PYLE PTA1000BTUK (01) PDF Document

When using electrical products, caution should always be used. Please read and keep these safety instructions:

1. Do not use this apparatus near water.

2. Clean only with a dry cloth.

3. Do not block any of the ventilation openings. Install the amplifier in accordance with all manufacturer’s instructions.

4. Do not install near any heat source, such as a radiator, heat register, stove or other apparatus (including amplifiers).

5. Do not alter a polarized plug or grounding-type plug, as they provide protection. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

6. Protect the power cord from being damaged, particularly near the plugs, convenience receptacles and the point where they connect to the amplifier.

7. Only use attachments/accessories provided by the manufacturer.

8. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the amplifier. When a cart is used, use caution when moving to avoid injury from tipping over.

9. Unplug the amplifier during lightning storms or when unused for long periods of time.

10. Refer all servicing to qualified service personnel. Servicing is required when the amplifier has been damaged in any way.

11. Never break off the ground pin and connect only to a proper power supply type, indicated on the unit.

12. If this product is to be mounted on an equipment rack, rear support should be provided.

13. Exposure to extreme high noise levels may cause permanent hearing loss.

The US Government’s Occupational Safety and Health Administration (OSHA) has specified the following permissible noise level exposures to prevent hearing loss. To ensure against potentially dangerous exposure to high sound pressure levels, it is recommended that all persons exposed to equipment capable of producing high sound pressure levels, such as this amplification system, be protected by hearing protectors while this unit is in operation.

INPUT GAIN (dB): These controls are used to adjust the input gain of each channel. They determine how loud each channel of the power amplifier will sound for a given input signal level. The maximum input gain is achieved by turning the control completely clockwise. Turning the control counter-clockwise will yield lower system noise. Turning the control fully counter-clockwise turns this setting OFF.

POWER SWITCH: This heavy-duty, rocker-type switch turns on the power to the amplifier. When the unit is turned on, there is a three-second delay, which reduces/eliminates the turn-on transients associated with the system equipment connected to the amplifier and protects loudspeakers.

LEVEL INDICATOR: Channel A and Channel B level LED indicator.

BT/AUX IN BUTTON SWITCH: Press to switch to Wireless BT mode. Unpress for AUX mode.

Wireless BT ANTENNA: This is the Wireless BT receiver antenna for better signal.

AUX INPUT JACKS: Connect AUX input to these jacks.

POWER LED (POWER): These indicators illuminate when the AC main power is being supplied to the amp and both channels are operational. If either channel experiences faulty conditions, exceeds safe operating temperature limits, or if the main circuit breaker trips, then both channel power LEDs will be dark, indicating shutdown. If the BRIDGE mode is selected, the PWR indicator on channel B will remain dark as a positive indication of this mode selection.

SIGNAL ACTIVITY LEDS (SIGNAL): These indicators illuminate when the associated channel output signal level exceeds 1 Volt RMS.

OVERLOAD LEDS (CLIP): These indicators illuminate when the associated channel has been overloaded.

FAULT LEDS (FAULT): These indicators illuminate when the amplifier has just been turned ON or if the amplifier has detected a problem, such as overheating or circuit problems.

The digital MP3 player on the PYLE PTA1000BTUK has the following features and controls:

Features:

• Support USB SD Card

• Music format: Mp3, WMA, WAV

• Connect via Wireless BT, Compatible Wireless BT: version 5.0

• With LCD display, shows ID3 format.

• FM: 87.0 – 108MHz

• 6 Preset digital EQ effect.

USB, SD, Wireless BT/FM mode Controls:

• ►►I: Forward/Next channels

• ►II: Play/Pause/Scan

• ◄◄: Reverse/Previous channels

• RPT: SD/USB repeat Play

1. Press the MODE key to select FM radio mode.

2. Press the ►II key once. It will begin to scan the FM frequency range and set P1 to P30 stations.

3. Press the ◄◄ or ►►I key to select the desired stations, or use the track select key (1 to 30) to get the desired stations.

External devices which have a built-in Wireless BT feature can be connected to the PYLE PTA1000BTUK amplifier wirelessly to play through the amplifier’s speakers.

