V-TAC VT-44205 (01) PDF Document

MODEL	SKU	WATTS	LUMENS	BEAM ANGLE	LIFE SPAN	DF	CRI	INPUT VOLTAGE	OPERATION TEMPERATURE	DIMENSION	N.W (KGS)	MAX MOUNTING HEIGHT	PROJECTED AREA (mm²)
VT-4435	9891-5	30W	5550Lm	115°	25000H	>0.9	>70	AC220-240V 50Hz	-20 to +45°c	164.5x153x34mm	0.41	<5M	25168.5
VT-4456	9892-5 9893-5	50W	9250Lm	115°	25000H	>0.9	>70	AC220-240V 50Hz	-20 to +45°c	183.5x169x34mm	0.56	<5M	31011.5
VT-44105	9894-5 9895-5	100W	18500Lm	115°	25000H	>0.9	>70	AC220-240V 50Hz	-20 to +45°c	253.5×242.5x40mm	1.1	<5M	61473.75
VT-44205	9896-5 9897-5	200W	37000Lm	115°	25000H	>0.9	>70	AC220-240V 50Hz	-20 to +45°c	402.5×349.5x44mm	2.8	<5M	140673.75

Please observe the following warnings:

• Please make sure to turn off the power before starting the installation.

• Installation must be performed by a qualified electrician.

• The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.

• If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.

• Replace any cracked protective shield.

• Terminal block not included.

• Proper grounding should be ensured throughout the installation.

• Minimum distance from lighted objects 1m.

• For outdoor use.

Follow these installation instructions:

• DO NOT USE IN AREAS WITH LIMITED VENTILATION OR OUTSIDE THE RATED AMBIENT TEMPERATURE RANGE. *CONNECT WITH WATERPROOF CABLE HOUSE ONLY. *ENSURE ELECTRICITY IS SWITCH OFF BEFORE INSTALLATION.

• Please do not mount to a surface that is prone to vibrations.

• Remove the screw and the bracket afterward. (Figure 1) Before drilling, mark the hole position for fixing the bracket onto the wall (Screw not supplied). (Figure 2)

• Screw the retaining bracket to the wall with a suitable quantity of screws. (Figure 4)

• Mount the bracket back to the fixture. Adjust the floodlight according to the desired position. Tighten the screw. (Figure 5) Connect your main cable (HO5RN F3G1.0mm2 Recommended) with the input lead of our product through the waterproof junction box.

Note: The line (-) of the lead. (Need to use the junction box of IP65 or above, ensure to tighten the waterproof screw) Switch on the power to make sure if the product is working.

Yes, please take note of the following:

• To reduce the risk of strangulation the flexible wiring connected to this luminaire shall be effectively fixed to the wall if the wiring is within arm’s reach.

• In order to maintain the IP protection of the product, the cable entry/gland should be installed on the bottom side.

WIRE LENGTH
30W	150mm
50W	150mm
100W	1 M
200W	1 M

The light source is replaceable (LED only) by a professional. The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person. Note that light source removal will void the warranty.

This marking indicates that this product should not be disposed of with other household wastes.

This symbol means: Caution, risk of electric shock.