.

2. Note: After the steam function starts, some condensed water is produced first. Point the nozzle at the drip tray briefly.

3. Press the Steam key (steam symbol) to start. The display shows “Steam Dispensing..”.

4. Immerse the nozzle in the drink and warm it by rotating the vessel.

5. Press the Steam key again to stop.

1. Place a suitable container if needed, or point nozzle at drip tray.

2. Press and hold the Steam key. After about 5 seconds, the second line on the display switches to programming mode (“Programm. steam”).

3. Release the Steam key when the desired duration is reached.

4. Press the Steam key briefly to confirm and save the duration.

1. Switch off the appliance.

2. Open the operating panel and remove the water tank and coffee bean hopper.

3. Clean the water tank (including strainers) under running water.

4. Empty and clean the coffee bean hopper.

5. Reinstall the components.

1. Remove the drip tray assembly (tray, grill, dregdrawer) from the front of the appliance.

2. Separate the components.

3. Empty the dregdrawer and drip tray.

4. Clean the drip tray, drip grill, and dregdrawer under running water.

5. Reassemble and insert back into the appliance.

1. Push back the dispensing head. Push the drip guard (if present) to the AromaControl position.

2. Remove the drip tray.

3. Open the service door (the push button is behind the cover).

4. Push the top button on the dispensing head holder and pull the dispensing head forwards.

5. Clean the dispensing head under the tap without detergent.

6. Push the dispensing head back onto the holder until it rests in.

7. Close the service door and replace the drip tray.

1. Pull the lower part of the nozzle downwards to remove it.

2. Clean it under the tap without detergent.

3. Reattach the nozzle part.

Note: For cappuccino preparation, clean the nozzle immediately after use with a damp cloth due to heat.

Proceed with care when using the key.

1. Push the drip guard (if present) to the AromaControl position.

2. Remove the drip tray.

3. Open the service door (pushbutton is behind the cover).

4. Press the PUSH button on the brew unit and pull the brew unit forwards to remove it.

5. Use the provided key: insert it into the top strainer, turn anti-clockwise, and remove the top strainer.

6. Clean/dry everything (brew unit and strainer) under running water without detergent.

7. Reassemble the strainer and brew unit in reverse sequence. Do not press PUSH when reassembling.

8. Insert the brew unit back into the appliance until it clicks.

9. Close the service door and replace the drip tray.

Descale whenever the plain text display shows “Decalcify” or as required. The process lasts approx. 30 minutes and should not be interrupted by switching off the appliance.

Warning: Under no circumstances use vinegar. Use commercially available descaling agents suitable for this appliance.

Preparation:

1. Remove the water filter (if installed).

2. Use descaler according to manufacturer’s instructions and fill the water tank with at least 1 litre of the solution.

3. Re-insert the water tank.

4. Place a large vessel (min. 1 litre capacity) below the nozzle.

5. Press the Descale key (:::) on the control panel.

Starting Descaling:

6. The display shows “Descaling Yes”. Press the key below “Yes” to confirm.

7. Press the P key to start the descaling process. The display shows “Machine is descaling”.

8. Rinsing occurs at 1-minute intervals until the message “Rinse machine Fill watertank” is displayed.

Rinsing:

9. Remove and rinse the water tank thoroughly.

10. Fill the water tank with fresh water.

11. Re-insert the water tank.

12. The display shows “Rinse machine Press water key”. Press the ◊ (Hot water) key. Rinsing begins.

13. Press the ◊ (Hot water) button to cancel and continue the procedure if needed.

14. The cleaning process is completed when the water tank is empty and “Rinsing finished Press water key” is displayed. Press the ◊ (Hot water) key.

Finishing Descaling:

15. Remove and rinse the water tank thoroughly again.

16. Put back the water filter (if used).

17. Fill the tank with fresh water.

18. Insert the water tank.

19. Place the large vessel under the nozzle again.

20. Press the ◊ (Hot water) key. Ventilating begins.

21. Draw hot water until a steady jet is produced.

22. Press the ◊ (Hot water) key to finish.

Perform every 14 days or after 250 cups. Once started, the cycle cannot be interrupted.

Warning: Before starting, empty the drip tray and have a spare vessel handy. Large amounts of water (approx. 8.5 dl) will be produced.

Important: For optimum cleaning, use detergent tablets manufactured by Saeco. Using other products may cause damage.

1. Switch the appliance on.

2. Open the service door, remove the brew unit.

3. Add one detergent tablet to the brew unit.

4. Insert the brew unit back into place and close the service door.

5. Remove, fill, and reinsert the water tank.

6. Place a large vessel below the dispensing head.

7. Press the P key.

8. Navigate using the arrow keys (▼▲) to “Rinsing cycle”.

9. Press the key below the arrow to select “Rinsing cycle”.

10. Confirm by pressing the P key.

11. The display shows “Yes”. Select “Yes” by pressing the key below it (므).

12. Confirm by pressing the P key.

13. Approx. 8.5 dl water is pumped off in approx. 7 minutes.

Turn on the main switch (behind operating panel).

Check power connection.

Check fuse in house wiring system.

Preheat cups with hot water.

Set brewing temperature correctly (User Settings > Temperature).

Switch off appliance!

Clean nozzle.

Close service door.

Switch on appliance (brew unit is initialised).

Switch on main switch.

Adjust illumination setting (User Settings > Illumination).

Disable the appliance to prevent accidents caused by improper use, especially through children playing.

Pull the plug out of the mains socket or have the appliance disconnected from the mains by a qualified electrician. Then cut off the mains cable.

The old appliance should not be discarded as worthless rubbish. If disposed of correctly, the raw materials can be recovered for recycling.

The symbol on the identification plate warns that the appliance may not be disposed of in normal household waste.

The appliance must be disposed of in accordance with local regulations on waste disposal. For more information on handling, disposal and recycling, contact local authorities, local recycling facilities, or the retailer from whom you purchased the appliance.