BOSCH FLEXIDOME MICRO 3100I NUE-3703-F02 (01) PDF Document

Installation should only be performed by qualified service personnel in accordance with the National Electrical Code (NEC 800 CEC Section 60) or applicable local codes. The BOSCH FLEXIDOME MICRO 3100I NUE-3703-F02 must be supplied only by an external source having an output complying with PS2 or Annex Q conform to IEC 62368-1 and UL62368-1.

Adhere to the following instructions:

To clean the BOSCH FLEXIDOME MICRO 3100I NUE-3703-F02, do not use liquid cleaners or aerosol cleaners.

Do not install the device near any heat sources such as radiators, heaters, stoves, or other equipment (including amplifiers) that produce heat.

Do not spill liquids on the device before installation is completed.

Take precautions to protect the device from power and lightning surges.

Adjust only those controls specified in the operating instructions.

Operate the device only from the type of power source indicated on the label.

Unless qualified, do not attempt to service a damaged device yourself. Refer all servicing to qualified service personnel.

The recommendations for the computer system are:

Computer with Dual core HyperThreading processor or better.

Graphic card with performance that matches or is better than the resolution of the camera.

Windows 10 or later.

Network access.

Google Chrome, Microsoft Edge, or Mozilla Firefox.

Application software, for example, Video Security Client, Bosch Video Client or BVMS.

The unit must have a valid IP address and a compatible subnet mask. By default, DHCP is pre-set to On. Follow these steps:

1. Start the web browser.

2. Enter the IP address of the BOSCH FLEXIDOME MICRO 3100I NUE-3703-F02 as the URL.

3. During the initial installation, confirm any security questions that show.

If a RADIUS server is used for network access control (802.1x authentication), you must configure the device before it can communicate with the network. To configure the device, connect it directly to a computer using a network cable and then set the service-level password.

The BOSCH FLEXIDOME MICRO 3100I NUE-3703-F02 requires a strong password. The password must obey these conditions:

8 to 19 characters in length.

Upper and lower case letters.

Minimum of 1 digit.

Minimum of 1 special character.

The following special characters are not allowed: ‘@’, ‘&’, ‘<', '>‘, ‘:’, ‘+’.

To view a live stream of the selected video channel:

1. On the left side of the browser, expand the Connection group if necessary.

2. Click the Stream drop-down arrow to see the options.

3. Select the stream you wish to view.

Various overlays in the video image provide important status information:

Decoding error: The frame might show artifacts due to decoding errors.

Alarm flag: Indicates that an alarm has occurred.

Communication error: A communication error, such as a connection failure to the storage medium, a protocol violation or a timeout.

Gap: Indicates a gap in the recorded video.

Watermark valid: The watermark set on the media item is valid.

Watermark invalid: Indicates that the watermark is not valid.

Motion alarm: Indicates that a motion alarm has occurred.

Storage discovery: Indicates that recorded video is being retrieved.

On the left side of the browser, expand the Export group if necessary:

1. Select a track in the track list or in the search results.

2. The start and stop date and time are filled for the selected track. If necessary, change the times.

3. In the Time lapse drop-down box, select Original to export the recorded video as its original, or Condensed to export the recorded video condensed to the given output time.

4. In the Location drop-down box, select a target.

5. Click Export to save the video track.

The BOSCH FLEXIDOME MICRO 3100I NUE-3703-F02 has three authentication modes: Password, Certificate, and Active Directory server (AD FS). To create a new user:

1. Click Add in the section below Authentication modes.

2. In the box User, enter a User name (minimum 5, maximum 31 characters).

3. Select the appropriate authorization level Group (live, user, IVA configuration, or service).

4. Select the Type (Password or Certificate).

5. Click Set to confirm and create a new user.

Make sure that recording is stopped before synching to the PC. Enter the current time or click the Sync to PC button to copy your computer’s system time to the camera.

Select the appropriate white balance mode from the drop-down list. Options include:

Click Hold to put ATW on hold and save the current color settings.

In the Installer Menu, you can configure:

Sensor mode: Specifies the base resolution and frame rates (50 Hz: 25 fps or 60 Hz: 30 fps).

Image rotation: Select 0°, 90° (upright), 180°, or 270° (upright).

Mirror image: Select On to output a mirror image.

Camera LED: Enable, Disable, or Auto disable the LED.

HDMI output (HDMI models only): Select resolution or Off.

Analog output (Non-HDMI models): Select aspect ratio format.

Reboot device: Click Reboot to restart.

Restore settings: Click Restore to return settings to defaults (except network).

1. Enter known values for tilt angle, roll angle, height, and focal length.

2. For unknown values, select the Calculate check box.

3. Place calibration elements on the camera image:

Click the vertical line icon to place a vertical line across the image (e.g., door frame, lamp post).

Click the ground line icon to place a line across the ground in the image (e.g., road marking).

Click the angle icon to place an angle on the ground (e.g., parking bay markings).

4. Adjust calibration elements by entering real sizes in the corresponding boxes or dragging the lines/angles in the image.

To configure a profile, click its tab to open its settings page. Settings include:

Recording includes: Select if Metadata should be included.

Standard recordings: Select Continuous, Pre-alarm, or Off.

Stream: Select Stream 1, Stream 2, or I-frames only.

Alarm recording: Select Pre-alarm time (RAM option available) and Post-alarm time.

Alarm stream: Select Stream 1, Stream 2, or I-frames only.

Alarm triggers: Select the alarm type (Analysis alarm) or Virtual alarm sensors.

Click Set to apply changes.

1. Click the profile to be assigned in the Time periods box.

2. Click a field in the table and, while holding down the left mouse button, drag the cursor across all of the fields to be assigned to the selected profile.

3. Click the No recordings profile in the Time periods box to deselect intervals.

4. Use Select All or Clear All buttons for bulk actions.

5. Click Set to save the settings.

6. Click Start to activate the recording schedule.

1. Click a storage medium in the Managed storage media list to select it.

2. Click Edit below the list.

3. Click Format in the new window to delete all recordings in the storage medium.

4. Click OK to close the window.

1. Apply power to the camera.

2. Find the hardware reset button on the camera block (remove the camera bubble to access).

3. Push and hold the reset button for more than 10 seconds. The red LED indicator on the device will begin flashing.

4. Let the camera complete a self-check. When the self-check completes, the red LED will turn off.

5. Search again for the IP address, access the camera via browser, and set the initial password.