BLAUBERG BLABDUCTO 100 (01) PDF Document

The delivery set for the BLAUBERG BLABDUCTO 100 includes the following items:

Fan: 1 piece

Screws and dowels: 4 pieces

User manual: 1 piece

Packing box: 1 piece

When installing and operating the BLAUBERG BLABDUCTO 100, observe all construction, electrical, and technical norms. Key requirements include:

Disconnect the unit from the power supply prior to any connection, servicing, maintenance, and repair operations.

Only qualified electricians with a work permit for electrical units up to 1000 V are allowed for installation.

Check the unit for any visible damage of the impeller, the casing, and the grille before starting installation.

The casing internals must be free of any foreign objects that can damage the impeller blades.

While mounting the unit, avoid compression of the casing as deformation may result in motor jam and excessive noise.

Misuse of the unit and any unauthorized modifications are not allowed.

Do not expose the device to adverse atmospheric agents such as rain or sun.

Transported air must not contain any dust, solid impurities, sticky substances, or fibrous materials.

Do not use the unit in a hazardous or explosive environment containing spirits, gasoline, or insecticides.

Do not close or block the intake or extract vents to ensure efficient air flow.

Do not sit on the unit and do not put objects on it.

Never touch the unit with wet or damp hands.

Precautions must be taken to avoid the back-flow of gases into the room from the open flue of gas or other fuel-burning appliances.

The BLAUBERG BLABDUCTO 100 is designed for exhaust or supply ventilation of small and medium-sized premises and should be used according to these guidelines:

The fan is rated for connection to single-phase AC power mains (220-240 V/50 Hz or 220 V/60 Hz).

Ingress protection rating against access to hazardous parts and water ingress is IPX4 for the mounted product.

The fan is rated for operation at ambient temperatures ranging from +1 °C to +45 °C.

Do not operate the fan outside the specified temperature range.

The unit is rated as a Class II electrical appliance.

The dimensions for the BLAUBERG BLABDUCTO 100 are as follows:

The BLAUBERG BLABDUCTO 100 is designed for vertical or horizontal installation into a round air duct of a matching diameter. Follow these steps for installation:

Step 1. Ensure the power is turned off at the disconnecting device before beginning.

Step 2. In case of vertical mounting, protect the fan against the ingress of rainfall and condensate.

Step 3. Use the mounting bracket to install the fan. Mark the positions for the holes on the mounting surface using the bracket or fan base as a template.

Step 4. Drill the holes and insert the dowels.

Step 5. Secure the fan and bracket to the surface using the provided screws.

Step 6. Connect the 100 mm air ducts to the fan spigots.

Step 7. A qualified electrician must perform the wiring according to the provided wiring diagram, ensuring the connection is made through a disconnecting device with contact separation in all poles.

Step 8. Do not use a metal screwdriver, knife, or similar tools for adjustment operations to avoid damaging the circuit board.

Technical maintenance for the BLAUBERG BLABDUCTO 100 should be performed at least once every 6 months. Follow these steps:

Step 1. Disconnect the fan from the power mains and take measures to prevent unintentional power-up.

Step 2. Remove the fan from the air ducts if necessary to access all surfaces.

Step 3. Clean the surfaces of the fan from dust and dirt using a soft brush or cloth.

Step 4. Check the reliability of the electrical connections.

Step 5. Warning: Do not allow water or any liquid to come into contact with electric components during cleaning.

Step 6. Reinstall the unit and reconnect it to the power mains after maintenance is complete.

If you encounter issues with your BLAUBERG BLABDUCTO 100, refer to the table below for possible reasons and solutions:

Connection to the mains for the BLAUBERG BLABDUCTO 100 must meet the following criteria:

The connection must be made through a disconnecting device integrated into the fixed wiring system.

The disconnecting device must have contact separation in all poles that allows for full disconnection under overvoltage category III conditions.

If the supply cord is damaged, it must be replaced by the manufacturer, a service agent, or similarly qualified persons to avoid safety hazards.

If any unusual oscillating movements occur, immediately stop using the appliance and contact qualified personnel.

The designation key for the BLAUBERG BLABDUCTO 100 breaks down as follows:

Fan series: BLABDUCTO

Spigot diameter: 100 mm

Voltage options: 220-240 V/50 Hz (Standard) or 220 V/60 Hz (Specified in parentheses if applicable).