Free English HOMEMATIC HMIP-SWSD-2 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD HOMEMATIC HMIP-SWSD-2 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
What is the function of the Homematic IP Access Point 2 included with the HOMEMATIC HMIP-SWSD-2?
The Homematic IP Access Point 2 is the central element of the Homematic IP smart home system and communicates with the Homematic IP radio protocol.
All devices of the system can be configured and controlled comfortably and individually with a smartphone via the Homematic IP app. The scope of functions varies depending on the number of components in your system.
How does the HOMEMATIC HMIP-SWSD-2 Smoke Alarm function?
The HOMEMATIC HMIP-SWSD-2 Smoke Alarm monitors a room for smoke emissions. The device works on the basis of the photoelectric scattered light principle. This enables fire and dangerous smoke gases to be detected at an early stage and a warning to be given in good time. When an alarm has been triggered, the integrated siren sounds and the warning LED will start to flash red. A white LED acts as emergency lighting for easy orientation also in the event of a power failure.
What do the safety and information symbols in the manual for the HOMEMATIC HMIP-SWSD-2 indicate?
The symbols in the manual indicate the following:
Attention! This indicates a hazard.
Additional important information.
What is the Declaration of Conformity for the HOMEMATIC HMIP-SWSD-2?
The manufacturer declares that the radio equipment type Homematic IP HmIP-SK27 is compliant with Directive 2014/53/EU. The full text of the EU declaration of conformity is available.
What are the technical specifications for the HOMEMATIC HMIP-SWSD-2 and the accompanying Homematic IP Access Point 2 (HmIP-HAP2)?
| Specification | HOMEMATIC HMIP-SWSD-2 | HmIP-HAP2 |
|---|---|---|
| Device short name | HmIP-SWSD-2 | HmIP-HAP2 |
| Supply voltage | 2x permanently installed 3 V lithium batteries | 5 VDC // 5 VCC |
| Plug-in mains adapter (input) | – | 100 V-240 V/50 Hz |
| Power consumption plug-in mains adapter max. | – | 2.5 W |
| Standby power consumption | – | < 1 W |
| Current consumption | – | max. 500 mA |
| Battery life in years (type) | 10 years (typically) | – |
| Degree of protection | – | IP20 |
| Degree of pollution | 2 | – |
| Ambient temperature | -5 to 30 °C | 5 to 35 °C |
| Dimensions (W x H x D) | 115 x 45 mm | 104 x 104 x 40 mm |
| Weight | 148 g | 165 g |
| Radio frequency | 868.0-868.6 MHz/869.4-869.65 MHz | |
| Receiver category | SRD category 2 | |
| Maximum radiated power | 10 dBm | |
| Typical open area RF range | 200 m | 300 m |
| Duty cycle | < 1% per h /< 10% per h | |
| Alarm type | scattered-light smoke | – |
| Alarm output | piezo signal transmitter (>85 dB over 3 m distance), status LED, wireless | – |
| Display | Status LED, emergency | – |
| Type of installation | Ceiling mounting | – |
| Network | – | 10/100 MBit/s | Auto-MDIX |
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
CLICK HERE TO DOWNLOAD HOMEMATIC HMIP-SWSD-2 (01) PDF DOCUMENT