CASA SYSTEMS PEBBLE (01) PDF MANUAL

CASA SYSTEMS PEBBLE (01) PDF SUMMARY:

How do I connect the Pebble unit to the network?

The Pebble unit can connect via an Ethernet or Wi-Fi connection. The Ethernet connection is plug-and-play, while the Wi-Fi connection requires setup.

How do I set up an Ethernet connection?

1. Connect the GPS antenna cable to the GPS port on the Pebble unit.
2. Position the GPS antenna puck near a window for a clear view of the sky.
   • Warning: The Pebble unit will not connect to the LTE network if the GPS antenna fails to lock on its location.
3. Connect the Ethernet cable to the WAN (Ethernet) port on the Pebble unit.
4. Connect the other end of the Ethernet cable to a LAN port on the home router or the Ethernet outlet that has service.
5. Plug in the Pebble unit power supply.

How do I set up a Wi-Fi connection?

1. Connect the GPS antenna cord into the GPS port on the back of the unit.
2. Position the GPS antenna puck near a window for a clear view of the sky.
3. Connect the power supply to the DCIN port on the Pebble and plug it in.

How do I install the Wi-Fi connection using Sprint Set Up Assistant?

1. Download the Sprint Set Up Assistant app from the App/Play store on your mobile device or tablet. Select Pebble from the three product options available then follow the prompts.
2. In the Set Up Assistant app, follow instructions to move to Settings and select the Pebble Wi-Fi connection then click Continue.

How do I configure Pebble Wi-Fi?

1. In your phone settings, connect to the Wi-Fi named “Sprint-Pebble-XXXX” and return to the Set Up Assistant app and follow prompts.
2. The app will pair with your Pebble and present the option to configure Wi-Fi backhaul using your home router. Click Configure.
3. Select your home Wi-Fi router (5Ghz preferred over 2.4Ghz) from the list.
4. Enter the password (case sensitive) for your home Wi-Fi router then click Connect.
5. When prompted, click Continue to set up Wi-Fi backhaul.
   • Note: This process will take 8 to 10 minutes to complete. The app will provide prompts to continue with the Wi-Fi configuration for the Pebble.
6. The app provides a progress bar to indicate the status of the Backhaul setup. Once the installation is complete click Continue.

How do I use the Application Dashboard?

1. Open the application and click Dashboard.
2. The Dashboard provides information for the Pebble units.
3. From the Dashboard, click My Device to display information on the Pebble model.
4. From the Dashboard, click Network Settings to display network details. Click Ethernet or Wi-Fi to display specific network details. Click Change to change network settings.
5. From the Dashboard, click Device Status and click LTE to display status information on the Pebble LTE settings.
6. From the Dashboard, click Device Status and click GPS to display status information on the GPS settings.

How do I reset the Pebble?

The manual Pebble reset button supports the following reset behavior:

• 1 second short-press reset to reboot both Wi-Fi and LTE
• 10 second long-press reset to factory reset both Wi-Fi and LTE

The Pebble can also be reset using the Set Up Assistant app functions from My Device on the Dashboard and following the prompts:

1. Select Factory Data Reset to clear all configuration of the Pebble.
2. Select Reset to continue the process.
3. Wait while the device is resetting.
4. Press OK to complete the reset process.

What is the Pebble status and LED behavior for Wi-Fi and Ethernet?

• Device Startup: fixed red LED
• Device Activating: blinking blue LED
• Activation Complete: fixed green LED
• Device in Use: blinking green LED
• Error Condition: blinking red LED (check that the GPS puck is near a window)
• Factory Data Reset: [no LED behavior given]
• Factory Data Reset Successful: [no LED behavior given]