BISSELL CLEANVIEW SWIVEL PET SELECT 2255 (01) PDF Document

The box includes the following items:

1. Vacuum Base

2. Handle

3. Hose

4. 2 Screws (taped to Handle)

5. Extension Wand Base

6. Extension Wand

7. Flexible Pet Crevice Tool

8. Pet TurboEraser® Tool

9. Dusting Brush

10. Febreze® BISSELL® Style 1214 Filter

A Phillips-head screwdriver is required for Assembly in Step 1.

1. Place the upper handle onto the base and push it down. Then attach the handle with the 2 screws taped to the handle in a plastic bag.

2. Insert the extension wand base and turn it to the right to lock in place.

3. Insert the stretch hose end into the back of the vacuum and twist right to lock in place.

4. Wrap hose up and around the hose wrap on the handle. Slide end of hose into vacuum base.

5. To install the optional Febreze® filter, press the tank release button and pull tank from vacuum. Lift tab to access and remove foam filter from lid.

6. Replace foam filter with Febreze® filter. Close tank lid. Place tank back on vacuum and press firmly until you hear a “click.”

7. Put your accessory tools on the vacuum. Note that the crevice tool is stored inside the extension wand.

To turn the vacuum ON, press the red power pedal with your foot. Press it once again to turn the vacuum OFF.

To recline the vacuum, press the recline pedal and pull the handle back towards you.

Turn the dial on the foot of the vacuum to the desired setting. If the dial is difficult to turn, tilt the vacuum back slightly to take the weight off the foot while turning.

Lowest setting: For low pile carpet or bare floors. To pick up debris, it may be necessary to move up one setting.

Medium setting: For medium pile carpet.

Highest setting: For high pile and most shag carpet.

Tip: For optimal carpet cleaning performance, adjust to the lowest practical setting. If your vacuum is difficult to push, adjust to the next higher setting.

To plug your vacuum in, gently pull the cord out of the automatic cord rewind and stop at the yellow mark on the cord. Do not pull past the red mark. Once you have the desired amount of cord, plug it into the outlet.

When you finish using your vacuum, unplug it from the outlet. Hold onto the plug and press the automatic cord rewind button until it’s fully retracted. If the cord doesn’t fully retract on the first try, pull a little bit of cord out and press the rewind button again.

Empty the tank once it is full.

1. Press the tank release button and pull out to remove the dirt tank.

2. Hold the dirt tank over a trash container. Press the bottom release button to empty. Once empty, close the lid.

3. Twist the cyclone left and pull down to remove it from the tank.

4. Clean the cyclone with warm water and mild detergent. Let the cyclone completely dry before replacing. To replace, fit into place and twist to the right.

5. Once emptied, place the tank back on the vacuum and press firmly until you hear a “click”.

Note: The dirt tank may be washed in warm water with a mild detergent. Make sure it is completely dry before replacing.

Do not operate the vacuum with damp or wet filters or without all filters in place.

1. Press the tank release button and pull out to remove the dirt tank.

2. Remove the foam filter from the lid. Hand wash in warm water and rinse well; mild detergent may be used if desired.

3. Allow the filter to air dry completely before placing it back into the tank lid.

4. Return the tank back on the vacuum and press firmly until you hear a “click.”

1. Twist the gray collar counter-clockwise until the slot appears, then separate the faceplate.

2. Remove the brush roll, belt, and paddle wheel. Inspect for damages and replace if necessary.

3. To reassemble, align two clips on each end of the paddle wheel with the belt on and pop back into place. Place the brush roll with the belt back in. Faceplate will not close properly if all parts are not aligned correctly.

1. Unplug the vacuum, turn over and unscrew six (6) Phillips-head screws to remove the bottom cover. Lift the brush straight out and remove the belt.

2. Clean debris from the brush roll. Inspect by placing on its end and spinning. The brush roll should spin freely, multiple times by one flick. If it doesn’t, replace the brush roll. Check the belt for wear or cuts and replace if necessary.

3. Replace the brush roll and belt by looping the belt over the motor shaft and the brush roll. Line up the end caps and pull the brush forward into place. This will stretch the belt. Return the bottom cover back on and replace the screws.

1. Remove the hose from the back of the vacuum by twisting it to the left. Remove any debris that may have gotten clogged.

2. Check the foot hose on the back of your vacuum down towards the bottom. If necessary, remove the screw from the foot hose and check for clogs.

3. Check the air passageway on the bottom of your vacuum. Remove the bottom cover and the brush. Remove any debris.

The vacuum may be difficult to push due to an incorrect height adjustment. To remedy this, adjust the powerfoot to the correct height setting.