HUBBLE CONNECTED AI VISION HB570AI (01) PDF DOCUMENT

The contents inside the box are:

• Baby Unit (Camera)

• Wall Wire Cover A (x2)

• Wall Wire Cover B (x7)

• Wall Wire Cover C

• USB Power Cable

• USB Charger

• Camera Hook

• Quick Start Guide

Strangulation hazard. Children have STRANGLED on cords. Keep this cord out of the reach of children (more than 3ft (1m) away). Never use extension cords with AC Adaptor. Only use the AC Adaptor provided.

1. Light sensor

2. Camera Lens

3. Microphone

4. Power LED Indicator

5. Micro-SD card Slot (Not applicable for HB570AI, HB570AI-2)

6. Night Light

7. USB-C Power Socket

8. PAIR Button

9. Speaker

• Steady Red: Offline

• Steady Blue: Connected

• Blink between Red and Blue alternatively: Pairing

1. Insert the USB-A (bigger end) plug of the USB cable into the USB charger then insert the USB-C (smaller end) into the USB-C socket at the bottom at the back of the camera.

2. Connect the USB charger to an electrical outlet.

3. The power indicator on the camera lights in blue colour.

Note: Only use the supplied power adapter (DC5V/1000mA).

A. Install HubbleClub by Hubble Connected App

1. Scan the QR code with your smart device and download HubbleClub by Hubble Connected App from the App Store for iOS devices or from the Google Play™ Store for Android™ devices.

2. Install HubbleClub by Hubble Connected App on your device.

B. View on Compatible Smartphones and Tablets.

1. Open the HubbleClub by Hubble Connected App on your compatible smartphone or tablet.

2. Follow the in-app instructions to create your Hubble account and connect to your device.

Smartphones/Tablets: iOS 12.0, Android™ 8.0

Al Vision Camera features advanced Al prediction algorithms so that unsafe sleep postures like when baby has their face covered face or aren’t on their back, are detected and you are alerted via the HubbleClub app.

For accurate detection and notification of all events, please mount the camera in a bird’s eye view to oversee your baby at about 4 to 5 ft (1.2 to 1.5m) distance for optimal detection.

• Position the camera hook on the wall according to the expected camera height against the crib mattress.

• Mark on the wall the two mounting screw holes of the camera hook disc.

• Drill 2 holes with the size suitable for fitting a #6 (4mm) screw drywall anchor.

• Use the #6 (4mm) self-tapping screws and associated drywall anchors to mount the disc on the wall.

• Snap fit the camera hook to the disc by first aligning the UNLOCK marks of both parts.

• Turn clockwise to lock the hook onto the disc with the LOCK marks aligned.

• Wind the flexible arm of the camera to the camera hook as shown and adjust the camera head so that it is pointing to an overhead bird’s eye view of baby’s sleep position that suitably covers the crib.

• Remove the camera hook from the disc, dress the USB power cable that connected to the power adaptor and the camera unit inside the disc.

• When the camera is securely positioned on the disc, plug the USB-C plug of the USB power cable into the power socket at the rear of the camera unit.

To prevent the power cable from being within reach and being a potential choke hazard for the baby in the crib, it is highly recommended to cover the power cable with the Wall Wire Cover provided – Cover A is for the start and end; Cover B is for the middle sections and Cover C is the right-angled cover for turning the orientation from vertical to horizontal.

• Clean the wall with a soft cloth or an alcohol wipe before using the adhesive.

• Remove the clear film from the double adhesive behind each of the wall wire covers as below shown.

• Start with wall wire cover A below the camera to cover the power cable then press the cover to Stick to the wall.

• Snap fit the wall wire cover B immediate after the cover A. Then press to stick to the wall.

• Repeat snapping the wall wire cover B.

• Repeat the steps until the cable is entirely covered by the wall wire covers as shown.

• Insert the USB-A (bigger end) plug of the USB power cable into the USB charger.

• Connect the USB charger to the electrical outlet.

The flexible arm of the camera allows you to twist it to a circular ring base that can be used for desktop mounting and mounting across a variety of surfaces. Please note to press the base ring flat for optimal stability. Make sure the camera head is positioned as close to the center of the base ring as possible.

The disc of the camera hook base can be separated as a desktop stabilizer. You can wind the camera flexible arm around it and snap part of the arm in the disc notch to hold it firmly.

At the end of the product life cycle, you should not dispose of this product with normal household waste. Take this product to a collection point for the recycling of electrical and electronic equipment. The symbol on the product, user’s guide and/or box indicates this. Some of the product materials can be re-used if you take them to a recycling point. By reusing some parts or raw materials from used products you make an important contribution to the protection of the environment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.