RONIX 8627C (01) PDF Document

The main parts of the RONIX 8627C are:

• Blow Nozzle

• Extension Tube

• Speed Regulator Knob

• ON / OFF Switch

• Motor Housing

• Handle

Read all safety warnings and instructions carefully before starting the RONIX 8627C. These instructions are for your safety and the safety of others. Children, persons with limited physical, sensory or mental abilities, or persons with insufficient experience and knowledge must never be allowed to use the machine. Children are not allowed to play with the device. Cleaning and user maintenance must not be carried out by children.

Before using the RONIX 8627C, follow these preparation steps:

• Use ear protection and protective goggles during the entire time the machine is in use.

• Do not wear loose clothing or jewelry that could be drawn into the suction opening.

• Keep long hair away from the vents.

• Always perform a visual inspection before use to ensure that bolts and other fasteners are secure, the housing is undamaged, and guards are in place.

To connect the blowing nozzle to the lengthening tube on the RONIX 8627C:

1. First, align the gap of the nozzle with the protuberance of the lengthening tube.

2. Press down until the positioning point of the lengthening tube reaches the upper wall of the gap of the nozzle.

3. Secondly, rotate the blowing nozzle clockwise until the positioning point of the extended pipe reaches the snap position of the blowing nozzle.

When connecting the blowing nozzle and the main body, pay attention to the position of holding the main body and the blowing head when connecting.

Press the ON/OFF power switch to start the RONIX 8627C. The product will start from speed I. To adjust the wind speed, use the Speed Regulator Knob. The blower has a III cycle speed control.

There are three ways to use the bent nozzle with the RONIX 8627C:

1. Extension tube + bent nozzle in reverse direction: To blow leaves, debris, or dust from high places.

2. Extension tube + bent nozzle: To blow leaves, debris, or dust from the ground.

3. Only bent nozzle: To blow dust and foreign objects on the working table. Minors can use it to blow away leaves, debris, and dust from the ground.

The concentrating nozzle on the RONIX 8627C can be used as follows:

1. Extension tube + Concentrating nozzle: To blow foreign objects such as dust or spider webs from high places.

2. Extension tube + Concentrating nozzle: To blow leaves, debris, or dust from the ground.

3. Only concentrating nozzle: To blow foreign objects from a working table.

The flat nozzle on the RONIX 8627C can be used in two ways:

• Extension tube + flat nozzle: To blow leaves, debris, or dust from the ground. Using the wide flat nozzle provides more efficiency.

• Only flat nozzle: To blow foreign objects from a working table. Using the wide flat nozzle provides more efficiency.

The inflatable blowing nozzles for the RONIX 8627C can be used to inflate items such as swimming rings, small kayaks, and other similar inflatables.

The RONIX 8627C is designed with a rotation function that allows the handle and body to be optionally installed at up to a 270° angle, making it suitable for different working environments. To adjust the angle, hold the body with one hand and the handle with the other. Rotate the body counterclockwise or clockwise with the hand holding the body to adjust to the desired angle.

To clean the RONIX 8627C, follow these instructions:

• The device must not be sprayed with water or placed in water to avoid the risk of electric shock. Keep the ventilation slots, motor housing, and handles clean. Use a damp cloth or brush for this purpose.

• Do not use cleaning agents or solvents, as this could cause irreparable damage to the device.

• Keep the ventilation slots free of dust and debris to prevent the leaf blower from overheating.

• Clean the blower regularly with a soft cloth, preferably every time you use it. If dirt doesn’t come out, use a soft cloth dampened with soapy water.

• Never use solvents such as gasoline, alcohol, and ammonia water to clean the blower. These solvents can damage the plastic parts.