KOGAN KATVSFTW43A (01) PDF Document

Before starting installation and assembly of your KOGAN KATVSFTW43A TV stand, please read the entire user guide. Pay close attention to the following safety warnings:

• Use with products heavier than the rated weights indicated may result in instability causing possible injury.

• Please closely follow the assembly instructions. Improper installation may result in damage or serious personal injury.

• Safety gear and proper tools must be used. This product should only be installed by professionals.

• This product is designed to be installed on solid concrete walls, masonry walls or wood stud walls.

• Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.

• Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.

• This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.

• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

• Never exceed the maximum load capacity.

To help prevent the KOGAN KATVSFTW43A TV stand from toppling over, which can cause serious injury or death, please follow these guidelines:

• NEVER allow children to stand, climb or hang on the TV stand.

• Ensure the TV is properly anchored to the TV stand before use around children.

The specifications for the KOGAN KATVSFTW43A TV stand are as follows:

• Suitable TV Size: 17″ – 43″ TVs

• Maximum TV Load Capacity: 15kg (33lbs)

• Shelf Rated Load Capacity: 5kg (11lbs)

• VESA Compatible Patterns: 75×75, 100×100, 100×200, 200×100, 200×200

You should check that the KOGAN KATVSFTW43A TV stand is secure and safe to use at regular intervals, at least every three months.

The following components are included for the assembly of the KOGAN KATVSFTW43A TV stand:

• (A) Base (x1)

• (B) Shelf Upright (x1)

• (C) Upright (x1)

• (D) Shelf (x1)

• (E) TV Holder (x1)

• (F) TV Bracket (x1)

• (G) Pocket (x1)

• (H) Curved Washer (x2)

• (I) M6x12 Screw (x6)

• (J) M6x18 Screw (x4)

• (K) M6x70 Screw (x2)

• (L) D6 Washer (x3)

• (M) Allen Key (4mm) (x1)

• (N) Open Spanner (8-10mm) (x1)

• (M-A) M4x14 Screw (x4)

• (M-B) M5x14 Screw (x4)

• (M-C) M6x14 (x4)

• (M-D) M8x20 (x4)

• (M-E) D5 Washer (x4)

• (M-F) D8 Washer (x4)

• (M-G) Spacer (x8)

Before starting installation, ensure you have received all parts by checking them against this component checklist. If any parts are missing or faulty, contact your place of purchase for a replacement.

Follow these steps to assemble your KOGAN KATVSFTW43A TV stand:

Step 1: Attach the shelf

Attach the shelf (D) to the shelf upright (B) using four M6x12 screws (I). Tighten the fasteners with the Allen key (M).

Step 2: Attach the base

Attach the base (A) to the shelf upright (B) using three M6x18 screws (J) and three D6 washers (L). Tighten the fasteners with the Allen key (M).

Step 3: Attach the main upright

Attach the upright (C) to the shelf upright (B) and secure it in place using two M6x12 screws (I). Tighten the fasteners with the Allen key (M).

Step 4: Attach the TV holder

Attach the TV holder (E) and the two curved washers (H) to the upright (C). Secure them in place using two M6x70 screws (K). Tighten the fasteners with the Allen key (M).

Step 5: Attach the bracket to the TV

Align the TV bracket (F) with your TV’s VESA holes and secure it using the supplied screws (‘M-‘set), washers (M-E, M-F), and spacers (M-G) depending on the required length for your TV model.

Step 6: Mount the TV

Carefully hook the TV bracket onto the TV holder. It is recommended that 2 people carry the TV to prevent damage. Secure the TV in place using an M6x18 screw (J). Tighten the fastener with the Allen key (M).

Step 7: Attach the pocket

Attach the pocket (G) underneath the shelf.

Step 8: Route cables

Route the TV cables through the holes in the upright and shelf upright for cable management.

To adjust the tilt and angle of the TV, use the provided spanner (N) to loosen the fasteners on the TV holder mechanism. Adjust the TV to the desired position and then retighten the fasteners securely.

If the display does not stay at your desired position, loosen the screws on the adjustment mechanism, adjust the display to the desired angle, and then tighten the screws securely.