MIDEA MRM33S9ASL (01) PDF Document

The MIDEA MRM33S9ASL requires a 115 Volt, 60 Hz, AC only, 15-amp fused, grounded electrical supply. It must be plugged into a grounded 3-prong outlet. Do not use an adapter or an extension cord. It is recommended that the refrigerator be plugged into an electrical circuit serving only this appliance and into an outlet that cannot be turned off with a switch or pull chain.

To ensure efficient operation and adequate air circulation, the MIDEA MRM33S9ASL requires the following clearance:

4 inches (10 cm) of clearance at the back and both sides of the refrigerator.

10 3/4 inches (30 cm) of clearance at the top.

If you place the MIDEA MRM33S9ASL next to a fixed wall, allow sufficient space on the hinge-side for the door to swing open.

Leveling the MIDEA MRM33S9ASL is important for proper operation and to avoid cooling, frost, and moisture problems that can occur when the door does not close properly. Follow these steps:

1. Move the MIDEA MRM33S9ASL to its final location.

2. Place a carpenter’s level on the top of the refrigerator cabinet.

3. Adjust the two leveling feet, located at each of the two front corners of the cabinet, until the refrigerator is level. The leveling feet are easier to adjust if you have someone push against the top front of the refrigerator to take some weight off the feet.

To raise the MIDEA MRM33S9ASL, turn the leveling feet clockwise. To lower it, turn them counterclockwise.

Before plugging in the MIDEA MRM33S9ASL, allow it to stand upright for approximately 2 hours. This reduces the possibility of a malfunction in the cooling system from improper handling during transportation. Additionally, wash the interior using a soft cloth dampened with a baking soda solution (2 tablespoons baking soda mixed with 1 quart of warm water), and then dry all surfaces thoroughly with a soft cloth.

The temperature controls for the MIDEA MRM33S9ASL are located inside the unit. Start with the controls at the midpoint (4) setting. To make the refrigerator cooler, turn the knob toward 6. To make it less cold, turn the control toward 1. To turn the MIDEA MRM33S9ASL off, turn the control to OFF. The refrigerator will not cool when the control is set to OFF.

Defrost the MIDEA MRM33S9ASL when ice in the freezer compartment becomes too thick. Follow these steps:

1. Turn the refrigerator control to OFF and unplug the MIDEA MRM33S9ASL.

2. Remove all food and store it in a cooler with ice, in another refrigerator, or in a cool area.

3. Ensure the drainpipe is clear. Use a soft cloth to clean the refrigerator liner.

4. Place the drain tray under the evaporator to catch melting ice. Empty it as necessary.

5. Keep the refrigerator door open until the ice melts. You can place a pan of hot water in the freezer to speed up the process.

6. Use a plastic scraper to help remove ice and frost. Do not use an ice pick or other metal or sharp implement, as this may damage the MIDEA MRM33S9ASL.

7. Once the ice has melted, dry the interior with a soft cloth.

8. Plug in the MIDEA MRM33S9ASL and turn the controls to the desired setting. When the refrigerator has cooled, return the food.

To improve the efficiency of your MIDEA MRM33S9ASL, consider these tips:

Allow hot foods to cool to room temperature before placing them in the MIDEA MRM33S9ASL.

Avoid overloading, as it forces the compressor to run longer.

Wrap foods properly and wipe containers dry before placing them in the MIDEA MRM33S9ASL to cut down on frost build-up.

Do not line storage shelves with aluminum foil, wax paper, or paper toweling, as these interfere with cold air circulation.

Organize and label food to reduce door openings and extended searches.

Do not add a large amount of unfrozen food to the MIDEA MRM33S9ASL at one time.

If your MIDEA MRM33S9ASL does not operate, check the following:

Ensure the power cord is fully plugged into the electrical outlet.

Check the house fuse or circuit breaker box and replace the fuse or reset the circuit breaker if needed.

If there is a power failure, the refrigerator turns off. Wait until the power is restored.

If the door of the MIDEA MRM33S9ASL does not close completely, check the following:

Check for food packages that are interfering with the door and move or remove them.

Clean the door gaskets if they are dirty.

Ensure the MIDEA MRM33S9ASL is level.

If the food in your MIDEA MRM33S9ASL is not cold, consider the following:

Ensure the door is not opened too often and is closed properly.

If a large amount of food was recently added, allow time for it to cool.

Check the door gasket and food distribution to ensure the door closes completely.

If the MIDEA MRM33S9ASL was disconnected for a period, allow 4 hours for it to cool completely before adding food.

Set the temperature control to a colder setting if it is set too warm.

The specifications for the MIDEA MRM33S9ASL are: