JETSON JUPITER JJUP2-TEL (01) PDF Document

Before using the JETSON JUPITER JJUP2-TEL, please read and accept all safety instructions. The user is responsible for any loss or damage caused by improper use.

Rider and Usage Restrictions:

• The rider should not exceed 132 lb.

• Adult supervision is required.

• This product should not be used by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.

• Persons with heart conditions, pregnant women, persons with head, back, or neck ailments, or prior surgeries to those areas, and persons with any mental or physical conditions that may make them susceptible to injury should be cautioned not to operate.

• The product cannot be ridden by more than one person.

• Do not perform racing, stunt riding, or other maneuvers, which may cause loss of control.

Safe Operating Practices:

• Always wear appropriate protective equipment, including a helmet with appropriate certification, knee pads, and elbow pads.

• Always wear shoes and keep shoelaces tied. Never operate the product barefooted.

• Make sure your feet are always placed securely on the deck.

• Avoid sharp bumps, drainage grates, and sudden surface changes. Avoid streets and surfaces with water, sand, gravel, dirt, leaves, and other debris. Wet weather impairs traction, braking, and visibility.

• Do not ride at night. Do not ride after drinking or taking prescription medication.

• Do not carry items when riding.

• Always give way to pedestrians and be alert to things in front and far away from you.

• Do not allow distractions like answering the phone.

• When riding with others, always keep a safe distance to avoid a collision.

• When turning, be sure to maintain your balance.

Brake Safety:

• The brake may become hot while operating; do not touch it with your bare skin.

• Applying brakes too hard or too suddenly can lock up a wheel, which could cause you to lose control and fall. Sudden or excessive application of the brake may result in injury or death.

Battery Safety:

• Do not mix old and new batteries.

• Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries.

Environmental Note:

• Prolonged exposure to UV rays, rain, and the elements may damage the enclosure materials; store indoors when not in use.

Before each cycle of operation, the operator shall perform the preoperation checks specified by the manufacturer:

• That all guards and pads originally supplied by the manufacturer are in their proper place and in serviceable condition.

• That the braking system is functioning properly.

• That any and all axle guards, chain guards, or other covers or guards supplied by the manufacturer are in place and in serviceable condition.

• That tires are in good condition, inflated properly, and have sufficient tread remaining.

• The area that the product is to be operated should be safe and suitable for safe operation.

• Check whether all safety labels are in place and understood before riding.

• Replace any worn or broken parts immediately.

No. Do not attempt to disassemble, modify, repair, or replace the unit or any components of the unit without instruction from the Jetson Care Team. This will void any warranty and can lead to malfunctions which may cause injury.

The battery may contain hazardous substances which could endanger the environment and human health. The symbol marked on the battery and/or packaging indicates that the used battery shall not be treated as municipal waste. Batteries should be disposed of at an appropriate collection point for recycling. By ensuring the used batteries are disposed of correctly, you will help prevent potential negative consequences for the environment and human health. The recycling of materials will help to conserve natural resources.

• Weight Limit: 132 LBS

• Product Weight: 6 LBS

• Wheel Size: 4″

• Folded Dimensions: 24″ (L) × 10.5″ (W) × 8.5″ (H)

• Unfolded Dimensions: 24″ (L) × 10.5″ (W) × 29″ (H)

• Deck Dimensions: 17.5″ (L) × 3.5″ (W)

• Handlebar Height: 29″ – 34″

• Batteries: 3 AA Batteries Required (Not Included)

• Recommended Age: 5+

• Features: LED Light-Up Wheels, Deck, & Stem; Easy Folding Technology

• Remove all protective packaging pieces prior to beginning assembly, including the packaging at the top of the stem.

• The directions (right, left, front/forward, and rear/back) are oriented as the rider would see them when standing on the scooter. For example, the “right side” is where the rider’s right hand will be.

• Adults must assist children in the assembly and initial adjustment procedures of the product.

• Keep small parts away from children during assembly.

• Frequently inspect the product for damage.

To unfold the scooter for assembly and riding, or fold it for storage and transport, follow these steps:

1. Holding the locking latch steady with one hand, use the other hand to loosen the knob by turning it counterclockwise for 2-3 rotations.

2. Pull open the locking latch.

3. Pull the folding lever up towards the top of the stem. Hold it there while you raise the stem upright (to unfold) or lower the stem towards the deck (to fold).

4. Ensure that the stem “clicks” into place in the folded or unfolded position.

5. Release the folding lever.

6. Hold the locking latch steady with one hand while you tighten the knob by turning it clockwise.

7. Push the locking latch closed.

8. Check that the stem is secure.

IMPORTANT: Never ride without the stem clicked into the upright position and the locking latch closed and tight.

If you cannot open or close the locking latch, the knob may be too tight. Loosen the knob by turning it counterclockwise for 1/2 rotation at a time until you can utilize the latch.

1. Unfold the scooter so that the stem is upright.

2. Unscrew the pre-attached bolt from the nut in the stem by turning it clockwise with the screwdriver tip of the 2-bit tool. You may need to hold the nut steady with a finger. Set the hardware aside.

3. Position the handlebar base over the top of the stem such that the raised line on the inside of the handlebar base is in line with the indented channel on the top of the scooter stem.

4. Slide the handlebar onto the scooter stem.

5. Push down and adjust until the holes in the sides of the handlebar base are aligned with the holes on the sides of the stem.

6. Insert the bolt through the aligned holes on the right-hand side of the handlebar until the end is visible through the left-side holes. (The right side is determined when facing the front of the scooter from the riding position).

7. Place and hold the nut at the end of the bolt in the aligned holes on the left side of the handlebar.

8. Tighten the bolt into the nut by turning it clockwise with the screwdriver tip of the 2-bit tool.

9. Check that the handlebar is secure.

IMPORTANT: Prior to every ride, check that the bolt and nut are tightened and secure.

1. Open the stem clamp latch.

2. Loosen the bolt opposite the latch to widen the clamp by turning it counterclockwise with the Allen key tip of the 2-bit tool.

3. While pressing in the stem pin, lift or lower the handlebar until the pin clicks into another stem pin hole.

4. Close the stem clamp latch and tighten the bolt by turning it clockwise with the Allen key.

5. Check that the handlebar is secure.

IMPORTANT: The stem pin alone will not keep the stem secure. Make sure the stem clamp is tightened and closed before riding.

If you cannot open or close the latch, the bolt on the clamp may be too tight. Loosen the bolt 1/2 rotation at a time until you can utilize the latch.

You will need 3 AA batteries (not included) to use the lights.

1. Loosen and remove the screw securing the battery compartment cover on the underside of the deck by turning it counterclockwise with the screwdriver tip of the 2-bit tool.

2. Lift and remove the battery compartment cover.

3. Place 3 AA batteries in place according to the +/- directions indicated inside the battery compartment.

4. Replace the battery compartment cover.

5. Re-insert the screw and tighten it by turning it clockwise with the screwdriver.

6. Check that the compartment cover and screw are secure.

1. Place one foot on the front of the deck facing forward.

2. Use the back foot to push off the ground and propel the scooter forward.

• To Coast: Place the kicking foot on the deck behind the front foot at a slight angle.

• To Make Turns: Rotate the handlebar to the left or right.

Press down gently with the rear riding foot on the rear foot brake to slow down. Apply more pressure to come to a complete stop.

• Wheel Lights: The lights on the wheels are motion-activated and will illuminate when they rotate, even if the other lights are not powered on.

• To Turn On Deck and Stem Lights: Quick-press the lighting control button on the underside of the deck.

• To Change the Lights: Cycle through 7 different lighting patterns by quick-pressing the button again. Stop pressing when you’ve landed on the lighting pattern that feels right for your ride.

• To Turn Off the Lights: The 8th quick-press will turn off the lights. To power off the lights without going through the cycle of patterns, press and hold the lighting control button for 3 seconds.

IMPORTANT: To preserve battery power, turn the lights off when you’re finished riding the scooter.

A helmet should be worn by the rider at all times while on the scooter. Wear an ASTM F1492 approved helmet.

• Proper Positioning: The forehead is covered by the helmet.

• Improper Positioning: The forehead is exposed. A fall could result in serious injury.

To clean the scooter, carefully wipe with a damp cloth and then dry with a dry cloth. Do not apply water directly to the scooter. Water can cause damage to the electrical system or to the frame deterioration, which could lead to a malfunction that puts rider safety at risk.

• Keep away from fire and excessive heat.

• Avoid intense physical impact and/or severe vibration.

• Ride the scooter on a smooth, flat surface.

• Protect from water or moisture.

• Store the scooter indoors and in a dry place.

• Cover the scooter to protect it against dust.

• Remove batteries prior to storing the scooter for extended periods of time.