KOGAN KALKTVSTNDA (01) PDF Document

Before assembling and using the KOGAN KALKTVSTNDA, please adhere to the following safety warnings:

• Read all instructions thoroughly before beginning assembly.

• Do not exceed the rated weight limit, which includes the TV, screws, and all attached hardware and components. Doing so may cause instability and possible injury.

• This product is designed for installation on wood stud walls, solid concrete walls, or brick walls. The mounting surface must be able to support the combined weight of the stand and TV. If it is not, the structure must be reinforced.

• The stand is for indoor use only. Outdoor use can lead to product failure and injury.

• This product contains small parts that can be a choking hazard. Keep all small components and packaging away from young children.

• This product is not a toy. Do not allow children to play near the stand without direct supervision.

• A minimum of two people is required for installation. Use appropriate safety gear, safe working methods, and proper tools.

• It is highly recommended to use the supplied wall anchoring kit to prevent the stand from toppling, which could result in damage, serious injury, or death.

The weight capacity of the KOGAN KALKTVSTNDA Larvik Studio Stand depends on the type of floor surface:

• Normal Floor (e.g., concrete): The maximum rated load is 32kg (70.4lbs).

• Glossy Floor (e.g., hardwood): The maximum rated load is 25kg (55lbs).

To help prevent the KOGAN KALKTVSTNDA TV stand from tipping over, which can be a serious danger to children, please follow these guidelines:

• NEVER allow children to stand on, climb, or hang on TV stands.

• Ensure the TV is properly anchored to the TV stand before use around children.

• It is highly recommended to use the supplied wall anchoring kit to secure the stand to a wall. Failure to anchor the product may result in damage, serious injury, or death.

The following components are supplied for the assembly of your KOGAN KALKTVSTNDA Larvik Studio Stand:

• A – Front Leg (x2)

• B – Rear Leg (x1)

• C – Bottom TV Bracket (x1)

• D – Top TV Bracket (x1)

• E – Main Pole (x1)

• F – Anti-toppling Strap (x1)

• G – Cable Clip (x2)

• H – Top Plate (x2)

• I – Cable Management Clip (x2)

The KOGAN KALKTVSTNDA comes with the following hardware pack:

• J – Screw (x2)

• K – 2mm Allen Key (x1)

• L – 4mm Allen Key (x1)

• M – Anti-toppling Screw (x4)

• N – Wall Anchor (x4)

• M-A – M5x14 Bolt (x4)

• M-B – M6x16 Bolt (x4)

• M-C – M6x30 Bolt (x4)

• M-D – M8x30 Bolt (x4)

• M-E – M8x50 Bolt (x4)

• M-F – Bracket (x4)

• M-G – Small Spacer (x8)

• M-H – Large Spacer (x8)

Follow these steps to assemble your KOGAN KALKTVSTNDA stand:

Step 1: Assemble the Legs

Attach the two front legs (A) and the rear leg (B) to the main pole (E). Secure them in place.

Step 2: Position the Locking Collar

Slide the locking collar onto the main pole. Position it at a recommended height of 50-150mm from the top of the pole. Secure the locking collar firmly before attaching the TV screen.

Step 3: Prepare the TV Brackets

Attach the mounting plate to the bottom TV bracket (C) and tighten the screw.

Step 4: Attach Brackets to the TV

Place your TV face down on a soft, flat surface. Attach the top (D) and bottom (C) TV brackets to the back of your TV using the appropriate bolts (M-A, M-B, M-C, M-D, M-E) and spacers (M-G, M-H) for your TV’s mounting holes. Ensure the cable clips (G) are attached to the upper bracket.

Step 5: Mount the TV onto the Stand

With the help of another person, carefully lift the TV and hook the top bracket (D) onto the top plate of the main pole. Gently lower the TV until the bottom bracket (C) rests against the pole. Secure the bottom bracket to the pole by turning the locking mechanism.

Step 6: Manage Cables

Remove the adhesive backing from the cable management clips (I). Attach them to the rear leg of the stand. Secure the TV’s power and other cables within the clips using the screws (J).

Step 7: Final Adjustments

Check that the TV is level and secure. The TV can be swiveled up to ±180 degrees. Ensure the screen does not touch the stand’s aluminum plate during rotation.

To safely secure the KOGAN KALKTVSTNDA to the wall, follow these steps:

1. Position the stand in its final location against the wall.

2. Mark two spots on the wall for the anchors, at a height between 1100-1350mm from the floor and spaced 400-650mm apart.

3. Drill holes at the marked spots. The drill bit size should be appropriate for the wall anchors (N).

4. Insert the wall anchors (N) into the drilled holes.

5. Secure one end of the anti-toppling strap (F) to the wall using the anti-toppling screws (M).

6. Attach the other end of the strap (F) to the back of the TV mount or a secure point on the stand.

7. Tighten the strap until it is taut, ensuring there is no slack. Use the 2mm Allen Key (K) if necessary for securing components.

The dimensions and specifications for the KOGAN KALKTVSTNDA Larvik Studio Stand are as follows:

• Total Height: 1385mm

• Footprint Width: 880mm

• Leg Height from Floor: 420mm

• Pole Diameter: 35mm

• Horizontal Distance between Mounting Bars: 600mm

• Mounting Bar Length: 644mm

• VESA Compatibility (Horizontal): Minimum 100mm to maximum 600mm

• VESA Compatibility (Vertical): Minimum 100mm to maximum 400mm

• Swivel Range: ±180°

Yes, for continued safety and stability, you should inspect all joints on the KOGAN KALKTVSTNDA every 3 months. If you find any loose screws, re-tighten them before continuing to use the stand.