GREAT AMERICAN POPCORN UE40043 (01) PDF Document

Before using your GREAT AMERICAN POPCORN UE40043, you must read all instructions. Please adhere to the following safety guidelines:

• Do not touch hot surfaces. Always use handles or knobs to operate.

• To avoid any risk of electrical shock, do not immerse cord or plug into water or other liquid.

• Close supervision is necessary when it is being used near children.

• Unplug main power cord from outlet while not in use and before cleaning.

• Allow hot parts to cool down before moving.

• Do not operate the appliance with a damaged cord or plug, malfunction, or with any mechanical damages. Send the unit to the nearest authorized service center for examination and repair. (ONLY technicians should open up the unit).

• It may cause injury by using any accessories or attachments not provided or recommended by the manufacturer.

• Do not pop the kernels in a dry pot (without oil).

• Do not immerse popping pot into water.

• Pot surface is HOT and should NOT be touched during popping or just after use.

• Unplug, clean and cover the unit and store in a dry and safe place if not being used for long periods of time.

• Do not leave the power cord hanging over the edge of a table or counter.

• DO NOT place the unit on or near a hot gas or electric burner or in a heated oven.

• Extreme caution must be paid when moving the appliance containing hot oil or other hot liquids.

• Turn ALL switches to the “OFF” position before disconnecting the power plug from the wall supply outlet.

• Not recommended for outdoor use.

• Do not use the appliance for anything other than the indicated usage.

• To avoid overheating, always have oil and kernels ready before operating.

• Extreme caution must be used when unloading the heat pot; always use an oven mitt.

• Always place the unit over a counter-top so that residual hot oil or water running out will not cause injury.

• KEEP OUT OF REACH OF CHILDREN.

• Do not clean using any abrasive material.

• Never force any parts or brackets into position.

• No parts are intended for the dishwasher.

• Save these instructions for future reference.

For first-time use, clean the inside glass and wipe the inside area with a damp sponge. Thoroughly wipe the inside of the stainless steel pot with a clean damp sponge before heat is applied.

1. Use the bolts & washers provided to connect the Long stand (K) and the 2 pcs square pole (L) together.

2. Connect the completed assembly from step 1 with the short stand (J) using the bolts & washers provided.

3. Insert the axle (M) into the short stand (J). Place wheels (N) on each end of the axle (M). Next, place the provided washers onto each side of the wheels (N) and then attach the round cap nuts using the wrenches provided.

4. Turn the storage cabinet (I) upside down for convenient assembling. Insert both ends of the short and long stand onto the bottom of the cabinet and attach with the bolts provided.

5. Turn the completed unit back to the up-right position. Install the handrail (E) onto the side with the included nuts, bolts, and washers.

6. Place the main unit (A) onto the topside of the storage cabinet.

7. Place the pot (B) onto the hanger. (Note: The roller bar should be on the door side, and also check if the gears between the pot and ceiling are perfectly matched).

8. Connect the power plug from the main unit ceiling with the socket on the bottom of the pot.

9. Open the door of the storage cabinet and release the two spring shafts beneath the main unit in order to fix the main unit with the storage base.

A. Screw the stirrer and spacer onto the gear box.

B. Hold the kettle on the support brace and insert the pin. Lock it into place with the pin provided.

1. Place the corn popper on a dry, level surface. Protect it from rain and other weather elements. Do not install near a pool or water outlets. Plug the unit into a suitable grounded electrical outlet. (Please check if the outlet voltage matches the rating label specified next to the power cord).

2. The main unit has 2 function switches: (I) Spot light & warmer and (II) Stirrer Pot Heater.

3. Hook the stainless steel pot onto the hanger of the main unit. (Note: The roller bar should be on the door side and also check if the gears between the pot and ceiling are perfectly matched).

4. Plug in the power cord (hanging from the main unit ceiling) into the bottom of the stainless steel pot.

5. Switch the light and heater to ON (I & II). The popping pot should be pre-heated for 3 to 5 minutes. If using a Gourmet Tri-Pak, cut off the top of the oil section on the pouch and squeeze the oil into the pot. Allow a few minutes to melt the oil. If using other suitable ingredients, have pre-measured portions ready in advance. Add oil. (Max. 15g/.48 oz. oil).

6. Next, pour popcorn and seasoning from the Gourmet Tri-Pak pouch into the pre-heated oil. If using other suitable ingredients, have pre-measured portions ready in advance. (4 oz. max. uncooked popcorn kernels). Add popcorn. Caution: The lid is hot; it is recommended to wear an oven mitten to contact metal pieces. Close the lid.

7. Switch the Stirrer to ON (II) so that it starts stirring.

8. Close the doors on the main unit carefully.

9. Popcorn starts popping out through the lid after about 2 to 3 minutes.

10. When popping stops (no more popping sound from the pot), switch the stirrer and heater to OFF (II). Popping is completed. Rotate the roller bar on the pot and pour out all remaining popcorn. Gently shake if necessary.

11. The Heater stirrer switch (II) must remain OFF if the unit is not popping. Only the spot light warmer should be left ON; this will keep the popcorn warm, dry, and tasty for a longer period of time.

12. Serve popcorn with the scoop provided. Note: Do not add butter or other liquid flavoring in the main unit popcorn bin. Avoid a big mess! Remove popcorn to a suitable serving bowl or popcorn bag before adding this type of flavoring.

13. Always remove the plug from the power supply before cleaning and if the unit is not being used for a period of time.

• To maintain quality taste and popping conditions, it is recommended that you thoroughly clean the heat pot after using it 3 to 4 times or before prolonged periods of storage.

• Switch OFF both switches. Pour 6 to 10 oz. of water (NO detergent is necessary) into the inner pot.

• Switch ON the stirrer (II) and heater to boil the water and allow the stirrer to rotate, which will help remove debris on the kettle surface. Pour out the water after about 1 to 2 minutes of boiling. Caution: The kettle is hot! Handle with oven mitts. Keep children at a safe distance from the popper during this procedure.

• Repeat the same procedure 2 to 3 times to get a better result.

• Switch off the machine and wait for the popping pot to cool. Clean the inside and outside of the pot with a brush and wet towel. Caution: DO NOT immerse the heat pot in water.

• After using the popcorn machine, use a wet towel to clean up the main unit, main body, and glasses. It is strongly recommended to tidy up the rubbish tray frequently so that there is no food spoilage left behind.

Caution:

• After a popping cycle is complete, the popping pot will be very hot. Use extreme care when handling.

• Remember to turn the heat switch to the off position after the finish of the pop cycle.

• Unplug the unit BEFORE removing the heat pot from the hanger. Use caution not to bump the heat lamp bulb during pot removal.