GLOBE GCB24G-SR (01) PDF Document

Owners should not permit anyone to touch the GLOBE GCB24G-SR unless they are over 18 years old, are adequately trained and supervised, and have read and understood the manual.

The GLOBE GCB24G-SR must be operated on a solid, level, nonskid surface that is nonflammable and away from sinks and water hazards.

The GLOBE GCB24G-SR requires non-combustible clearances of 6 inches on the sides, 6 inches at the rear, and 4 inches from the floor.

Screw the legs into the permanently fastened nuts on the four corners of the GLOBE GCB24G-SR and tighten by hand. The legs must be installed to adequately provide proper ventilation to the unit.

If you smell gas, immediately shut off the main gas valve to the GLOBE GCB24G-SR, extinguish all heat and flames, and call emergency services.

No, you should not attempt to repair or convert any gas types on your own. Repairs and conversions for the GLOBE GCB24G-SR are to be made solely by an authorized servicer.

Do not use an open flame to check for leaks. Check all gas piping for the GLOBE GCB24G-SR for leaks with a soap and water solution before operating the unit.

Turn the burners of the GLOBE GCB24G-SR on about 15 to 20 minutes before cooking for preheating. When first heated, it will smoke until manufacturing oil and storage dust are burned off. An hour at maximum for all burners is usually sufficient.

Step 1. Make sure all knobs are in the OFF position.

Step 2. The main gas valve should be CLOSED/OFF for five minutes prior to lighting pilots to clear any existing gas.

Step 3. Turn the main gas valve to ON/OPEN.

Step 4. Light and hold an ignition source at the pilot of the GLOBE GCB24G-SR. When the flame is established, remove the ignition source. Repeat this for each burner.

Step 5. Turn each burner knob ON.

From the opening in the front panel of the GLOBE GCB24G-SR, use a screwdriver and turn the pilot valve screw counterclockwise to increase the flame height. The pilot flame should be as small as possible but large enough to guarantee reliable ignition.

Place the top cooking grates of the GLOBE GCB24G-SR with the grid bars angled toward the front, or place the grid bars flat. When placed angled toward the front, the grooves on top will guide excess fat drippings into the grease trough.

Use a clean cloth and a non-abrasive cleaner to clean the stainless steel body of the GLOBE GCB24G-SR. Wipe the polished areas with a soft cloth daily.

Step 1. Place grates on the GLOBE GCB24G-SR with grid bars horizontal, facing down.

Step 2. Turn the broiler on for approximately 45 minutes.

Step 3. Turn off the broiler and allow it to cool for 20 minutes.

Step 4. Clean top and bottom surfaces of the grate with a wire brush to remove animal fats and carbonized grease.

Step 5. Clean channels on grates with a scraper.

Step 6. Remove grates and clean the top surface of radiants with a wire brush.

Do not cover the top of the grates grid during a burn off operation on the GLOBE GCB24G-SR. Restricting the airflow may cause them to warp and will cause damage to the valves, the knobs, and the front panel decal.

Once the GLOBE GCB24G-SR has cooled, remove the catch tray by pulling it forward and discard the waste, grease, debris, and crumbs at least daily.

Close the gas valve to the GLOBE GCB24G-SR to shut off the gas. Clean in place with a wire brush, or clean gas ports with a sharp-pointed metal instrument. Alternatively, the burners may be removed and washed in soapy water for 15 to 20 minutes.

Check if the main gas line is closed and open the valve. Ensure the pilot light is lit by igniting it. If the cause is unknown, call for service.

The adjustment knob for the GLOBE GCB24G-SR may be turned up or down. Adjust the flame with the control knob to your desired level.

The flame may be too low; adjust the pilot light flame height. If the pilot tube is clogged, it needs to be replaced by calling for service.

There may be a main gas line leak. Turn off the main gas valve to the GLOBE GCB24G-SR immediately. Do not light flames, ignite anything, or turn on any electrical switches. Call the fire department if needed and call for service.

