Free English AUTEL MAXICOM MK908PRO (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD AUTEL MAXICOM MK908PRO (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What are the safety requirements for operating the AUTEL MAXICOM MK908PRO in a service area?
Always perform automotive testing in a safe environment. Wear safety eye protection that meets ANSI standards. Keep clothing, hair, hands, tools, and test equipment away from all moving or hot engine parts. Operate the vehicle in a well ventilated work area, as exhaust gases are poisonous.
How should the vehicle be prepared before using the AUTEL MAXICOM MK908PRO?
Put the transmission in PARK for automatic transmission or NEUTRAL for manual transmission and make sure the parking brake is engaged. Put blocks in front of the drive wheels and never leave the vehicle unattended while testing.
What precautions should be taken when working around the engine of a vehicle being tested with the AUTEL MAXICOM MK908PRO?
Be extra cautious when working around the ignition coil, distributor cap, ignition wires and spark plugs. These components create hazardous voltages when the engine is running.
How should test equipment be cleaned when used with the AUTEL MAXICOM MK908PRO?
Keep the test equipment dry, clean, free from oil, water or grease. Use a mild detergent in a clean cloth to clean the outside of the equipment as necessary.
What are the rules regarding driving while using the AUTEL MAXICOM MK908PRO?
Do not drive the vehicle and operate the test equipment at the same time. Any distraction may cause an accident.
How do I prevent damaging the vehicle battery when using the AUTEL MAXICOM MK908PRO?
To avoid damaging the test equipment or generating false data, make sure the vehicle battery is fully charged and the connection to the vehicle DLC is clean and secure.
Where should the AUTEL MAXICOM MK908PRO test equipment be placed?
Do not place the test equipment on the distributor of the vehicle. Strong electro magnetic interference can damage the equipment.
What are the components of the AUTEL MAXICOM MK908PRO system?
There are two main components to the AUTEL MAXICOM MK908PRO system:
1. AUTEL MAXICOM MK908PRO Display Tablet: The central processor and monitor for the system.
2. Vehicle Communication Interface: The device for accessing vehicle data.
How do I power on the AUTEL MAXICOM MK908PRO display tablet?
Use the Lock/Power Button. It turns the device on and off with a long press, or locks the screen with a short press.
What is the function of the power LED on the AUTEL MAXICOM MK908PRO display tablet?
The power LED indicates battery level and charging system status.
How do I use the AUTEL MAXICOM MK908PRO display tablet hands free?
Use the collapsible stand, which extends from the back of the device to allow hands free viewing of the display tablet.
What ports are available on the AUTEL MAXICOM MK908PRO display tablet?
The ports available include the DC Power Supply Input Port, Headphone Jack, USB Port, HDMI port, and Mini USB Port.
How can I identify the status of the Vehicle Communication Interface on the AUTEL MAXICOM MK908PRO?
The Vehicle Communication Interface features several LED indicators:
1. Power LED: Lights solid green when the device is powered on.
2. Vehicle LED: Blinks green when the device is communicating with the vehicle’s network.
3. Error LED: Lights solid red when a serious hardware failure occurs, or blinks red when updating software or firmware.
4. BT LED: Lights solid green when the device is connected with the display tablet through wireless BT communication; also blinks green when data is transmitted.
5. USB LED: Lights solid green when the device is properly connected and communicating with the display tablet via the USB cable.
What are the status LED indicators for the J2534 ECU Programming Device used with the AUTEL MAXICOM MK908PRO?
The J2534 ECU Programming Device features the following LED indicators:
1. Vehicle LED: Blinks green when the device is communicating with the vehicle’s system.
2. Connection LED: Lights solid green when the device is properly connected with the display tablet via the USB cable or lights solid blue via wireless BT connection.
3. Power LED: Lights solid green when the device is powered on.
What is the critical warning regarding the use of the J2534 ECU Programming Device with the AUTEL MAXICOM MK908PRO?
Do not disconnect the programming device while the vehicle LED is on. If the flash programming procedure is interrupted while the vehicle’s ECU is blank or only partially programmed, the module may be unrecoverable.
How do I connect the main cable to the AUTEL MAXICOM MK908PRO Vehicle Communication Interface?
Connect the main cable’s female adapter to the Vehicle Data Connector on the unit and tighten the captive screws.
How do I connect the AUTEL MAXICOM MK908PRO to a vehicle?
Connect the cable’s 16 pin male adapter to the vehicle’s DLC, which is generally located under the vehicle dash.
How do I start the AUTEL MAXICOM MK908PRO for vehicle diagnosis?
Power up the display tablet, ensuring it has a charged battery or is connected to the DC power supply.
How do I pair the AUTEL MAXICOM MK908PRO display tablet with the VCI device?
The display tablet and the VCI device are configured to automatically synchronize with each other when you first use them, so there is no need to perform any pairing procedure.
How do I know if the AUTEL MAXICOM MK908PRO is ready to start vehicle diagnosis?
When the VCI device is properly connected to the vehicle and the display tablet, the VCI status button at the bottom bar on the display screen shows a green tick, indicating the platform is ready to start vehicle diagnosis.
Does the AUTEL MAXICOM MK908PRO support automatic synchronization?
Yes, the display tablet and the VCI device are configured to automatically synchronize with each other when you first use them, so there is no need to perform any pairing procedure.
