KOGAN SMARTERHOME KASPS30WACB (01) PDF Document

The KOGAN SMARTERHOME KASPS30WACB Smart Power Board consists of the following components:

1. Reset Button: Used to reset the device and put it into pairing mode.

2. USB-C Port: For charging compatible devices.

3. Outlet: Three standard electrical outlets.

4. Power Plug: Connects the power board to a wall outlet.

5. Pairing Indicator: Shows the Wi-Fi pairing status.

6. USB-A Port: For charging compatible devices.

7. Operation Indicators: Indicate when the electrical outlets are active.

To operate the KOGAN SMARTERHOME KASPS30WACB, follow these steps:

1. Connect the power plug to an electrical outlet and turn the outlet on.

2. Connect your device to one of the 3 available electrical outlets on the power board.

3. Once successfully connected, the ‘Operation’ indicator will illuminate, confirming the electrical outlet is active.

4. Alternatively, use one of the USB-C ports or the USB-A port to charge your device directly.

Install the App

Download the Kogan SmarterHome™ app from the Apple App Store (iOS) or the Google Play Store (Android).

Log In or Sign Up

1. If you already have a SmarterHome account, tap ‘Log In’. To register a new account, tap ‘Sign Up’.

2. The app will automatically recognise your country. If needed, you can manually select your country from the drop-down menu. Enter your email address, agree to the Privacy Policy and User Agreement, and tap ‘Get Verification Code’ to continue.

3. A 6-digit code will be sent to the submitted email address. Enter the code before the one-minute timer expires.

4. Enter a password that uses 6-20 characters with a mix of letters and numbers and tap ‘Done’.

5. Enable the permissions and tap ‘Go to App’.

When the device is first turned on, it may automatically enter pairing mode (the ‘Pairing’ indicator flashes rapidly).

If not automatically in pairing mode when powered on, you can manually set the device in pairing mode by:

1. Powering the device off for 10 seconds, then powering it on again.

2. Pressing and holding the ‘Reset’ button for 5 seconds until the ‘Pairing’ indicator flashes rapidly.

1. Open the SmarterHome™ app.

2. Tap the ‘+’ icon in the top right corner of the screen and then tap ‘Add Device’.

3. Tap ‘Add’ when the device appears. Alternatively, select the product type from the list of options in the app (Electrical > Power Strips).

4. Follow the prompts to add your device to the app.

Notes:

• The device and the app must use the same Wi-Fi network.

• The device is only compatible with 2.4GHz networks.

If the standard ‘EZ Mode’ connection does not work, you can attempt to connect using AP Mode.

Set the Device in AP Pairing Mode

To set the device in AP pairing mode:

1. Power the device off for 10 seconds, then power on again.

2. Press and hold the ‘Reset’ button for 5 seconds until the ‘Pairing’ indicator flashes rapidly.

3. Press and hold the ‘Reset’ button again for 5 seconds until the ‘Pairing’ indicator flashes slowly.

Add the Device to the App

When the device is in AP pairing mode, follow the previous steps to add the device to the app.

1. Ensure you are logged into the Kogan SmarterHome™ app.

2. Open the Google Home app.

3. Go to the devices tab and tap the ‘+ Add’ button in the lower right corner.

4. Tap ‘Works with Google Home’.

5. Search for ‘Smarter Home’ in the search bar and select ‘Smarter Home’ from the results.

6. Tap the ‘Agree and link’ button.

7. Once linked, a ‘Smarter Home is linked’ pop-up will appear at the bottom of the screen.

8. Tap your device and then tap the ‘Next’ button.

9. Select the home you wish to add the device to and tap the ‘Next’ button.

10. Select the room your device is in and tap the ‘Next’ button.

1. Ensure you are logged into the Kogan SmarterHome™ app.

2. Open the Amazon Alexa app.

3. Go to the ‘More’ tab and tap ‘Skills & Games’.

4. Search for ‘Smarter Home’ in the search bar and select ‘Smarter Home’ from the results.

5. Tap the ‘ENABLE TO USE’ button.

6. Tap the ‘Agree and link’ button.

7. Once linked, tap ‘Next’. Alexa will search for any compatible devices.

8. Once your device has been found, tap ‘Next’.

9. Rename the device to your desired name and tap ‘Update Name’.

10. Select the room your device is in and tap ‘Add To Group’.

11. Once the device has been successfully added to your desired room, tap ‘Continue’.

12. You can now view and manage your device from the ‘Devices’ tab.