RONIX 8604 (01) PDF DOCUMENT

The RONIX 8604 includes a clean needle, shoulder strap, viscosity cup, 1 battery, charger, nozzles (1/1.8/2.5mm), and a spanner.

The main parts of the RONIX 8604 are the Lock Button, LED light, Motor, adjustable knob, Dimmer, Air Cap, Trigger, Battery, and Tank.

When using the RONIX 8604, please adhere to the following safety warnings:

– Do not spray flammable or combustible materials near an open flame, pilot lights or sources of ignition such as hot objects, cigarettes, motors, electrical equipment and electrical appliances.

– Keep the area clean and free of paint or solvent containers, rags, and other flammable material.

– Avoid creating sparks from connecting and disconnecting power cords.

– For use with only water-based products with a minimum flash point of 73 °F (22°C). (Flash point is the temperature at which a fluid can produce enough vapor to ignite).

– Always place the sprayer upright (do not place the sprayer upside down or on its side) to prevent liquid from entering internal wiring and causing electric shock.

– Keep the spray area well ventilated. Keep a good supply of fresh air moving through the area.

– When you stop spraying, always unplug the cord to prevent unintended operation.

– Clean the spray gun thoroughly after each use.

– To prevent electrical shock, never immerse the sprayer into water or other liquids.

– When using parts that do not comply with the specifications and safety devices of the manufacturer, the user assumes all risks and liabilities.

To ensure your RONIX 8604 sprayer operates properly, it is important to make sure the paint is suitable for spraying. Follow these steps to thin the paint:

1. Hold the viscosity cup in your hand and block the bottom of the viscosity cup with one finger.

2. Fill the viscosity cup with the diluted paint.

3. Release your finger to let the paint leak out and time it.

4. Refer to the thinning chart to ensure the paint has the correct viscosity.

The RONIX 8604 can be equipped with a 1.0mm, 1.8mm, or 2.5mm nozzle. To change the nozzle:

1. Simply turn the tip counterclockwise with the M4 wrench to loosen.

2. Place the desired nozzle tip on the gun head and then tighten with the M4 wrench.

3. Fix the nozzle with the air cap and big nut to complete the replacement.

1. Make sure the container is empty and dry.

2. Pour thinned paint into the tank, do not exceed the MAX scale mark, and rotate to tighten the tank.

3. Be sure the suction tube is inserted tightly. Position the suction tube based on your spraying direction:

a) If you are going to be spraying in a downward direction, the angled end of the suction tube should be pointing toward the front of the gun.

b) If you are going to be spraying in an upward direction, the angled end of the suction tube should be pointing toward the rear of the gun.

To connect the gun body with the motor:

a) Hold the gun with your hand to align the slot on the gun with the slot on the motor and insert it.

b) Hold the motor handle with your hand, rotate the right hand clockwise 90°.

c) When the gun and host are parallel, it is locked.

To remove the motor:

a) Hold the gun with your hand and press the latch in the direction of the arrow.

b) At the same time hold the motor handle with your hand and rotate it counterclockwise 90°.

c) Pull out to remove the motor from the gun.

To Remove the Battery Pack:

a. Hold the spray gun with your hand and press and hold the button on the battery.

b. Pull out the battery.

How to Use LED Lights:

a) Adjust the position of the LED light.

b) Click the LED switch to turn on the LED light.

c) When not in use, it can be detached and used as a work light.

Hook and Carrying:

A shoulder strap can be hung on the hook located on the tool and used on the shoulder for easy carrying.

Spray Width Adjustment:

The patent spray width adjustment helps you control the spray width according to the spraying environment, reduce waste, and save material.

a) The counterclockwise rotation of the width knob shortens the width.

b) The clockwise rotation of the width knob increases the width.

c) By adjusting the air cap and the width knob at the same time, you will be able to spray a beautiful circular pattern.

Adjust the spray patterns:

The spray pattern shape is adjusted by turning the ears of the air cap to either the vertical, horizontal, or diagonal positions. Test each pattern and use whichever pattern is suitable for your application.

Spray Properly:

1. Keep distance. The best distance for spraying is 8 to 12 inches from the surface you’re spraying. Too far away may result in overspray (and wasted liquid), and too close may cause liquid build-up (runs).

2. The spray result depends heavily on the smoothness and cleanliness of the surface to be sprayed. Therefore, the surface should be carefully prepared and kept free of dust.

3. Cover all surfaces not to be sprayed. Cover screw threads or similar parts of the target object.

4. It is advisable to test the spray gun on cardboard or a similar surface to find the correct setting.

IMPORTANT: Begin spraying outside of the target area and avoid interruptions inside the target area.

CORRECT: Be sure to hold the spray gun at an even distance of approx. 5 – 15 cm to the target object. Move the spray gun evenly cross-wise or up-and-down, depending on the spray pattern setting. An even movement of the spray gun results in an even surface quality.

INCORRECT: Avoid heavy spray fog build-up, which leads to an uneven surface quality.

IMPORTANT: Never store the sprayer longer than 30 minutes without cleaning. Dried by-products act like glue and will cause moving parts to stick. Failure to properly clean your paint sprayer will damage the unit.

STEP ONE: Clean up the gun

1) Unplug the sprayer from the electrical outlet and pull the trigger on the spray gun so material inside the unit flows back into the container.

2) Empty any remaining material from the container.

3) Fill the container approximately 1/2 full with an appropriate cleaning solution. For latex, use warm soapy water; for oil-based, use a cleaning solution recommended by the material manufacturer.

4) Plug the sprayer into an electrical outlet.

5) Press the switch of the sprayer until the cleaning solution passes through the spray nozzle for several seconds.

6) Remove the container and properly discard the cleaning solution.

7) Unplug the sprayer from the electrical outlet.

STEP TWO: Clean up the nozzle tip

1) Unscrew the container and discard any remaining cleaning solution.

2) Remove the suction tube from the sprayer and clean it with warm, soapy water.

3) Unscrew the air cap, remove the nozzle tips. Clean them with warm, soapy water.

4) Let the components dry thoroughly and reassemble the unit.

5) Store the unit.