GLOBE GCB36G-SR (01) PDF Document

The GLOBE GCB36G-SR must be operated on a solid, level, nonskid surface that is nonflammable and away from sinks and water hazards.

No, the GLOBE GCB36G-SR is suitable for installation on non-combustible surfaces only.

The non-combustible clearances for the GLOBE GCB36G-SR are 6 inches on the sides, 6 inches in the rear, and 4 inches from the floor.

Screw the legs into the permanently fastened nuts on the four corners of the GLOBE GCB36G-SR and tighten them by hand. Do not slide the unit with the legs mounted; lift it if necessary to move the unit.

Level the GLOBE GCB36G-SR by adjusting the four feet and tightening them securely. The feet have an adjustment of one inch.

The GLOBE GCB36G-SR is factory supplied for use with Natural Gas, with the pressure regulator set at 6 inches W.C.

Check all gas piping on the GLOBE GCB36G-SR for leaks using a soap and water solution before operating the unit. Never use an open flame to check for leaks.

If you smell gas near the GLOBE GCB36G-SR, immediately shut off the main gas valve, extinguish all heat and flames, and call emergency services.

No, you should never leave the GLOBE GCB36G-SR on overnight.

No, you should never use the GLOBE GCB36G-SR as a heating source.

Always turn off the GLOBE GCB36G-SR and allow it to cool down before dismantling for cleaning. Also, ensure the main gas valve is closed if you are cleaning the burner area.

Before operating the GLOBE GCB36G-SR, wash the exterior with a mild detergent or soap solution. When first heated, the unit will smoke until manufacturing oil and storage dust are burned off. Running it at maximum heat for one hour is usually sufficient.

Step 1. Make sure all knobs on the GLOBE GCB36G-SR are in the OFF position.

Step 2. Ensure the main gas valve is closed for five minutes to clear existing gas.

Step 3. Turn the main gas valve to the ON/OPEN position.

Step 4. Light and hold an ignition source at the pilot. Once the flame is established, remove the source.

Step 5. Repeat for each burner’s individual pilot.

To ignite the burner on the GLOBE GCB36G-SR, turn the knob to the ON position, then back off to the desired flame level.

If the burners on the GLOBE GCB36G-SR do not ignite promptly, turn the knobs OFF. From the opening in the front panel, use a screwdriver to turn the pilot valve screw counterclockwise to increase the flame height.

Yes, do not block the space between the legs of the GLOBE GCB36G-SR as it admits combustion air. Additionally, ensure sufficient air enters the room to compensate for ventilation.

Place the angled radiants of the GLOBE GCB36G-SR into the slots on the front and rear supports. Ensure they are centered over the straight sections of the burners.

Place the top cooking grates of the GLOBE GCB36G-SR with the grid bars angled toward the front to guide excess fat into the grease trough, or place them flat.

Use a clean cloth and a non-abrasive cleaner to clean the stainless steel body of the GLOBE GCB36G-SR. Wipe polished areas with a soft cloth.

Place the grates on the GLOBE GCB36G-SR with bars horizontal and facing down. Turn the broiler on for 45 minutes, then off for 20 minutes to cool. Clean top and bottom surfaces with a wire brush to remove grease. Use a scraper on grate channels. Remove grates to clean the top surface of radiants with a wire brush.

After the GLOBE GCB36G-SR has cooled, remove the cast iron grates. Lift and rock the back support brace toward you, then lift it up and around the back support pins. Clean and de-grease the brace. Reinstall by angling the long lead edge down around the support pins and rocking it into place until seated flat on the back ledge.

Once the GLOBE GCB36G-SR has cooled, remove the catch tray by pulling it forward. Discard the waste, grease, and crumbs.

Close the gas valve to the GLOBE GCB36G-SR and extinguish the pilot light. Clean the burner ports in place with a wire brush, or clean gas ports with a sharp-pointed metal instrument. Alternatively, remove the burners and wash them in soapy water for 15 to 20 minutes.

Ensure the main gas line is open. If the pilot light is not lit, attempt to ignite it. If the issue persists, contact a service professional.

The adjustment knob has been turned up or down. Adjust the flame with the control knob.

The flame may be too low, requiring you to adjust the pilot light flame height, or the pilot tube may be clogged, which requires replacement.

Turn off the main gas valve. Do not light any flame, ignite anything, or turn on or switch any electrical device. Call emergency services if needed and call for service.

Carbon build up causes the GLOBE GCB36G-SR to heat up slowly. Ensure that the burners are kept clean and free from carbon build up and debris.

Do not use abrasive or flammable cleaning fluids. Never use a scrubber pad, steel wool, or abrasive material. Avoid cleaners containing chlorine, iodine, ammonia, or bromine chemicals as these will deteriorate the stainless steel of the GLOBE GCB36G-SR.

The body of the GLOBE GCB36G-SR should be cleaned daily using a clean cloth and a non-abrasive cleaner.

The regulator on the GLOBE GCB36G-SR should be checked monthly to ensure the vent is open and not blocked.

Yes, the catch tray of the GLOBE GCB36G-SR should be cleaned per use or at least daily.

Yes, do not cover the top of the grates on the GLOBE GCB36G-SR during a burn off operation. Restricting the airflow may cause them to warp and will cause damage to the valves, the knobs, and the front panel decal.

No, the cooking grates of the GLOBE GCB36G-SR are heavy duty cast iron and will oxidize if emerged in water. Lightly oil grates when not being used regularly.

When handling grates, grids, or radiants on the GLOBE GCB36G-SR, always use insulated gloves.

No, do not hose down, immerse, or pressure wash any part of the GLOBE GCB36G-SR, excluding the catch tray.

No, the GLOBE GCB36G-SR does not contain any user serviceable parts. Repairs should be carried out by qualified technicians.

Do not permit fans to blow directly at the GLOBE GCB36G-SR. Avoid open windows next to the sides or back, and avoid wall type fans which create air cross-currents.

Turn the burners of the GLOBE GCB36G-SR on about 15 to 20 minutes before cooking for preheating.

Each valve controls the gas flow to the burner on the GLOBE GCB36G-SR. For different temperature settings, adjoining areas should be set at progressively higher temperatures using the lowest temperatures on the outside burners.

Operators of the GLOBE GCB36G-SR should be over 18 years old, adequately trained, supervised, and have read and understood the instruction manual.

No, the use of attachments not recommended or sold by the manufacturer may cause fire, injury, or death when using the GLOBE GCB36G-SR.

No, the burners, cooking grates, and outside surfaces of the GLOBE GCB36G-SR will become hot after use. Use caution when touching the unit.

Always turn off the GLOBE GCB36G-SR when servicing or adjusting any parts or attachments.

Always keep hands, hair, and clothing away from the heating source of the GLOBE GCB36G-SR.

The GLOBE GCB36G-SR must be installed under proper ventilation as required per local code.

No, never bypass, alter, or modify the GLOBE GCB36G-SR in any way from its original condition. Doing so creates hazards.

Yes, the appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psi (3.45 kPa).

Do not operate the GLOBE GCB36G-SR with a damaged or leaking gas line, ignitor, or valves, or if the unit is dropped or damaged in any manner.

No, do not use the GLOBE GCB36G-SR outdoors.

Pipe threading compound used on the GLOBE GCB36G-SR must be resistant to the action of liquefied petroleum gases.