Free English CASIO HS-6 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD CASIO HS-6 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What should I do before using my new CASIO HS-6 stopwatch for the first time?
A sticker is affixed to the glass of the CASIO HS-6 stopwatch when you purchase it. Be sure to remove the sticker before using the stopwatch.
What are the functions of the main buttons on my CASIO HS-6 stopwatch?
Button A (START/STOP): Press this button to start and stop elapsed time measurement.
Button B (SPLIT/LAP RESET):
• While an elapsed time measurement is in progress, press this button to momentarily freeze a SPLIT or LAP time on the display. Timing continues internally. Press again to display the ongoing time measurement.
• While elapsed time measurement is stopped, pressing this button resets the time to all zeros.
Button C (MODE): Press this button to toggle between the SPLIT time mode and LAP time mode.
What is the difference between SPLIT mode and LAP mode on the CASIO HS-6?
A SPLIT is the time from the start of an event up to any specific point. The SPLIT mode is indicated by a dotted line icon on the display.
A LAP is the time for one segment (lap) of an event. The LAP mode is indicated by a solid line icon on the display.
What is the maximum time my CASIO HS-6 can measure?
The maximum elapsed time that can be measured on the CASIO HS-6 is 9 hours, 59 minutes, 59.99 seconds.
How do I perform a normal time measurement with the CASIO HS-6?
1. Press Button A to start timing.
2. Press Button A again to stop timing.
3. Press Button B to reset the time to zero.
How can I measure net times (accumulated time excluding loss time) with my CASIO HS-6?
This function is useful for timing events while pausing for “lost time” or time-outs.
1. Press Button A to start timing.
2. Press Button A to stop timing (pause for lost time).
3. Press Button A again to resume timing.
4. Press Button A to stop the final accumulated time.
5. Press Button B to reset the time to zero.
How do I measure split times with the CASIO HS-6?
1. Use Button C to select SPLIT mode (indicated by a dotted line icon).
2. Press Button A to start timing.
3. At the end of a segment, press Button B to freeze and display the split time. The stopwatch continues to time internally.
4. Press Button B again to release the display and show the ongoing total time.
5. Repeat steps 3 and 4 for each subsequent split.
6. Press Button A to stop the total time measurement.
7. Press Button B to reset to zero.
How can I time a 1st and 2nd place finish in a race using the CASIO HS-6?
1. Put the stopwatch in SPLIT mode using Button C.
2. Press Button A to start the race.
3. When the first runner finishes, press Button B. The time of the first runner is displayed.
4. When the second runner finishes, press Button A. This stops the timer.
5. Press Button B to display the time of the second runner.
6. Press Button B again to reset the stopwatch to zero.
How do I measure individual lap times with the CASIO HS-6?
1. Use Button C to select LAP mode (indicated by a solid line icon).
2. Press Button A to start timing.
3. At the end of the first lap, press Button B to freeze and display the time for that lap.
4. Press Button B again to release the display and show the ongoing total time.
5. Repeat steps 3 and 4 for each subsequent lap.
6. Press Button A to stop the total time measurement.
7. Press Button B to reset to zero.
CLICK HERE TO DOWNLOAD CASIO HS-6 (01) PDF DOCUMENT