HISENSE PARTY ROCKER ONE (01) PDF Document

The HISENSE PARTY ROCKER ONE features:

• Bluetooth playback

• AUX IN

• FM tuner

• USB slot

• Microphone function

• Guitar function

• Multiple EQ sound effect mode

The package for the HISENSE PARTY ROCKER ONE includes:

• Main Unit

• AC power cord (quantity and plug type vary by region)

• User Manual

• Quick Start Guide

• Warranty Card

The Party Rocker One Plus model also includes:

• Wireless Microphone x2

• AA battery (1.5V) x 4

To connect the HISENSE PARTY ROCKER ONE to power, ensure that the power supply voltage corresponds to the voltage printed on the back or underside of the unit. Insert the AC power cord into the AC INPUT SOCKET on the rear of the speaker and then into a mains socket.

The HISENSE PARTY ROCKER ONE has an audio input terminal to connect analog stereo audio signals from external devices like VCD, CD, VCR, or MP3 players. Use an audio cable with a 3.5mm connector (not supplied) to connect the external device to the AUX IN terminal on the rear panel of the speaker. Press the SOURCE button on the top panel to select AUX IN mode.

The HISENSE PARTY ROCKER ONE has an AUX OUT jack that allows you to output analog stereo audio signals to external devices, such as an active speaker. Connect an audio cable (not supplied) from the AUX OUT jack on the rear panel of the unit to the AUX IN jack of the external device. The unit will automatically output audio to the external device.

To connect a wired microphone for karaoke:

1. Insert the microphone into the MIC socket on the rear panel.

2. Adjust the microphone volume to a low level using the MIC VOLUME ADJUST knob on the rear panel.

3. Adjust the microphone volume level to your desired level using the same knob.

To connect a guitar, insert the guitar cable into the GUITAR socket on the rear panel of the HISENSE PARTY ROCKER ONE. You can then adjust the guitar volume using the GUITAR VOLUME ADJUST knob.

The wireless microphone comes pre-paired with the speaker from the factory. To connect it:

1. Load the two supplied Alkaline AA batteries into the microphone, observing the correct polarity.

2. Turn on the speaker using the power button on the top panel.

3. Press the power button on the wireless microphone to switch it on. The indicator on the microphone will blink blue.

4. The wireless connection will be set up automatically. Once paired successfully, the indicator on the microphone will keep a solid blue light.

5. Adjust the microphone volume to your desired level using the microphone volume knob on the rear panel.

Note: The microphone powers off automatically after 20 minutes of inactivity. A maximum of two wireless microphones are supported.

• Blinking Blue: The microphone is in pairing mode.

• Solid Blue: The microphone is successfully connected to the speaker.

• Blinking Red: The microphone battery level is low and the batteries need to be replaced.

• To turn ON: Press the POWER ON/OFF button on the top panel.

• To turn OFF: Press and hold the POWER ON/OFF button for 2 seconds.

• To switch off completely: Disconnect the main plug from the main socket.

The unit will also automatically switch to Standby mode if there is no input signal for more than 15 minutes.

Press the DJ button to select different DJ effects. When you press the DJ button continuously within 1 second, it will cycle to select different DJ sound effects. The DJ sound effect types are:

• DJ1 cheering sound

• DJ2 drum sound

• DJ3 alarm sound

• DJ4 horn sound

• DJ5 disc playing sound

Press the SOURCE button on the unit to select the play function. The modes will cycle in the following order: BT (Bluetooth) → USB → AUX IN → FM mode.

During playback, press the EQ button on the top panel repeatedly to select from the following preset equalizer settings: ROCK, JAZZ, SAMBA, POP, or BALANCE.

Press the BASS button on the top panel to switch between BASS ON and BASS OFF.

• Press the LIGHT button repeatedly to select the LED effect: LED OFF, LED1, LED2, LED3, LED4, LED5.

• Press and hold the LIGHT button to switch the strobe light ON or OFF.

The HISENSE PARTY ROCKER ONE can charge wireless charging compatible phones. Simply place your phone on top of the wireless charging logo on the party speaker.

Note:

1. Wireless charging can be used when the unit is in power on state or standby after 4 hours for AC mode.

2. To prolong the service life of the battery, direct wireless charging is not allowed when the speaker is running on battery power.

