SHARPER IMAGE SBT2014 (01) PDF Document

The following items are included with your SHARPER IMAGE SBT2014 sound bar:

• Wireless Sound Bar

• 3.5 mm AUX IN Cable

• 3.5mm RCA Cable

• 2 Screws

• Remote Control

• AC Adapter

Side Panel Buttons:

• [POWER] button: Power On/OFF

• [MODE] button: Select AUX-IN or Bluetooth mode.

• [VOL-] button: Long press to decrease the volume. Quick press to replay the previous track.

• [▶II] button: Play and pause music.

• [VOL+] button: Long press to increase the volume. Quick press to skip to the next track.

Side Panel Ports:

• Optical In: Audio port

• LINE IN 1: AUX-IN jack

• LINE IN 2: AUX-IN jack

• DC14V jack

Front Panel Indicators:

• LINE IN 1/2 LED indicator

• Optical IN indicator

• Bluetooth LED indicator

• Infrared sensor

1. Connect the small end of the AC adaptor to the DC12V port on the side of the speaker.

2. Plug the AC adaptor to an available power outlet.

3. Press the [POWER] button to activate the sound bar.

1. Measure a width of 32 inches on the wall.

2. Mark the position of the mounting screws on the wall using a pencil.

3. Drill the supplied screws directly into the marks that you have made on the wall and leave approximately 0.3 inch length to hook the Wireless Sound Bar.

4. Put the Wireless Sound Bar onto the mounting screws. Make sure they are firm and stable.

Initial Setup:

The li-ion CR2025 battery (included) is protected with a plastic pull tab to prevent battery drain. To remove the pull tab, pull the tab away from the battery compartment. Your remote is now ready for use.

Replacing the Battery:

To replace the battery, push gently on the tab below the battery compartment and slide out the battery in the remote control. Replace the battery with a new CR2025 with the positive end (+) facing up. Slide the battery back in the remote control.

• Power button: Press to place the speaker in “Sleep” mode. Press again to wake the speaker.

• [MODE] button: Quick press to switch between BT and AUX modes.

• Mute button: Immediately decreases the volume level to 0.

• [I◀◀] button: Press to skip to a previous track.

• [▶II] button: Press once to play music. Press again to pause music.

• [▶▶I] button: Press to skip to the next track.

• [-] button: Quick press to gradually decrease the volume. Press and hold to rapidly decrease the volume.

• [RESET] button: Restore settings.

• [+] button: Quick press to gradually increase the volume. Press and hold to rapidly increase the volume.

1. Quick press the [POWER] button on the control panel or the power button on the remote to turn the sound bar on. Use the [MODE] button on the speaker or remote to select Bluetooth mode. A tone will be heard and the Bluetooth indicator will quickly flash GREEN. The speaker is now in pairing mode.

2. Turn on your mobile device’s Bluetooth function and make it discoverable. (Consult your mobile device’s documentation to connect or setup a Bluetooth device).

3. In discoverable mode, your phone is searching for nearby Bluetooth devices. When your mobile device finds the speaker, select “SBT2014” from the list of discovered devices.

4. Some older mobile devices may ask for a password before connecting to a Bluetooth device. Type 0000 or 1234 and press YES or OK to pair the two units.

5. After a successful pairing, a tone will be heard and the LED indicator light will remain BLUE. When music is playing, the Bluetooth indicator light will flash BLUE slowly.

Powering On/Off:

Quick press the [POWER] button on the speaker or the power button on the remote to turn the speaker on. Quick press either button again to turn off.

Controlling Volume From the Speaker:

• Long press the [VOL+] button on the speaker to increase the volume.

• Long press the [VOL-] button on the speaker to decrease the volume.

Controlling Volume From the Remote:

• Quick press the [-] button to gradually decrease the volume. Long press to rapidly decrease the volume.

• Quick press the [+] button to gradually increase the volume. Long press to rapidly increase the volume.

Playing Music:

• Quick press the [VOL-] button on the speaker to replay the previous track in your playlist.

• Quick press the [VOL+] button to skip to the next track in your playlist.

• Quick press the [▶II] button on the speaker or remote to pause the music. Press the [▶II] button again to resume music playback.

1. Connect one end of the 3.5mm auxiliary cable to the LINE IN 1 or LINE IN 2 port on the left side of the speaker’s control panel. The LINE IN LED indicator will illuminate BLUE for LINE IN 1. If there is a device connected to LINE IN 2, press the [MODE] button again on the speaker or the remote. The LED indicator will now turn RED.

2. Insert the other end of the 3.5mm auxiliary cable into the headphone port on your smart phone, tablet or MP3 player.

3. Open the media player on your mobile device and press “Play” to begin music playback. When the 3.5mm auxiliary cable is removed from the speaker, the Bluetooth indicator light will flash BLUE quickly and reconnect with the last paired device.

NOTE: When a device is connected to the speaker’s LINE IN jacks, you can use your device’s media player to control the volume, repeat or skip music tracks. When disconnecting the auxiliary cable, use the [MODE] button to return to Bluetooth mode.

1. Connect one end of the optical audio cable (not included) to the OPTICAL port on the side of the sound bar.

2. Connect the other end of the optical cable to the Optical / Digital Out port on your TV or other external device.

3. Quick press the [POWER] button on the speaker or the power button on the remote to turn the speaker on.

4. Continue pressing the [MODE] button until OPTICAL is selected.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination during lightning storms or when unused for long periods of time.

13. Unplug the apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel.

15. WARNING: The mains plug is used as a disconnect device; the disconnect device shall remain readily operable.

16. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing, and objects filled with liquids, such as vases, shall not be placed on apparatus.

17. This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to electrical earth.

• Battery shall not be exposed to excessive heat such as sunshine, fire or the like. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

• CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

• CAUTION: Use of controls or adjustments or performance of procedures other than those specified may result in hazardous radiation exposure.

• WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

• WARNING: Do not place this unit directly onto furniture surfaces with any type of soft, porous, or sensitive finish. As with any rubber compound made with oils, the feet of this unit may cause marks or staining where they reside. We recommended using a protective barrier such as a cloth or a piece of glass between the unit and the surface to reduce the risk of damage and/or staining.

• WARNING: Use of this unit near fluorescent lighting may cause interference regarding use of the remote. If the unit is displaying erratic behavior move away from any fluorescent lighting, as it may be the cause.

• WARNING: Shock hazard – Do Not Open.

• WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.