SONY MDR-ZX750BN (01) PDF DOCUMENT

Connect the SONY MDR-ZX750BN and a booted computer using the supplied micro-USB cable. When the unit and the computer are connected, charging starts and the indicator (red) lights up. Charging is completed in about 2.5 hours at most and the indicator (red) goes off automatically.

Note: Use the micro-USB cable supplied. You may not be able to charge the unit with other cables.

By touching the unit with an NFC-compatible smartphone, the unit turns on automatically and proceeds to pairing and BLUETOOTH connection.

Compatible smartphones: Smartphones with the NFC function built-in (OS: Android 2.3.3 or later, excluding Android 3.x).

Preparation on the smartphone:

1. Download and install the app “NFC Easy Connect” on the smartphone. If your smartphone has an NFC function, such as that of Android 4.1 or later, you may not need to install this app.

2. Set the smartphone so that the NFC function can be used. For details, refer to the instructions of the smartphone.

Connection Steps:

1. Unlock the screen of the smartphone. If you installed the app “NFC Easy Connect”, start the app.

2. Touch the smartphone on the N-marked part of the unit. Refer to the manual of your smartphone for the designated location to be touched.

Follow the on-screen instructions to complete the connection.

To disconnect, touch the smartphone to the N-marked part of the SONY MDR-ZX750BN again.

Before pairing, ensure the SONY MDR-ZX750BN is charged.

1. Place the BLUETOOTH device within 1 meter of the SONY MDR-ZX750BN.

2. Enter pairing mode on the headphones. Press and hold the POWER button for more than 7 seconds. Make sure that the indicator flashes blue and red alternately after you release the button.

3. Perform the pairing procedure on the BLUETOOTH device to detect the headphones. When the list of detected devices appears on the display of the BLUETOOTH device, select “MDR-ZX750BN”. If passkey input is required on the display of the BLUETOOTH device, input “0000”.

4. Make the BLUETOOTH connection from the BLUETOOTH device.

1. Turn on the unit. Press and hold the POWER button for about 2 seconds while the unit is turned off. Make sure that the indicator flashes blue after you release the button.

2. Make the BLUETOOTH connection from the BLUETOOTH device.

After connecting to your BLUETOOTH device, you can control music playback from the SONY MDR-ZX750BN.

Play/pause: Press the ►II button.

Stop: Hold the ►II button down.

Next/previous: Press the ►►I / I◄◄ buttons.

Fast forward/fast reverse: Hold the ►►I / I◄◄ buttons down.

Volume +/-: Use the VOLUME +/- buttons.

Note: The available functions may vary depending on the BLUETOOTH device. When you operate the buttons, it may operate differently or may not work at all.

To make a call, operate your mobile phone.

When an incoming call arrives, press the call button on the unit to answer. If you are listening to music, the playback will pause during the call and resume automatically when the call is over (may not resume with some devices).

To terminate a call, press the call button on the unit again.

The volume for a call and for listening to music can be adjusted independently.

You can use the SONY MDR-ZX750BN as ordinary wired noise canceling headphones by connecting the supplied cord. Make sure you insert the plug firmly.

Notes:

The BLUETOOTH function is disabled when wired.

The VOLUME +/-, ►II, and ►►I/I◄◄ buttons cannot be used.

To turn on the noise canceling function:

Press and hold the POWER button for about 2 seconds when the unit is turned off. When the unit and the noise canceling function have turned on, the NC button lights up. The noise canceling mode is set to NC mode B.

To turn off the noise canceling function:

When using via the BLUETOOTH connection: Press the NC button. The NC button light goes off. To turn the function on again, press the NC button again.

When the supplied cord is connected: Press the POWER button for more than 2 seconds. The power and the noise canceling function will be turned off.

AI Noise Canceling is a function that automatically selects the most effective noise canceling mode by immediately analyzing ambient sound components.

To activate it, when the unit is on, press and hold the NC button until a beep sounds. The unit starts analyzing ambient sound components for approximately 3 seconds. During analysis, sound volume from the headphones is lowered and the NC button blinks. When analysis is completed, the most effective noise canceling mode is set automatically, and the sound volume returns to normal.

Noise canceling mode types:

1. Terminate the BLUETOOTH connection by operating the BLUETOOTH device.

2. Press and hold the POWER button for about 2 seconds. The indicator (blue) goes off and the headset turns off.