Free English EXSYS EX-1179HMVS (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD EXSYS EX-1179HMVS (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What are the key features of the EXSYS EX-1179HMVS?
The features of the EXSYS EX-1179HMVS include:
Compatible for USB 1.1, 2.0, 3.0, 3.1 & 3.2
Up to 480Mbit/s data transfer rate
All Operating Systems are supported
All ports are Screw Lock
15KV ESD Surge Protection
IP30 compliant
What is included in the delivery package of the EXSYS EX-1179HMVS?
Before connecting the EXSYS EX-1179HMVS to your PC, check the contents of the delivery:
EX-1179HMVS
USB 2.0 Cable (screw lock)
DIN-Rail Kit
Manual
What critical warning should be observed regarding the power connection of the EXSYS EX-1179HMVS?
ATTENTION!!! Never connect power to GND, it will destroy your Hardware!!!
What is the pin assignment for the USB 2.0 A-Port on the EXSYS EX-1179HMVS?
| Pin | Signal | Pin | Signal |
|---|---|---|---|
| 1 | VCC | 3 | DATA+ |
| 2 | DATA- | 4 | GND |
What is the pin assignment for the USB 2.0 B-Port on the EXSYS EX-1179HMVS?
| Pin | Signal | Pin | Signal |
|---|---|---|---|
| 1 | VCC | 3 | DATA+ |
| 2 | DATA- | 4 | GND |
How do I change the jumper settings for power modes on the EXSYS EX-1179HMVS?
The EXSYS EX-1179HMVS comes with the setting Self-Power. You also have the possibility to supply the EXSYS EX-1179HMVS with Bus-Power. To do this, follow these steps:
1. Open the case by removing the four screws on both sides.
2. Set the jumper JP1 from T (Terminal Block) to U (USB).
How do I install the hardware for the EXSYS EX-1179HMVS?
Please follow these installation steps:
1. Connect the USB cable to the USB B-Port at the Hub.
2. Connect the optional power supply into the terminal block at the Hub.
3. Now connect the other end from the USB cable (A-Plug) to the A-Port at your PC.
4. Finally, you can now install the EXSYS EX-1179HMVS on the wall or on a DIN-Rail.
How do I use the Terminal Block push-in mechanism on the EXSYS EX-1179HMVS?
The push-in mechanism of the Terminal Block allows you to push the wire directly into the contact hole and automatically lock it by its internal latching spring.
To remove the wire, you will need a tool (such as a small flat-bladed screwdriver) to release the internal locking spring and remove the wire. If the wire is too soft to be inserted into the contact hole, you will need to loosen the locking cord with the tool, insert the wire, and then release the locking spring to lock the wire.
How do I install the drivers for the EXSYS EX-1179HMVS?
For all operating systems, after the hardware installation, the OS will recognize the device automatically and install the drivers.
How can I verify that the EXSYS EX-1179HMVS driver is installed correctly?
Open the Device Manager. You should see the following new entries under “USB-Controller”:
Generic USB Hub
Generic USB Hub
If you see this or similar information, the device is installed correctly.
What are the instructions for cleaning the EXSYS EX-1179HMVS?
For cleaning, please use only a dry fluff-less cloth and remove the dirt with gentle pressure. In the area of the connectors, please make sure that no fibers from the cloth remain in the connectors.
Attention! Never use a moist or wet cloth for cleaning!
What are the technical specifications of the EXSYS EX-1179HMVS?
| Chip-Set: | Genesys |
| Data Transfer Rate: | 480Mbit/s |
| Connectors: | 7x USB 2.0 A-Port (screw lock), 1x USB 2.0 B-Port (screw lock), 1x Terminal Block 7-48V |
| Hardware System: | USB 1.1, 2.0, 3.0, 3.1 & 3.2 |
| Operating System: | All Operating Systems |
| Operating Temperature: | 32°F to 131°Fahrenheit |
| Storage Temperature: | -40°F to 185°Fahrenheit |
| Rel. Humidity: | 5% to 95% |
| Power: | +7 to +48 Volt |
| Size: | 132,50 x 80,20 x 36,20 mm |
| Weight: | 500g |
CLICK HERE TO DOWNLOAD EXSYS EX-1179HMVS (01) PDF DOCUMENT