FREE ENGLISH TOHNICHI FTD10CN-S (01) PDF DOCUMENT.
FREE ENGLISH TOHNICHI FTD10CN-S (01) PDF USER GUIDE.
FREE ENGLISH TOHNICHI FTD10CN-S (01) PDF USER MANUAL.
FREE ENGLISH TOHNICHI FTD10CN-S (01) PDF OWNER GUIDE.
FREE ENGLISH TOHNICHI FTD10CN-S (01) PDF OWNER MANUAL.
FREE ENGLISH TOHNICHI FTD10CN-S (01) PDF REFERENCE GUIDE.
FREE ENGLISH TOHNICHI FTD10CN-S (01) PDF INSTRUCTION GUIDE.
FREE ENGLISH TOHNICHI FTD10CN-S (01) PDF REFERENCE MANUAL.
FREE ENGLISH TOHNICHI FTD10CN-S (01) PDF INSTRUCTION MANUAL.
FREE ENGLISH TOHNICHI FTD10CN-S (01) PDF OPERATING INSTRUCTIONS.
CLICK HERE TO DOWNLOAD TOHNICHI FTD10CN-S (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What are the main components of the TOHNICHI FTD10CN-S?
The main components of the TOHNICHI FTD10CN-S torque driver are:
• Bit (Optional)
• Main Pointer
• Scale Plate
• Memory Pointer
• Handle
What are the key warnings for using the TOHNICHI FTD10CN-S?
Please observe the following warnings when using the TOHNICHI FTD10CN-S:
• Make sure there is no oil or grease on the grip. A slip of the hand while tightening may cause an accident or injury.
• Check for cracks, scratches, and rust. These can cause damage to the driver and may result in an injury. If such conditions exist, have a functional test performed and repair if necessary.
What precautions should I take when using the TOHNICHI FTD10CN-S?
• Do not use the torque driver beyond the maximum torque setting. This will cause damage or injury.
• Do not use the torque driver if it is missing a pin or scale plate, etc. Have the tool inspected and repaired before using.
• Do not modify the torque driver. Modifications will weaken the torque driver and may cause errors in accuracy, as well as cause an accident or injury.
• Do not drop the torque driver or apply a strong shock or jolt. This will cause damage or deformation and decrease accuracy and durability, which may cause an accident or injury.
• Use only parts designated by Tohnichi for repair of the torque driver.
What are the precautions for use of the TOHNICHI FTD10CN-S?
• Confirm that the driver is set according to the correct unit of measure before using (e.g., kgf·cm, N·m, etc.).
• Do not use the torque driver in fresh water or sea water. The internal mechanism will go bad and can cause an accident or injury. If you drop it in water, get it checked out or repaired.
• Use the correct bit that fits the screw you are using.
• Perform regular inspections for function and accuracy. Periodical inspections are essential to ensure the torque wrench is in optimal condition, thus preventing injury.
• Remove any dirt such as dust, mud, oil, and water after each use and before storing the torque driver.
How should I store my TOHNICHI FTD10CN-S for a long period?
When storing the TOHNICHI FTD10CN-S for a long time, set it at the minimum torque and keep it in a dry place. If improperly stored, the accuracy and durability will decrease rapidly.
How should I properly attach or detach a bit from the TOHNICHI FTD10CN-S?
To attach or detach a bit or a socket, hold the shaft of the driver. If you hold the grip when you attach or detach a bit or a socket, the torque driver might be broken.
How do I operate the TOHNICHI FTD10CN-S?
Follow these steps to operate the TOHNICHI FTD10CN-S:
1. Insert the bit into the bit holder.
2. Set the main pointer to the “0” position on the scale plate. The pointer should be at the “0” position.
3. Move the memory pointer to the “0” position opposite of the measuring direction.
4. Start the measuring or tightening operation.
What are the specifications for the TOHNICHI FTD10CN-S and other FTD-S series models?
The following table lists the specifications for the FTD-S series models, which have an accuracy of ±3%.
| MODEL | CAPACITY | BOLT SIZE (REF) | OVERALL LENGTH | WEIGHT | ACCESSORY BIT | |||
|---|---|---|---|---|---|---|---|---|
| MIN-MAX | 1 GRAD. | SMALL SCREW | TAPPING SCREW | + | thickness×width | |||
| FTD2CN-S | 0.3~2 cN·m | 0.05 cN·m | M1 | M1 | 151mm | 0.14kg | #3 | 1.2×8 |
| FTD5CN-S | 0.5~5 | 0.1 | M1.2 | (M1.1) M1.2 | ||||
| FTD10CN-S | 1~10 | 0.2 | M1.6 | (M1.4) M1.6 | ||||
| FTD20CN-S | 3~20 | 0.5 | M2 | (M1.8) M2 | 272 | 0.37 | ||
| FTD50CN2-S | 5~50 | 1 | M2.5 | (M2.2) | ||||
| FTD100CN2-S | 10~100 | 2 | M3 (M3.5) | M2.5 M3 | ||||
| FTD200CN2-S | 30~200 | 5 | M4 | (M3.5) | ||||
| FTD400CN2-S | 50~400 | 10 | M5 | M4 | 338 | 0.9 | ||
| FTD8N2-S | 1~8 N·m | 0.2 N·m | M6 | (M4.5) | ||||
| FTD16N2-S | 3~16 | 0.5 | M8 | M6 (M7) | ||||
What is the optional Torque Driver Tester used for, and what are its specifications?
The optional Torque Driver Tester is used for torque driver inspection and calibration.
| MODEL | TORQUE MEASUREMENT RANGE CAPACITY cN·m MIN ~ MAX |
1 digit |
|---|---|---|
| TDT60CN3 | 2 ~ 60 | 0.005 |
| TDT600CN3 | 20 ~ 600 | 0.05 |
CLICK HERE TO DOWNLOAD TOHNICHI FTD10CN-S (01) PDF DOCUMENT