TOTALLY WICKED PIPE X (01) PDF Document

To begin using your TOTALLY WICKED PIPE X immediately, follow these steps:

1. Prime the atomizer head.

2. Fill the tank with e-liquid.

3. Insert the battery with the negative side down and touching the spring.

4. Inhale to activate the device.

5. Charge the battery, as it may not have arrived with a full charge.

The TOTALLY WICKED PIPE X consists of the following parts:

Mouthpiece: The curved section used for inhalation.

Tank: The reservoir that holds the e-liquid.

Atomizer Head: The component that heats the liquid into vapour.

Tank Base: The bottom section of the tank assembly.

Battery: A single 18650 power source.

Battery Cap: The removable cover for the battery compartment.

Pipe X Body: The main housing of the electronic pipe.

It is critical to prime a new atomizer head before the first use to prevent the coil from overheating or burning. To prime the TOTALLY WICKED PIPE X:

1. Remove the mouthpiece by pulling it straight off.

2. Unscrew and remove the tank assembly from the pipe body.

3. Unscrew the tank base to access the atomizer head.

4. Drip a few drops of e-liquid directly onto the side e-liquid inlets of the atomizer head.

5. Once the tank is filled and reassembled, wait 5 minutes before vaping to ensure the atomizer head is fully saturated with e-liquid.

To fill the TOTALLY WICKED PIPE X tank with e-liquid:

1. Remove the mouthpiece and unscrew the tank from the pipe body.

2. Unscrew the tank base.

3. Pour e-liquid into the tank until it reaches just below the height of the central air tube. Avoid getting any liquid inside the central air hole.

4. Screw the tank base back onto the tank.

5. Screw the assembled tank back onto the pipe body.

6. Refit the mouthpiece by pushing it firmly over the tank, ensuring the alignment tab is correctly oriented.

To fit the battery into the TOTALLY WICKED PIPE X:

1. Invert the device and turn the battery cap anti-clockwise until it is released.

2. Insert a 18650 battery into the housing with the negative side first.

3. Place the top cap back on so the tabs align with the cutouts in the pipe body.

4. While holding the cap down, rotate it one quarter turn clockwise to lock it.

5. The LEDs will flash 3 times to confirm the battery has been successfully inserted.

The TOTALLY WICKED PIPE X uses automatic atomizer activation. Simply draw gently but firmly on the mouthpiece. The LED will light up to indicate the device is operating and producing vapour.

If the draw feels too airy or too tight, you can adjust the airflow of the TOTALLY WICKED PIPE X:

1. Remove the mouthpiece and unscrew the tank assembly from the pipe body.

2. Locate the adjustable airflow ring at the bottom of the tank base.

3. Rotate the ring clockwise to open the airflow or anti-clockwise to close it.

4. You can check the adjustment by drawing on the tank assembly while it is still removed from the pipe body before reassembling.

To prevent the atomizer head from drying out and burning, ensure the e-liquid level does not drop below the fluid feed holes on the sides of the atomizer head. Because the tank is partially obscured, you must remove the mouthpiece to view the fluid level through the glass windows of the tank.

The TOTALLY WICKED PIPE X uses a removable 18650 Li-ion battery. To charge the device, remove the battery and use an appropriate external 18650 battery charger, following the specific instructions provided with that charger.

Atomizer heads generally last from several days to several weeks depending on vaping style and e-liquid type. You should replace the head if you notice a burnt taste, a reduction in flavour intensity, or a loss of vapour production. To replace it:

1. Unscrew the tank assembly and the tank base.

2. Unscrew the old atomizer head from the tank base.

3. Screw in a new TOTALLY WICKED PX atomizer head.

4. Follow the priming steps and wait 5 minutes after filling before use.

The TOTALLY WICKED PIPE X uses LED flashes to communicate various protections and statuses:

Low Battery: The LED will flash 10 times when the battery voltage drops to 3.4V, indicating it needs to be charged.

Short Circuit Protection: The LED will flash 4 times if a short circuit is detected. Power will be cut off; replacing the atomizer head usually resolves this.

No Atomizer Detected: The LED will flash 5 times if the device cannot detect an atomizer. Ensure the head is fully screwed into the base and the tank is properly fitted to the battery.

Atomizer Head Protection: The LED will flash 10 times if the device is operated continuously for more than 10 seconds. Power will be cut off automatically and resume on the next use.

Proper maintenance ensures the longevity of the TOTALLY WICKED PIPE X:

1. Wipe the pipe body, mouthpiece, and connection threads with a dry cloth or tissue.

2. The mouthpiece, tank, and base can be washed under warm running water when they are disassembled. Ensure these parts are completely dry before refitting the atomizer head.

3. Never clean the atomizer head with water.

4. Do not submerge the main Pipe X body in water or allow it to get wet.

The specifications for the TOTALLY WICKED PIPE X are as follows:

Follow these safety guidelines for the TOTALLY WICKED PIPE X:

Store the device and accessories away from children when not in use.

Do not charge the battery in damp environments or in temperatures below 0 degrees Celsius or above 45 degrees Celsius.

Do not use the device in temperatures below -10 degrees Celsius or above 60 degrees Celsius.

Do not carry batteries in pockets or bags with other metallic objects.

Do not attempt to repair a faulty device or battery, as they are sealed units with no serviceable parts.