KOGAN KALKTVSTNBA (01) PDF Document

Before beginning assembly of your KOGAN KALKTVSTNBA, please follow these safety guidelines:

• Read all instructions thoroughly before beginning assembly.

• Exceeding the rated weight limit (including the TV, screws, and all attached hardware and components) may result in instability and possible injury.

• This product is designed for installation on wood stud walls, solid concrete walls, or brick walls.

• For indoor use only. Outdoor use may lead to product failure and injury.

• This product contains small parts that may pose a choking hazard if swallowed. Keep all small components and packaging materials away from young children.

• This product is not a toy. Do not allow children to play near the stand without direct supervision.

• The wall or mounting surface must be capable of supporting the combined weight of the stand and TV. If it is not, the structure must be reinforced.

• It is highly recommended to use the supplied wall anchoring kit to prevent the stand from toppling. Failure to anchor the product may result in damage to the product or property, serious injury, or death.

• Use appropriate safety gear, safe working methods, and proper tools. A minimum of 2 people is required for installation. Failure to follow these guidelines may result in property damage, serious injury, or death.

• Inspect all joints every 3 months and re-tighten any loose screws before continued use.

The weight ratings for the KOGAN KALKTVSTNBA stand differ based on the floor surface:

• Normal Floor: 32kg (70.4lbs) RATED

• Glossy Floor: 25kg (55lbs) RATED

Children have died from furniture toppling over. To help prevent tip-over with your KOGAN KALKTVSTNBA stand:

• NEVER allow children to stand, climb or hang on TV stands.

• Ensure the TV is properly anchored to the TV stand before use around children by using the supplied wall anchoring kit.

The KOGAN KALKTVSTNBA studio stand comes with the following components and hardware:

Components:

A (x2) – Side Legs

B (x1) – Back Leg

C (x1) – Lower TV Bracket

D (x1) – Upper TV Bracket

E (x1) – Center Pole Assembly

F (x1) – Anti-toppling Strap

G (x2) – Cable Clips for TV Bracket

H (x2) – Not specified in image label, appears to be part of the pole

I (x2) – Cable Clips for Legs

Hardware:

J (x2) – Screw

K (x1) – 2mm Allen Key

L (x1) – 4mm Allen Key

M (x4) – Anti-toppling Screw

N (x4) – Wall Anchor

M-A (x4) – M5x14 Bolt

M-B (x4) – M6x16 Bolt

M-C (x4) – M6x30 Bolt

M-D (x4) – M8x30 Bolt

M-E (x4) – M8x50 Bolt

M-F (x4) – Bracket (Washer)

M-G (x8) – Small Spacer

M-H (x8) – Large Spacer

Step 1: Assemble the Legs

Attach the two side legs (A) and the back leg (B) to the base of the center pole assembly (E).

Step 2: Set the Height

Adjust the pole to your desired height. The recommended distance from the top of the pole to the locking collar is between 50-150mm. Secure the locking collar firmly before attaching the TV screen.

Step 3: Prepare the TV Brackets

Attach the swivel mechanism to the lower TV bracket (C) and tighten the screw.

Step 4: Attach Brackets to the TV

Place your TV face down on a soft surface. Attach the upper bracket (D) and the lower bracket (C) to the VESA mounting holes on the back of your TV. Use the appropriate bolts (M-A, M-B, M-C, M-D, or M-E) and spacers (M-G, M-H) if needed to ensure a secure fit. Ensure the cable clips (G) are attached to the upper bracket during this step.

Step 5: Mount the TV onto the Stand

With at least two people, carefully lift the TV and hook the mounting brackets onto the top of the center pole. Once the TV is resting on the pole, secure the locking mechanism on the lower bracket to fix the TV in place.

Step 6: Manage Cables

Use the leg cable clips (I) and screws (J) to attach them to the back of the stand’s legs. Route the TV’s power and AV cables through the clips for a clean and tidy setup.

Step 7: Final Adjustments

The stand allows for a ±180° swivel. Adjust the TV to your desired viewing angle. Ensure the TV screen does not touch the aluminum plate where the legs connect.

Step 8: Install the Anti-Toppling Kit

This step is highly recommended for safety. Attach one end of the anti-toppling strap (F) to the upper VESA mounting holes on the back of the TV. Drill holes in the wall at a height between 1100-1350mm. Insert the wall anchors (N), then secure the other end of the strap to the wall using the anti-toppling screws (M).

The dimensions for the KOGAN KALKTVSTNBA are as follows:

• Total Height: 1385mm

• Footprint Width: 880mm

• Footprint Depth: 420mm

• Pole Diameter: Ø35mm

• Horizontal Bracket Length: 644mm

• Vertical Distance Between Brackets: 600mm

• Horizontal VESA Compatibility: Minimum 100mm to Maximum 600mm

• Vertical VESA Compatibility: Minimum 100mm to Maximum 400mm

• Swivel Range: ±180°