FREE ENGLISH TOHNICHI FTD100CN2-S (01) PDF DOCUMENT.
FREE ENGLISH TOHNICHI FTD100CN2-S (01) PDF USER GUIDE.
FREE ENGLISH TOHNICHI FTD100CN2-S (01) PDF USER MANUAL.
FREE ENGLISH TOHNICHI FTD100CN2-S (01) PDF OWNER GUIDE.
FREE ENGLISH TOHNICHI FTD100CN2-S (01) PDF OWNER MANUAL.
FREE ENGLISH TOHNICHI FTD100CN2-S (01) PDF REFERENCE GUIDE.
FREE ENGLISH TOHNICHI FTD100CN2-S (01) PDF INSTRUCTION GUIDE.
FREE ENGLISH TOHNICHI FTD100CN2-S (01) PDF REFERENCE MANUAL.
FREE ENGLISH TOHNICHI FTD100CN2-S (01) PDF INSTRUCTION MANUAL.
FREE ENGLISH TOHNICHI FTD100CN2-S (01) PDF OPERATING INSTRUCTIONS.
CLICK HERE TO DOWNLOAD TOHNICHI FTD100CN2-S (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What safety warnings should I be aware of when using the TOHNICHI FTD100CN2-S torque driver?
Make sure there is no oil or grease on the grip. A slip of the hand while tightening may cause an accident or injury.
Before use, check for cracks, scratches, and rust. These conditions can cause damage to the driver and may result in an injury. If such conditions exist, have a functional test performed and repair if necessary.
What are the main operational precautions for the TOHNICHI FTD100CN2-S torque driver?
Do not use the torque driver beyond the maximum torque setting, as this will cause damage or injury.
Do not use the torque driver if it is missing a pin, scale plate, or other parts. It should be inspected and repaired before using.
Do not modify the torque driver. Modifications will weaken the driver and may cause errors in accuracy, as well as cause an accident or injury.
Do not drop the torque driver or apply a strong shock or jolt. This can cause damage or deformation, and decrease accuracy and durability, which may lead to an accident or injury.
How should I operate the TOHNICHI FTD100CN2-S torque driver?
1. Insert the bit into the bit holder.
2. Set the pointer to the “0” position on the scale plate. The pointer should be at the “0” position.
3. Move the memory pointer to the “0” position opposite of the measuring direction.
4. Start the measuring or tightening operation.
What are the precautions for using the TOHNICHI FTD100CN2-S?
Confirm that the driver is set according to the correct unit of measure before using (e.g., kgf·cm, N·m, etc.).
Do not use the torque driver in fresh water or sea water. The inside mechanism will go bad and cause an accident or injury. If you drop it in water or sea water, get it checked out or repaired.
Use the correct bit that fits the screw you are using.
How do I correctly attach or detach a bit from the TOHNICHI FTD100CN2-S?
When you attach or detach a bit or a socket, hold the shaft of the driver. If you hold the grip when you attach or detach a bit or socket, the FTD might be broken.
How should I maintain and store the TOHNICHI FTD100CN2-S torque driver?
Perform regular inspections for function and accuracy. Periodical inspections are essential to ensure the torque wrench is in optimal condition, thus preventing injury.
Remove any dirt such as dust, mud, oil, and water, etc., after each use and before storing the torque driver.
When storing the torque driver for a long time, keep it in a dry place. If improperly stored, the accuracy and durability will decrease rapidly.
What parts should be used for repairing the TOHNICHI FTD100CN2-S?
Use only parts designated by Tohnichi for repair of the torque driver. When you repair, use only Tohnichi parts.
What are the specifications for the TOHNICHI FTD100CN2-S and other FTD2-S series models?
The following are the specifications for the FTD-S series S.I. Models, which have an accuracy of ±3%.
| MODEL | CAPACITY | BOLT SIZE (REF) | OVERALL LENGTH | WEIGHT | ACCESSORY BIT (thickness×width) | ||
|---|---|---|---|---|---|---|---|
| MIN-MAX | 1 GRAD. | SMALL SCREW | TAPPING SCREW | ||||
| FTD2CN-S | 0.3–2 cN·m | 0.05 cN·m | M1 | M1 | 151mm | 0.14kg | #3 1.2×8 |
| FTD5CN-S | 0.5–5 | 0.1 | M1.2 | (M1.1) M1.2 | |||
| FTD10CN-S | 1–10 | 0.2 | M1.6 | (M1.4) M1.6 | |||
| FTD20CN-S | 3–20 | 0.5 | M2 | (M1.8) M2 | 272mm | 0.37kg | |
| FTD50CN2-S | 5–50 | 1 | M2.5 | (M2.2) | |||
| FTD100CN2-S | 10–100 | 2 | M3 (M3.5) | M2.5 M3 | |||
| FTD200CN2-S | 30–200 | 5 | M4 | (M3.5) | |||
| FTD400CN2-S | 50–400 | 10 | M5 | M4 | 338mm | 0.9kg 0.93kg |
|
| FTD8N2-S | 1–8 N·m | 0.2 N·m | M6 | (M4.5) | |||
| FTD16N2-S | 3–16 | 0.5 | M8 | M6 (M7) | |||
What is the Torque Driver Tester used for?
This tester is used for torque driver calibration. Specifications are below:
| MODEL | CAPACITY cN·m | 1 digit | |
|---|---|---|---|
| MIN | MAX | ||
| TDT60CN3 | 2 | 60 | 0.005 |
| TDT600CN3 | 20 | 600 | 0.05 |
CLICK HERE TO DOWNLOAD TOHNICHI FTD100CN2-S (01) PDF DOCUMENT