GLOBE GCB24G-CR (01) PDF Document

Owners should not permit anyone to touch the GLOBE GCB24G-CR unless they are over 18 years old, are adequately trained and supervised, and have read and understood the manual.

The GLOBE GCB24G-CR must be installed on a solid, level, nonskid surface that is nonflammable.

Yes, the non-combustible clearances for the GLOBE GCB24G-CR are 6 inches on the sides, 6 inches at the rear, and 4 inches from the floor.

Level the GLOBE GCB24G-CR by adjusting the four feet. The feet have an adjustment of one inch.

No, you should never bypass, alter, or modify the GLOBE GCB24G-CR in any way from its original condition as doing so may create hazards.

If you smell gas, immediately shut off the main gas valve, extinguish all heat and flames, and call emergency services.

Check all gas piping for leaks with a soap and water solution. Do not use an open flame to check for leaks on the GLOBE GCB24G-CR.

The main gas valve should be in the closed or off position for five minutes prior to lighting pilots on the GLOBE GCB24G-CR to clear any existing gas.

To ignite the burner, turn the knob to the on position. Then, back off to the desired flame level.

Turn the burners on the GLOBE GCB24G-CR about 15 to 20 minutes before cooking for preheating.

No, do not use abrasive cleaners on the GLOBE GCB24G-CR as this might damage the cabinet finish.

Use a clean cloth and a non-abrasive cleaner to clean the stainless steel body of the GLOBE GCB24G-CR. Wipe the polished areas with a soft cloth.

Do not hose down, immerse, or pressure wash any part of the GLOBE GCB24G-CR, excluding the catch tray. Never use a scrubber pad, steel wool, or abrasive material, or cleaners containing chlorine, iodine, and ammonia or bromine chemicals.

Place the grates on the GLOBE GCB24G-CR with grid bars horizontal and facing down. Turn the broiler on for approximately 45 minutes, then turn it off and allow it to cool for 20 minutes. Clean the top and bottom surfaces with a wire brush to remove animal fats and carbonized grease.

The catch tray or drawer on the GLOBE GCB24G-CR is removed by pulling forward.

The catch tray on the GLOBE GCB24G-CR should be cleaned per use or at least daily.

Check if the main gas line is closed and open the valve. If the pilot light is not lit, ignite the pilot light. If the cause is unknown, call for service.

If the flame is too low, adjust the pilot light flame height on the GLOBE GCB24G-CR. If the pilot tube is clogged, replace the pilot tube or call for service.

Ensure that the burners of the GLOBE GCB24G-CR are kept clean and free from carbon build up or debris.

No, the GLOBE GCB24G-CR ships from the factory as Natural gas. Conversion must be performed by an authorized servicer. Do not attempt conversion on your own.

Use a clean cloth and a non-abrasive cleaner to clean the stainless steel body of the GLOBE GCB24G-CR and wipe the polished areas with a soft cloth on a daily basis.

Yes, when handling grates, grids, or radiants on the GLOBE GCB24G-CR, always use insulated gloves to prevent burns.

Do not permit fans to blow directly at the GLOBE GCB24G-CR. Avoid open windows next to the unit’s sides or back and avoid wall type fans which create air cross-currents within a room.

Do not cover the top of the grates grid during a burn off operation on the GLOBE GCB24G-CR. Restricting the airflow by covering the grid grates may cause them to warp and cause damage to the valves, the knobs, and the front panel decal.

Main burner ports on the GLOBE GCB24G-CR must be kept clean. Close the gas valve, then clean in place with a wire brush, or clean gas ports with a sharp-pointed metal instrument to insure open ports. The burners may also be removed and washed in soapy water for 15 to 20 minutes as needed.

Make sure the vent on the regulator of the GLOBE GCB24G-CR is open and not blocked in any way on a monthly basis.

Once the GLOBE GCB24G-CR has cooled, remove the cast iron grates, lift and rock the back support brace toward you, and lift it up and around the back support pins to clean and de-grease it.

Angle the long lead edge of the grate back support brace down around the support pins of the GLOBE GCB24G-CR and rock the back support brace around the pins until it is seated flat on the back ledge.

From the opening in the front panel of the GLOBE GCB24G-CR, use a screwdriver and turn the pilot valve screw counterclockwise to increase the flame height.

The space between the legs at the bottom of the GLOBE GCB24G-CR admits combustion air; do not block this space.

The cooking grates on the GLOBE GCB24G-CR are heavy duty cast iron which will oxidize if emerged in water. Lightly oil the grates when not being used regularly.

Place the top cooking grates of the GLOBE GCB24G-CR with the grid bars angled toward the front, as this guides excess fat drippings into the grease trough.

Always turn off the GLOBE GCB24G-CR when not in use. Never leave the charbroiler on overnight.

Never use the GLOBE GCB24G-CR as a heating source.

The GLOBE GCB24G-CR does not contain any user-serviceable parts; do not remove any components or service panels.

Allow the GLOBE GCB24G-CR to cool down after use before dismantling for cleaning, as the unit will be too hot to handle.

The pilot lights on the GLOBE GCB24G-CR have been set at the factory.

If the stainless steel surfaces of the GLOBE GCB24G-CR become discolored, scrub by rubbing only in the direction of the finished grain.

The catch tray on the GLOBE GCB24G-CR collects waste, grease, debris, and crumbs.

No, do not use the GLOBE GCB24G-CR outdoors.

The use of attachments not recommended or sold by the manufacturer for the GLOBE GCB24G-CR may cause fire, injury, or even death.

Do not operate the GLOBE GCB24G-CR with a damaged or leaking gas line, ignitor, or valves, or if the unit is dropped or damaged in any manner; call for service.

The GLOBE GCB24G-CR must be installed under proper ventilation as required per local code, and the unit must not be obstructed behind the flue.

The controls of the GLOBE GCB24G-CR should be wiped down daily.

If cleaning the burners of the GLOBE GCB24G-CR, the main gas valve must be switched to the closed position. After cleaning, the gas line can be switched back to the open position, and the lighting instructions must be followed to relight the pilot lights.

Always install the GLOBE GCB24G-CR in a work area with adequate light and space, and operate it only on a solid, level, nonskid surface.

The GLOBE GCB24G-CR and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of one half psi.

Yes, before operating the GLOBE GCB24G-CR, it should be checked to see that it is sitting level, and the feet should be adjusted if necessary.

The pilot on the GLOBE GCB24G-CR can be reached through the holes on the front of the unit or through the top grate by removing the radiant or the char rocks.

The catch tray on the GLOBE GCB24G-CR collects waste from cooking, and it is crucial to empty it daily to prevent grease from accumulating under the unit.

The pilot flame on the GLOBE GCB24G-CR should be as small as possible, but large enough to guarantee reliable ignition of the burners when the knobs are turned to the on position.

Always keep hands, hair, and clothing away from the heating source of the GLOBE GCB24G-CR.