GLOBE GCB15G-SR (01) PDF Document

Always keep your hands, hair, and clothing away from the heating source of the GLOBE GCB15G-SR.

No. Do not use abrasive cleaners on the GLOBE GCB15G-SR as this might damage the cabinet finish.

Use a clean cloth and a non-abrasive cleaner to clean the stainless steel body of the GLOBE GCB15G-SR. Wipe the polished areas with a soft cloth.

If the stainless steel surfaces of the GLOBE GCB15G-SR become discolored, scrub by rubbing only in the direction of the finished grain.

No. Do not hose down, immerse, or pressure wash any part of the GLOBE GCB15G-SR, excluding the catch tray.

NEVER use a scrubber pad, steel wool, abrasive material, or cleaners containing chlorine, iodine, ammonia, or bromine chemicals, as these will deteriorate the stainless steel and shorten the life of the GLOBE GCB15G-SR.

If cleaning the burner of the GLOBE GCB15G-SR, the main gas valve must be switched to the closed position.

After cleaning the burner of the GLOBE GCB15G-SR, the gas line can be switched back to the open position, then you must follow the lighting instructions in the manual to relight the pilot lights.

Wait at least one hour for the GLOBE GCB15G-SR and its grates to cool after the unit has been turned off.

The unit should be turned off when not in use. It is recommended that the GLOBE GCB15G-SR be disconnected from the gas supply by closing the main gas valve. Use a clean cloth to wipe down controls and knobs.

Place grates on the GLOBE GCB15G-SR with grid bars horizontal, facing down. Turn the broiler on for approximately 45 minutes. Turn off the broiler and allow it to cool for 20 minutes. Clean top and bottom surfaces of the grate with a wire brush to remove animal fats and carbonized grease. Clean channels on grates with a scraper. Remove grates from the broiler and clean the top surface of radiants with the wire brush.

When handling grates, grids, or radiants on the GLOBE GCB15G-SR, always use insulated gloves to prevent burns.

Do not cover the top of the grates grid during a burn off operation on the GLOBE GCB15G-SR. Restricting the airflow may cause them to warp and will also cause damage to the valves, the knobs, and the front panel decal.

Once the GLOBE GCB15G-SR has cooled, remove the cast iron grates. Lift and rock the back support brace toward you; lift the char grate back support brace up and around the back support pins. Clean and de-grease or remove debris from the char grate back support brace. Once clean, reinstall it by angling the long lead edge of the grate back support brace down around the support pins and rock the back support brace around the pins until it is seated flat on the back ledge.

Once the GLOBE GCB15G-SR has cooled, remove the catch tray and discard the waste, grease, debris, and crumbs. The tray is removed by pulling forward. Use caution when removing.

Main burner ports on the GLOBE GCB15G-SR must be kept clean. Close the gas valve to the unit, shutting off the gas and extinguishing the pilot light. Clean in place with a wire brush, or clean gas ports with a sharp-pointed metal instrument to ensure open ports; or the burners may be removed and washed in soapy water for 15 to 20 minutes.

The regulator on the GLOBE GCB15G-SR should be checked monthly to make sure the vent is open and not blocked in any way.

Step 1. Make sure all knobs on the GLOBE GCB15G-SR are in the OFF position.

Step 2. The main gas valve should be CLOSED/OFF for five minutes prior to lighting pilots to clear any existing gas.

Step 3. Turn the main gas valve to ON/OPEN.

Step 4. Light and hold an ignition source at the pilot. When the flame is established, remove the ignition source. Repeat this step for each burner.

Step 5. Turn each burner knob ON. If the burners do not ignite promptly, turn the knobs OFF. From the opening in the front panel, use a screwdriver and turn the pilot valve screw counterclockwise to increase the flame height, and then repeat step 4.

The holes located in the front panel of the GLOBE GCB15G-SR are for pilot valve adjustments. Use a screwdriver to turn the valve to adjust the flame height to your desired level. The pilot flame should be as small as possible, but large enough to guarantee reliable ignition.

To ignite the burner on the GLOBE GCB15G-SR, turn the knob to the ON position, then back off to the desired flame level.

Do not permit fans to blow directly at the GLOBE GCB15G-SR. Avoid open windows next to the unit’s sides or back. Avoid wall type fans which create air cross-currents within a room. Do not block the space between the legs at the bottom, as this admits combustion air.

Turn the burners on about 15 to 20 minutes before cooking for preheating the GLOBE GCB15G-SR.

When the GLOBE GCB15G-SR is first heated, it will smoke until oil used in manufacturing and dust are burned off. An hour at maximum for all burners is usually sufficient.

Place the top cooking grates on the GLOBE GCB15G-SR with the grid bars angled toward the front, or place the grid bars flat, not angled, for cooking. When placed angled toward the front, the grooves on top will guide the excess fat drippings into the grease trough.

If the GLOBE GCB15G-SR is not lighting, check if the main gas line is closed and open the valve. Ensure the pilot light is lit, or ignite it. If the cause is unknown, call for service.

If the flame on the GLOBE GCB15G-SR is too high or too low, adjust the flame with the control knob.

If the pilot light on the GLOBE GCB15G-SR does not stay lit, adjust the pilot light flame height. If the pilot tube is clogged, replace the pilot tube by calling for service.

If there is a strong smell of gas, turn off the main gas valve to the GLOBE GCB15G-SR. Do not light a flame, ignite anything, or turn or switch on anything electrical. Call the fire department if needed and call for service.

If the cooking surface of the GLOBE GCB15G-SR is heating up slowly, it may be due to carbon build up. Ensure that the burners are kept clean and free from carbon build up and debris.

No. If the gas type of the GLOBE GCB15G-SR needs to be converted, contact an authorized servicer or the manufacturer. Do not attempt conversion on your own.