1. Press the SOURCE button on the unit to select Bluetooth mode. The word “PAIRING” will be shown on the display screen.

2. Activate your Bluetooth device and select the search mode.

3. “Hisense Party Rocker One” or “Hisense Party Rocker One Plus” will appear on your Bluetooth device list.

4. Select it from the pairing list. The word “CONNECTED” will scroll on the display screen when successful.

5. Begin playing music from the connected Bluetooth device.

Tip: Enter “0000” for the password if necessary. The operational range is approximately 8 meters.

TWS connection is used between two identical HISENSE PARTY ROCKER ONE speakers for stereo sound.

1. Power on both speakers and press the SOURCE button on both to switch to Bluetooth mode.

2. Press the TWS button on one of the speakers. The display will show TWS ON, and then TWS PAIRING. The speakers will enter the pairing state automatically.

3. Once paired successfully, one speaker will display MASTER (this is the left channel and receives the Bluetooth signal) and the other will display SLAVE (this is the right channel).

4. Enable your Bluetooth device, search for and connect to “Hisense Party Rocker One” or “Hisense Party Rocker One Plus”.

To disconnect TWS mode, press and hold the TWS button. The display will show TWS OFF.

1. Insert a USB device into the USB SLOT on the rear panel.

2. Press the SOURCE button to select USB mode.

3. Playback will start automatically. If not, press the PLAY/PAUSE button.

• To skip to the previous/next track, press the PREVIOUS/NEXT buttons.

• To skip to the previous/next folder, press and hold the PREVIOUS/NEXT buttons.

• In PLAY/PAUSE state, press and hold the PLAY/PAUSE button for 3 seconds to switch among REPEAT 1, REPEAT ALL, RANDOM, and NORMAL modes.

Yes, the USB Charging socket (5V, 1A) is designed for charging mobile devices like MP3 players and mobile phones. In power on mode, use a USB cable (not included) to connect your mobile device to the USB Charging socket, and the device will begin to charge.

Press the SOURCE button repeatedly to select the TUNER source. The display will show “TUNER”.

Auto Tuning:

Press and hold the PLAY/PAUSE button to start auto-tuning. Searched radio stations will be stored as preset stations. Press the PLAY/PAUSE button again to stop the auto-tuning.

Manual Tuning:

• Press and hold the PREVIOUS or NEXT button to start forward or reverse scanning. The scanning will stop automatically when a station is found.

• For fine-tuning, briefly press the PREVIOUS or NEXT buttons to change the frequency by 0.05MHz.

Recalling a Preset Station:

Press the PREVIOUS or NEXT button to switch between preset stations and their frequencies.

Use the included AC power cord to connect the AC power input socket on the unit to an AC power outlet. The charging-indicator lights on the top panel will flash during charging. When all five charging-indicator lights remain solid, the battery is fully charged.

Alternatively, you can use a vehicle DC power adapter (not included) connected to the DC input socket to charge the unit from a vehicle’s power socket. When the DC in is connected for charging, the unit can only be charged and cannot be played.

The five white LED lights on the top panel indicate the approximate battery charge level:

• 5 LED white lights up: approx. 100% full

• 4 LED white lights up: approx. 80% full

• 3 LED white lights up: approx. 60% full

• 2 LED white lights up: approx. 40% full

• 1 LED white light up: approx. 20% full (indicating charging is needed)

When the battery is low, the unit will emit a prompt beep.

If your speaker won’t turn on, please check the following:

• Ensure that the AC cord is properly connected to the speaker and the AC outlet.

• Ensure that there is power at the AC outlet.

• Press the POWER ON/OFF button on the speaker.

If you hear buzzing or humming, try these steps:

• Ensure all cables and wires are securely connected.

• Connect a different source device (e.g., Blu-ray player) to see if the buzzing persists. If it does not, the problem may be with the original device.

• Connect your device to a different input on the speaker.

If you cannot find the speaker’s Bluetooth name on your device:

• Ensure the Bluetooth function is activated on your Bluetooth device.

• Re-pair the unit with your Bluetooth device by following the pairing instructions again.

*15 hrs battery playtime is only for reference and may vary depending on music content and battery aging after numerous charging and discharging cycles. It’s achievable with a predefined music source, light show switch off, volume level at 7 and BT streaming source.