HISENSE PARTY ROCKER ONE PLUS (01) PDF Document

The HISENSE PARTY ROCKER ONE PLUS features:

• Bluetooth playback

• AUX IN

• FM tuner

• USB slot

• Microphone function

• Guitar function

• Multiple EQ sound effect mode

The package for the HISENSE PARTY ROCKER ONE PLUS contains:

• Main Unit

• User Manual, Quick Start Guide, Warranty Card

• AC power cord (quantity and plug type vary by region)

• 2 x Wireless Microphones

• 4 x AA batteries (1.5V)

To connect the speaker to power, ensure that the power supply voltage corresponds to the voltage printed on the back or the underside of the unit. Then, insert the AC power cord into the AC INPUT SOCKET on the rear of the speaker and plug the other end into a mains socket.

The HISENSE PARTY ROCKER ONE PLUS has an audio input terminal to connect external devices like VCD, CD, VCR, or MP3 players.

1. Use an audio cable with a 3.5mm connector (not supplied) to connect the external device to the AUX IN socket on the rear panel of the unit.

2. Press the SOURCE button on the top panel to select AUX IN mode.

3. You can now play audio from your connected device through the speaker.

You can output audio from the HISENSE PARTY ROCKER ONE PLUS to another external device, such as an active speaker.

1. Connect an audio cable (not supplied) from the AUX OUT jack on the rear panel of your speaker to the AUX IN jack of the external device.

2. The audio will be output automatically to the external device.

1. Insert a wired microphone (not included) into the MIC socket on the rear panel.

2. Adjust the MIC VOLUME ADJUST knob to a low level.

3. Adjust the microphone volume level to your desired level using the same knob.

To connect a guitar, insert the guitar cable into the GUITAR socket on the rear panel. You can then adjust the guitar volume using the GUITAR VOLUME ADJUST knob.

By default, the supplied wireless microphones come pre-paired with the speaker from the factory.

1. Load the two Alkaline AA batteries into each microphone, ensuring correct polarity.

2. Turn on the speaker using the POWER ON/OFF button on the top panel.

3. Press the power button on a wireless microphone to switch it on. The indicator on the microphone will blink blue and automatically pair with the speaker.

4. Once paired successfully, the indicator on the microphone will stay solid blue.

5. Adjust the microphone volume to your desired level using the MIC VOLUME ADJUST knob on the rear panel of the speaker.

Note: The microphone powers off automatically after 20 minutes of inactivity. A maximum of two wireless microphones are supported.

When the battery of the wireless microphone is low, the indicator on the microphone will blink red. This indicates that you need to replace the old batteries in the microphone’s battery compartment with new ones.

Standby/ON:

• Press the POWER ON/OFF button on the unit to switch the main unit ON.

• Press and hold the same button for 2 seconds to turn it OFF.

• The unit will automatically switch to Standby mode if there is no input signal for more than 15 minutes.

Select Modes:

• Press the SOURCE button to cycle through the play functions: BT → USB → AUX IN → FM mode.

Adjust the Volume:

• Press the MASTER VOLUME +/- buttons to adjust the volume.

DJ Effect:

• Press the DJ button to select different DJ effects.

• Continuously press the DJ button within 1 second to cycle through the effects: DJ1 cheering sound, DJ2 drum sound, DJ3 alarm sound, DJ4 horn sound, DJ5 disc playing sound.

Preset Equalizer:

• During play, press the EQ button repeatedly to select from ROCK, JAZZ, SAMBA, POP, or BALANCE.

Bass Settings:

• Press the BASS button to select BASS ON or BASS OFF.

• Press the LIGHT button repeatedly to select the LED effect: LED OFF, LED1, LED2, LED3, LED4, LED5.

• Press and hold the LIGHT button to switch the strobe light ON/OFF.

The HISENSE PARTY ROCKER ONE PLUS can charge wireless charging compatible phones. Simply place your phone on top of the wireless charging logo on the top panel of the speaker.

Note:

1. Wireless charging can be used when the unit is in power-on state or in standby for up to 4 hours while connected to AC power.

2. To prolong the service life of the battery, direct wireless charging is not allowed when the speaker is running on battery power.

1. Press the SOURCE button on the unit to select Bluetooth mode. The display screen will show “PAIRING”.

2. Activate the Bluetooth function on your device and select the search mode.

3. “Hisense Party Rocker One Plus” will appear in your Bluetooth device list.

