TIMAGO FLASH-TIM (01) PDF DOCUMENT

Please adhere to the following safety information when using the TIMAGO FLASH-TIM electric wheelchair:

• Read the manual before first use.

• Do not use the wheelchair until fully assembled.

• Use of the wheelchair by people who are unable to operate it independently is not recommended.

• Maximum load capacity must not exceed 120 kg.

• The wheelchair can only be used by one person at a time.

• It is recommended to keep your feet on the footrest and your forearms on the armrests when driving.

• Always check the battery level on the control panel before use.

• This electric wheelchair should only be used on a flat surface or at low elevations. It should not be ridden on a surface inclined at an angle of more than 8 degrees.

• Do not drive the wheelchair at maximum speed when going uphill or downhill.

• Do not use the wheelchair on soft and slippery surfaces such as mud, sand etc.

• Do not ride the wheelchair sideways on highly elevated areas.

• Do not put any additional load such as a trailer etc. on the wheelchair.

• Do not repair or modify the construction of the wheelchair by yourself. Use only original spare parts provided by the manufacturer.

• Do not stand up or sit down on the wheelchair when the control module is switched on.

• Do not use the wheelchair without anti-tip wheels.

• When the freewheel (manual) mode is on, do not get on or off the wheelchair without assistance.

• Do not lean forward to grab items laying in front, on the side or behind the wheelchair. Do not stand on the footrest. It might result in the wheelchair falling over.

• Avoid rapid changes of the direction while driving on elevations.

• Always slow down while driving downhill or making turns.

• Before use check if the wheels are correctly mounted.

• Do not make sudden moves while using the joystick.

• When storing, protect the wheelchair from rain and adverse weather conditions.

• Before turning on the wheelchair, make sure that the levers are set to electric mode.

• Avoid areas with horizontal gaps.

• If the wheelchair is not going to be used for a long period of time, remove the battery.

• Do not use the wheelchair on the road. It might result in a car accident.

• Do not store the wheelchair in places with high temperatures and humidity.

The TIMAGO FLASH-TIM electric wheelchair is designed for people who have problems with mobility, helping disabled patients with their everyday tasks. It can replace a standard wheelchair. It is suitable for patients with:

• disability, who have problems with unassisted movement,

• dysfunctions and reduced movement,

• heart and cardiovascular system diseases,

• weakening body due to advanced age.

The main elements of the TIMAGO FLASH-TIM are:

1. Handle

2. Backrest

3. Seat

4. Armrest

5. Control module

6. Support wheel for transportation

7. Rear wheel 12″

8. Front wheel 8″

9. Footrest

10. Bag

11. Security buckle

12. Mounting screw

13. Folding button

14. Lithium battery

15. Engine (mode) levers

• Aluminium, folding frame

• Solid rear 12″ and front 8″ wheels

• Control module: on/off button, steering joystick, horn button, speed adjustment, battery level indicator, mute button

• Safe and reliable electromagnetic brake

• Fully closed, maintenance-free battery

• Security belt and anti-tip wheels

• Pocket for small goods located at the back

• Two modes of operation: electric and manual

• Strap – for securing a folded wheelchair

Unfolding: Take the wheelchair out of the box. Unfold it, till you hear a “click” sound. Connect the power cable to the battery.

Folding: To fold the wheelchair, unlock the clamp located at the back, grab the handle and push it down. For extra security, to prevent the wheelchair from unfolding, use the strap included. Note! Disconnect the power cable from the battery before unfolding.

Control module position: Adjustment should be done while seated. Loosen the mounting screw and adjust the position of the panel. Tighten the screw.

Armrest tilting: Press the buttons located on the outside of the wheelchair to lift the armrests. To lower the armrest, pull them down until you hear a “click” sound.

Anti-tip wheels assembly: Put the wheels into the mounting openings located at the back of wheelchair and pull the lever next to it to secure the wheels in place.

Removing the battery: to remove the battery, unlock the buckle located underneath and slowly pull the battery out.

• Joystick (A) – used to control the speed and direction. The further the joystick is pushed away from the middle, the faster the wheelchair will move. It will lose speed automatically after the joystick is released.

• Turn on/off button (B)

• Speed indicator has 5 levels (C): 1 – slowest, 5 – fastest.

• Horn button (D) – press to use the horn.

• Speed adjustment buttons (E) – use +/- to increase or decrease the speed.

• Battery level indicator (F)

• Mute button (G)

• USB port and module with flashlight (H)

To use the wheelchair in manual mode, move down the left and right engine levers located at the back. To use it in electric mode, move the levers up.

• The set includes a charger dedicated to the battery.

• Battery charging time is around 6 hours.

• Plug the charger into the charging port located in the control module or on the battery.

• Connect the charger to a power supply.

• NOTE: Before plugging the charger in, turn off the control panel.

• An orange light indicates that the battery is being charged, while a green light informs that it is fully charged. After the charging is finished, the charger turns off to avoid overcharging.

• Check the connection.

• To avoid the risk of fire, do not modify or disconnect the charging circuit while charging the battery.

• Select the desired driving mode. Note! Do not switch ride mode while driving on elevation.

• Push the power button to check the proper functioning of brakes. Brakes are working correctly (electric mode) if you cannot push the wheelchair. Otherwise, contact the Seller.

• Tilt the footrest and sit comfortably on the seat. Lower the footrest back to a horizontal position. Note! Do not use the footrest as a support when sitting down or standing up from the wheelchair. This may cause the wheelchair to tilt and fall.

• Sit on the wheelchair and turn the control panel on. The lights will light up. The joystick should be in the neutral position.

• Take caution when using for the first time. Control the speed and direction carefully. The electromagnetic brake will get released only after pushing the joystick (electric mode). To speed up, push the joystick further away from its neutral position. To slow down – do the opposite.

• To stop the wheelchair, release the joystick. Pressing the power button will also stop the wheelchair.

• Using dedicated buttons on the control panel, adjust the wheelchair’s speed according to the user’s physical state and road conditions.

• The wheelchair should only be used on flat surfaces. Driving on muddy or uneven surfaces can cause control system damage.

Note! Some parameters might vary depending on user weight, road conditions and battery usage.

• It is recommended to regularly inspect the construction and its elements (wheels, frames, cables, control module, brakes etc.).

• Any used or damaged wheelchair parts need to be replaced (in such case, please contact the Seller).

1) Regularly check the battery level displayed. If the level is very low, charge it immediately to avoid a voltage drop (which may affect battery life).

2) If the wheelchair won’t be used for a longer period of time, charge the battery at least once a month.

3) The battery has a certain lifespan. Exchange your battery if it wears out.

4) The battery should be kept clean and away from kids. Avoid causing any shock or damage to the battery.

5) Charge it regularly to expand its lifespan.

6) Used batteries should be utilized according to local environmental regulations.

TRANSPORTATION

• Take caution during transportation. Do not throw, turn over or put pressure on the product and its packaging.

• For wheelchair folding, check the “Assembly and adjustment” section.

STORAGE

The wheelchair should be kept in a dry and well-ventilated space. Avoid: high temperature and its rapid changes, acids, alkalis and corrosive chemicals.

STORING CONDITIONS

Temperature: -25[°C] ~+55[°C]

Humidity: 30-75%

In the event of a malfunction, the control module will indicate it with a beep and a flashing diode. The number of beeps and LED flashes will help to identify the problem.