Slow heating is often caused by carbon build up. Ensure that the burners of the GLOBE GCB24G-SR are kept clean and free from carbon build up or debris.

The GLOBE GCB24G-SR does not contain any user-serviceable parts. Repairs should be carried out by qualified technicians.

No, do not use the GLOBE GCB24G-SR outdoors.

No, never leave the GLOBE GCB24G-SR on overnight.

The burners, cooking grates, and outside surfaces of the GLOBE GCB24G-SR will become hot after use. Use caution when touching the unit and allow it to cool down before cleaning.

No, never use the GLOBE GCB24G-SR as a heating source.

When handling grates, grids, or radiants from the GLOBE GCB24G-SR, always use insulated gloves to prevent burns.

No, do not use any abrasive or flammable cleaning fluids on the GLOBE GCB24G-SR. Also, do not use scrubber pads or steel wool.

Check the regulator on the GLOBE GCB24G-SR monthly to make sure the vent is open and not blocked in any way. Blockage can cause variations in pressure and affect unit performance.

Once the GLOBE GCB24G-SR has cooled, remove the cast iron grates, lift and rock the back support brace toward you, and lift it up and around the back support pins to clean and de-grease it.

Angle the long lead edge of the brace down around the support pins on the GLOBE GCB24G-SR and rock it around the pins until it is seated flat on the unit’s back ledge.

The GLOBE GCB24G-SR must be installed under proper ventilation as required by local codes to safely manage combustion and exhaust air.

Never use cleaners containing chlorine, iodine, ammonia, or bromine chemicals on the GLOBE GCB24G-SR as these will deteriorate the stainless steel.

Do not slide the GLOBE GCB24G-SR with legs mounted; lift the unit if it is necessary to move it.

The space between the legs at the bottom of the GLOBE GCB24G-SR admits combustion air. Do not block this space.

The cooking grates, cast iron radiants, and char rock grids of the GLOBE GCB24G-SR are heavy duty cast iron which will oxidize if emerged in water. Lightly oil these parts when not being used regularly.

The supplied gas pressure regulator for the GLOBE GCB24G-SR is factory set at 6 inches water column for Natural gas or 10 inches water column for L.P. gas.

Do not permit fans to blow directly at the GLOBE GCB24G-SR. Avoid open windows next to the sides or back, and avoid wall type fans that create air cross-currents within the room.

Sufficient air is needed to compensate for the amount of air removed by any ventilating system. Otherwise, a subnormal atmospheric pressure will occur for the GLOBE GCB24G-SR, affecting operation and causing undesirable working conditions.

Save the packaging material and contact the carrier within 15 days of delivery. Immediately contact service or your local dealer for the GLOBE GCB24G-SR.

Before operating the GLOBE GCB24G-SR, it should be checked to see that it is sitting level. Adjust the four feet to level the charbroiler.

The pilot of the GLOBE GCB24G-SR can be reached through the holes on the front of the unit or through the top grate, by removing the radiant or the char rocks before attempting to light.

Turn the knob to the ON position. Then back off to the desired flame level. The range of adjustment on the GLOBE GCB24G-SR is virtually infinite between ON and OFF.

If different temperature settings are to be used on the GLOBE GCB24G-SR, adjoining areas should be set at progressively higher temperatures, using the lowest temperatures on the outside burners.

Installation of the GLOBE GCB24G-SR should comply with all local codes, as local codes regarding installation and ventilation vary greatly by area.

All major parts of the GLOBE GCB24G-SR, except the burners, are removable through the front if the gas line is disconnected.

The catch tray of the GLOBE GCB24G-SR should be cleaned per use or at least daily.

Use a clean cloth to wipe down the controls and knobs of the GLOBE GCB24G-SR daily.

If the catch tray of the GLOBE GCB24G-SR is permitted to fill too high, grease and debris are likely to accumulate under the unit.

Commissioning of the GLOBE GCB24G-SR is the thorough and methodical testing of the equipment, sub systems, and systems to ensure that the final product functions properly and safely at the work site.

The GLOBE GCB24G-SR and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of ½ psi.