LARQ PITCHER PUREVIS (01) PDF Document

The main components of the LARQ PITCHER PUREVIS are:

1. Fill flap

2. Lambda Λ button

3. Charging pins

4. Hopper

5. LARQ Filter

6. PureVis™ Wand

To get started with your LARQ PITCHER PUREVIS, follow these steps:

1. Remove the PureVis™ Wand from the pitcher. Give your LARQ Pitcher PureVis™ a good wash before use.

2. Wake up your pitcher by charging the PureVis™ Wand. Connect the magnetic charger to the gold charging pins on top of the PureVis™ Wand. A full charge is recommended to start.

3. Remove the filter from its packaging and soak it in water for 10 minutes before first use.

4. Install the filter into the reservoir and put the filter lid on, ensuring it snaps into place. Press the Λ button for 5 seconds to let the pitcher know you are installing a new filter (the indicator light will turn white for 5 seconds followed by a flash of blue light). Fill the reservoir with tap water and pour out the first batch.

5. The PureVis™ Mode will automatically activate after the pitcher is completely filled. A blue breathing light indicates that the pitcher is on as water is filtered through. You can also manually activate a 30-second PureVis™ cycle by pressing the Λ button.

6. Pour yourself a glass of water and enjoy.

You may notice some black carbon dust in the water on your first use or after a prolonged period of not using the LARQ PITCHER PUREVIS. This is harmless carbon from the plant-based filter media. If desired, you can simply run a batch of water through the filter and pour it out.

The LARQ PITCHER PUREVIS has two main modes for the PureVis™ Wand:

PureVis™ Mode: Indicated by a breathing sky blue light. This mode is activated automatically when the pitcher is filled or by a single press of the Lambda button.

Self-cleaning Mode: Indicated by a breathing sky blue light. This mode activates automatically every 6 hours for 60 seconds to keep the pitcher clean.

The filter life notifications on your LARQ PITCHER PUREVIS indicate the following:

<20% filter life remaining: The orange light will flash 3 times prior to PureVis™ Mode. This is a reminder to order a replacement filter.

0% filter life remaining: A solid orange light will appear for 5 seconds prior to PureVis™ Mode. You should swap out the filter for a new one.

After a new filter is installed, hold down the Λ Lambda button for 5 seconds. The indicator light will turn white for 5 seconds, followed by a flash of blue light, to confirm the reset.

To check the filter life, simply activate PureVis™ Mode with a single press of the Λ Lambda button. The light indicator will signal the current filter status.

The battery status lights on the LARQ PITCHER PUREVIS indicate the following:

Breathing green light: The device is charging.

Steady green light: The device is fully charged.

Flashing green light: The battery is low. It will flash twice before a cleansing mode.

Red solid light or flashing purple light: This indicates that something is wrong.

We recommend washing the LARQ PITCHER PUREVIS every 2-3 months when you need to replace the filter.

Before washing the pitcher, remove the PureVis™ Wand. Hand wash the Wand separately with mild soap and warm water. The PureVis™ Wand is completely waterproof but should not be put in the dishwasher.

It is also recommended to give the PureVis™ Wand a full charge every time you replace the filter.

Yes, the LARQ PITCHER PUREVIS is dishwasher-safe. However, smaller parts like the lid, hopper, and filter lid should be placed in the top tray of the dishwasher. The PureVis™ Wand is NOT dishwasher-safe and must be handwashed only.

Please follow these safety instructions:

Unplug the magnetic charging cable when not in use and store it away from metal objects.

This appliance is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.

Children should be supervised to ensure that they do not play with the appliance.

The PureVis™ Wand should be used exclusively with the LARQ PITCHER PUREVIS.

The appliance must only be supplied at safety extra low voltage corresponding to the marking on the appliance.

This appliance contains batteries that are non-replaceable.

Do not charge with any magnetic charger other than the charger cable provided with your LARQ PITCHER PUREVIS.

The PureVis™ Wand contains a rechargeable lithium-polymer battery that must be disposed of properly. Do not allow the wand to come into contact with fire. Contact your local town or city officials for battery disposal information.

Only remove the battery when you intend to discard the product. Ensure the battery is empty of charge before removal and do not use sharp objects. Follow these steps:

1. Take a pair of tweezers and pry off the silicone button pad.

2. Remove the plastic button cover.

3. Remove the button board connection.

4. Pull out the inner bracket, removing the entire inner component from the outer casing.

5. Remove the LED board connection.

6. Unscrew the two screws of the control board.

7. Turn over the control board and pull out the battery connector (red, white & black wires).

8. Remove the holding pads and remove the battery.

9. Remove the sensor connection to complete battery removal.

Caution: Ultraviolet radiation. Do not look at light directly. Direct UV light can irritate eyes and skin. Do not operate the PureVis™ Wand outside the LARQ PITCHER PUREVIS.

Do not use the PureVis™ Wand as a light source.

Only use the LARQ PITCHER PUREVIS with potable water.

Do not operate the PureVis™ Wand in containers such as laboratory beakers.

The PureVis™ Wand’s UV-C light is not intended to disinfect water in the upper chamber or exterior surfaces of the pitcher where the light does not reach.

This product is not intended for use by children.

As with any water treatment system, you should always have a backup method available.

Do not open, expose, modify or touch internal circuitry as this can lead to electric shock. Unauthorized modifications may void the user’s authority to operate this equipment.

Do not allow impact to the UV-C light. If the PureVis™ Wand or UV-C light lens is cracked, chipped or damaged, do not operate.

To cancel a purifying cycle, first press the Λ Lambda button on top of the PureVis™ Wand, then safely remove the PureVis™ Wand from the LARQ PITCHER PUREVIS.