1. At first be sure that the amplifier is powered ON, and turn the volume to the MINI position. It’s better to pull the Wireless BT Antenna on the back panel for better receiving.

2. Press the BT/line button switch in on the front panel, you will hear the voice “POWER ON” and also “PAIRING”, and then the unit is automatically ready to pair with your external device.

3. Turn ON the Wireless BT of your external devices like a Smartphone, Computer, etc.

4. Search for available Wireless BT devices within range of your external device and wait for your device to select “PYLE PRO” on the pairing devices lists.

5. Seconds later, when you hear a voice “Your Device is Connected”, the Wireless BT pairing is successful.

6. You can now play music on your external device through the amplifier.

1. INPUT: Cannon and input jack connectors provide balance or unbalance input mode.

2. MODE SWITCH: This switch is used to select STEREO or BRIDGE mode operation.

3. GROUND LIFT SWITCH: Used to lift the ground connection.

4. BINDING POST OUTPUTS: Shockproof binding posts are provided. For each channel, the outputs are in parallel and the speaker connection cables can be terminated with banana plugs or stripped wires.

5. SPEAKER OUTPUT: The amplifier provides (3) four-conductor speaker connectors, one for each channel and one for bridge mode.

6. POWER SELECT: Switch to choose 110V-120V or 220V-240V power supply.

7. POWER INPUT: This is a standard IEC power connector. An AC main cord, which has the appropriate AC plug and rating for the intended operating voltage, is included in the carton.

8. FAN GRILL: (Two) 2-speed DC fans supply cool air to the amplifier. The fans switch to high speed automatically when the unit requires additional cooling.

9. FM ANTENNA: Connect for tuner antenna.

If your PYLE PTA1000BTUK has no power, please check the following:

• Ensure the power cord is securely connected.

• Plug a different device into the electrical outlet to verify that the outlet is working correctly.

If there is no sound from your amplifier, try these solutions:

• The wrong input was selected on the amplifier.

• The music master volume control is set to minimum.

• The fuse may be defective.

• Speakers and speaker cables are either not connected, loose, or malfunctioning.

If you are getting no sound from your microphone, check the following points:

• The microphone is not turned on.

• The microphone cable is either loose or not functioning.

• The microphone volume for that channel is set to minimum.

• The microphone is not functioning correctly.

To fix severe hum or noise, please follow these steps:

• Ensure all cables and wires are securely connected.

• Connect a different source device to see if the buzzing persists. If it does not, the problem may be with the original device.

• Connect your device to a different input on the amplifier.

• The volume may be set too high, causing the loudspeakers to distort.

• 2-Channel Pro Audio Amplifier

• Bridgeable Amp: Bridge Mode Ability

• Built-in Wireless BT Streaming

• (2) 1/4″ TRS Input Connector Jacks

• (2) XLR Input Connector Jacks

• (3) SpeakOn Output Connectors (AIB/Bridged)

• (2) Pair Speaker Terminal Binding Post Connectors

• Power, Protect, Clip, Signal LED Indicators

• Left and Right Channel Level Signal Indicators

• Built-in Ventilation Cooling Fans

• Front Panel Control Center

• Rack-Mountable System

• Simple & Hassle-Free Pairing

• Instant Wireless Audio Streaming Ability

• Works with All of Today’s Latest Wireless BT Devices

• Wireless BT Network Name: ‘PYLE PRO’

• Wireless BT Version: 5.0

• Wireless Range: Up to 30’+ ft.

The box contains:

• Pro Audio Amplifier

• Power Cable

• BT and FM Antenna

• Power Output: 2000 Watt MAX

• Amplifier Type: 2-Channel

• 2x 1000 Watt @ 4 Ohm

• 2x 500 Watt @ 8 Ohm

• Distortion: <1.0%

• Input Level: +4dB

• Signal/Noise Ratio: 102dB

• Frequency Response: 20Hz – 20kHz, +/- 0.2dB

• Power Supply: 120/220V, Switchable

• Dimensions (L x W x H): 19.09″ x 9.84″ x 3.54″ -inches (48.4 x 24.9 x 8.99 -cm)