LD SYSTEMS MAILA SAT LDMAILASAT (01) PDF Document

Please follow these safety instructions when using the LD SYSTEMS MAILA SAT LDMAILASAT:

1. Please read these instructions carefully.

2. Keep all information and instructions in a safe place.

3. Follow the instructions.

4. Only use the accessories in the manner intended.

5. Do not open or modify the product.

DANGER OF SUFFOCATION! KEEP AWAY FROM CHILDREN! THE PRODUCT CONTAINS SMALL PARTS THAT CAN BE SWALLOWED AND PACKAGING MATERIAL THAT CAN BE SWALLOWED! PLASTIC BAGS MUST BE KEPT OUT OF REACH OF CHILDREN!

The LD SYSTEMS MAILA SAT LDMAILASAT is a device for professional audio installation. It has been developed for professional use in the field of audio installation and is not suitable for use in households. Furthermore, this product is only intended for qualified users with specialist knowledge of dealing with audio installations.

Use of the product outside of the specified technical data and operating conditions is considered improper use. Liability for damage and third-party damage to persons and property due to improper use is excluded.

The product is not suitable for:

• People (including children) with reduced physical, sensory or mental abilities or lack of experience and knowledge.

• Children (Children must be instructed not to play with the device).

Included in the scope of delivery of the LD SYSTEMS MAILA SAT LDMAILASAT are:

• 1x LD MAILA SAT Satellite

• Operating instructions

Please check the completeness and integrity of the delivery and notify your distributor immediately after purchase if the delivery is not complete or damaged.

To mount the LD SYSTEMS MAILA SAT LDMAILASAT satellite speaker (on a loudspeaker column MAILA COL, amplifier module MAILA SPA, or another satellite MAILA SAT), follow these steps:

1. Slide the satellite speaker from behind onto the element below as far as it will go.

2. Make sure that the two guide rails of the satellite are correctly inserted into the grooves on the top of the element below to ensure a tight fit and to establish the connection of the electrical contacts of both elements.

3. The locking system must engage correctly, and the release button of the underlying element must form a level surface with the corresponding enclosure component. If the locking system is not correctly engaged, a red mark is visible in the guide bush of the release button.

4. Proceed in the same way to add more satellites to the system.

To dismantle a satellite, press the release button of the element underneath and pull the satellite backwards by the handle.

To adjust the angle of spread on the LD SYSTEMS MAILA SAT LDMAILASAT, turn the handle of the satellite to set the desired spread angle. The set angle is indicated by a scale printed on the side.

The LD SYSTEMS MAILA SAT LDMAILASAT satellites do not need to be secured by a safety rope, as the SmartLink+ connection meets the criteria for inherent safety.

However, there are two M8 threads on the back of the satellite speaker that can be used for securing if desired. To do this, remove the inserted blind screw with the aid of a suitable tool and use a suitable eyebolt and securing rope.

1. Packaging can be fed into the recycling system via the usual disposal channels.

2. Please separate the packaging according to the disposal laws and recycling regulations in your country.

1. This appliance is subject to the European Directive on Waste Electrical and Electronic Equipment as amended (WEEE Directive). Old appliances and batteries do not belong in household waste. The old appliance or batteries must be disposed of via an approved waste disposal company or a municipal waste disposal facility. Please observe applicable regulations in your country.

2. Observe all disposal laws applicable in your country.

3. As a private customer, you can obtain information on environmentally friendly disposal options from the dealer from whom the product was purchased or from the relevant regional authorities.

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.