4. Select “Hisense Party Rocker One Plus” from the pairing list. The word “CONNECTED” will scroll on the display screen when the connection is successful.

5. Begin playing music from your connected Bluetooth device.

Tips:

• The operational range is approximately 8 meters.

• If a password is required, enter “0000”.

To disconnect the Bluetooth function, you can:

• Switch to another function on the unit (e.g., AUX, FM).

• Disable the Bluetooth function on your device.

• Press and hold the PLAY/PAUSE/PAIR button on the unit.

This TWS connection only works between two identical speakers.

1. Power on both speakers.

2. Press the SOURCE button on both speakers to switch them to Bluetooth mode.

3. On one of the speakers, press the TWS button on the rear panel. The display will show “TWS ON,” then “TWS PAIRING.” The two speakers will enter the pairing state automatically.

4. Once paired successfully, one speaker will display “MASTER” (this will be the master speaker and left channel) and the other will display “SLAVE” (this will be the slave speaker and right channel).

5. Enable Bluetooth on your device and connect to “Hisense Party Rocker One Plus” from the list of discovered devices.

6. To disconnect TWS mode, press and hold the TWS button. The display will show “TWS OFF.”

1. Insert the USB device into the USB SLOT on the rear panel.

2. Press the SOURCE button on the top panel to select USB mode.

3. Play should start automatically. If not, press the PLAY/PAUSE button.

• To skip to the previous/next track, press the PREVIOUS/NEXT buttons.

• To skip to the previous/next folder, press and hold the PREVIOUS/NEXT buttons.

• In PLAY/PAUSE state, press and hold the PLAY/PAUSE button for 3 seconds to switch among REPEAT 1, REPEAT ALL, RANDOM, and NORMAL modes.

The USB port (Charging 5V 1A) is designed for charging mobile devices. While the speaker is in power-on mode, use a USB cable (not included) to connect your mobile device to the USB SLOT. The mobile device will start charging. It supplies 5V DC at a charging current up to 1000mA (1A).

First, press the SOURCE button repeatedly to select the TUNER source. The display will show “TUNER”.

Auto Tuning:

1. Press and hold the PLAY/PAUSE button to start auto tuning. The searched radio stations will be stored as preset stations.

2. Press the PLAY/PAUSE button again to stop the auto tuning.

Manual Tuning:

• Press the NEXT or PREVIOUS buttons until the optimal reception frequency is reached. Each press increases or decreases the frequency by 0.05MHz.

Recalling a Preset Station:

1. Press the PLAY/PAUSE button to switch between preset station and frequency.

2. Press the NEXT or PREVIOUS buttons to select your desired preset station.

Use the included AC power cord to connect the AC power input socket on the unit to an AC power outlet. The charging-indicator lights on the top panel will flash during charging. When all five charging-indicator lights stay solid, the battery is fully charged.

Alternatively, you can use a vehicle DC power adapter (not included) connected to the DC IN socket on the unit.

Note: When the battery is low, the unit will emit a prompt beep. When the DC in is connected for charging, the unit can only be charged and cannot be played.

The battery level is indicated by the white LED lights on the top panel:

• 5 LED white lights up: approx. 100% full

• 4 LED white lights up: approx. 80% full

• 3 LED white lights up: approx. 60% full

• 2 LED white lights up: approx. 40% full

• 1 LED white light up: approx. 20% full (indicating charging is needed)

If there is no power, please check the following:

• Ensure that the AC cord is properly connected to both the speaker and the AC outlet.

• Ensure that there is power at the AC outlet.

• Press the POWER ON/OFF button on the speaker.

If you hear buzzing or humming, try these steps:

• Ensure all cables and wires are securely connected.

• Connect a different source device (e.g., Blu-ray player) to see if the buzzing persists. If it does not, the problem may be with the original device.

• Connect your device to a different input on the speaker.

If you are unable to find the Bluetooth name “Hisense Party Rocker One Plus” on your device, please try the following:

• Ensure the Bluetooth function is activated on your Bluetooth device.

• Re-pair the unit with your Bluetooth device. Make sure the speaker is in “PAIRING” mode.

*15 hrs battery playtime is only for reference and may vary depending on music content and battery aging after numerous charging and discharging cycles. It’s achievable with a predefined music source, light show switched off, volume level at 7, and BT streaming source.