What is the first step to using the AUTEL MAXICOM MK908PRO?
Connect the main cable’s female adapter to the Vehicle Data Connector on the VCI unit, and tighten the captive screws.
What should I do if the J2534 ECU Programming Device vehicle LED is on during an update?
Do not disconnect the programming device while the vehicle LED is on, as this could make the vehicle’s ECU unrecoverable.
How do I verify the power status of the AUTEL MAXICOM MK908PRO?
The power LED on the tablet indicates battery level and charging system status. For the VCI units, the power LED will light solid green when the device is powered on.
Can I use the AUTEL MAXICOM MK908PRO while driving?
No, do not drive the vehicle and operate the test equipment at the same time. Any distraction may cause an accident.
What type of cloth should be used to clean the AUTEL MAXICOM MK908PRO?
Use a clean cloth with a mild detergent to clean the outside of the equipment as necessary.
How do I ensure the safety of others while using the AUTEL MAXICOM MK908PRO?
Always perform automotive testing in a safe environment, use proper ventilation, and ensure the vehicle is secured in park or neutral with the parking brake engaged and wheels blocked.
Is a fire extinguisher required when operating the AUTEL MAXICOM MK908PRO?
Yes, keep a fire extinguisher suitable for gasoline, chemical, and electrical fires nearby.
How do I turn on the AUTEL MAXICOM MK908PRO display tablet?
Use the Lock/Power Button on the tablet with a long press.
How do I lock the screen of the AUTEL MAXICOM MK908PRO?
Use the Lock/Power Button with a short press to lock the screen.
What does a red light on the VCI Error LED indicate for the AUTEL MAXICOM MK908PRO?
It indicates a serious hardware failure or, if blinking, that the device is updating software or firmware.
What does it mean when the AUTEL MAXICOM MK908PRO VCI status button has a green tick?
It indicates that the VCI device is properly connected to the vehicle and the display tablet, and the platform is ready to start vehicle diagnosis.
How should the transmission be set when using the AUTEL MAXICOM MK908PRO?
Put the transmission in PARK for automatic transmission or NEUTRAL for manual transmission.
What should I do if I am using the AUTEL MAXICOM MK908PRO and need to leave the vehicle?
Never leave the vehicle unattended while testing.
What is the purpose of the VCI unit used with the AUTEL MAXICOM MK908PRO?
The Vehicle Communication Interface is the device used for accessing vehicle data.
What specific components on the engine are hazardous when using the AUTEL MAXICOM MK908PRO?
The ignition coil, distributor cap, ignition wires, and spark plugs are hazardous as they create high voltages when the engine is running.
Are there special storage conditions for the AUTEL MAXICOM MK908PRO?
Keep the test equipment dry, clean, and free from oil, water, or grease.
Does the AUTEL MAXICOM MK908PRO require a stable vehicle power source?
Yes, ensure the vehicle battery is fully charged and the connection to the vehicle DLC is clean and secure to avoid damaging the test equipment or generating false data.
How can I prevent electro magnetic interference with the AUTEL MAXICOM MK908PRO?
Do not place the test equipment on the distributor of the vehicle, as strong electro magnetic interference can damage the equipment.
Is the AUTEL MAXICOM MK908PRO display tablet battery-powered?
Yes, it has a built-in battery, though you should ensure it is charged or connected to the DC power supply during operation.
What are the warning signs regarding the J2534 ECU Programming Device for the AUTEL MAXICOM MK908PRO?
The most critical warning is to not disconnect the device while the vehicle LED is on to avoid rendering the vehicle’s ECU unrecoverable.
How do I ensure the connection to the vehicle is secure for the AUTEL MAXICOM MK908PRO?
Connect the main cable’s female adapter to the Vehicle Data Connector on the unit and tighten the captive screws.
Does the AUTEL MAXICOM MK908PRO have a microphone?
Yes, the display tablet includes a microphone.
Does the AUTEL MAXICOM MK908PRO display tablet have a camera?
Yes, the display tablet features a camera and a camera flash.
What is the ambient light sensor on the AUTEL MAXICOM MK908PRO used for?
It detects ambient brightness.
What is the function of the loudspeaker on the AUTEL MAXICOM MK908PRO?
It provides audio output from the system.
Can I use headphones with the AUTEL MAXICOM MK908PRO?
Yes, the display tablet has a dedicated headphone jack.
What is the purpose of the HDMI port on the AUTEL MAXICOM MK908PRO?
The HDMI port is for high definition multimedia interface output.
Does the AUTEL MAXICOM MK908PRO support USB connections?
Yes, the tablet features both a standard USB port and a Mini USB port.
How do I verify if the VCI is communicating with the vehicle using the AUTEL MAXICOM MK908PRO?
Observe the vehicle LED on the VCI unit; it will blink green when the device is communicating with the vehicle’s network.
What should I look for on the display tablet when connecting the AUTEL MAXICOM MK908PRO to a vehicle for the first time?
Since the system is designed to synchronize automatically, just ensure that the VCI status button at the bottom bar on the display screen eventually shows a green tick.
Are there any specific safety warnings before operating the AUTEL MAXICOM MK908PRO?
Yes, the user must read the instructions carefully, as failure to do so may cause damage or personal injury and will void the limited product warranty.
CLICK HERE TO DOWNLOAD AUTEL MAXICOM MK908PRO (01) PDF DOCUMENT