BLAUBERG BRICE 150 (01) PDF Document

Please adhere to the following safety instructions when using the BLAUBERG BRICE 150:

• Do not modify internal wiring, as unpredictable accidents may occur.

• Do not place fingers or stick objects on the air inlet or outlet, as this may cause injury.

• Prohibit placing obstacles near the air outlet and air inlet, as this may cause fire or damage to this product.

• Do not turn your eyes towards the air outlet (especially during startup), as garbage and other debris may fly out and cause eye injuries.

• The building structure for installing this product must be firm and secure; an unstable building structure may cause the product to fall and cause injury.

• When lifting this product, please pay attention to the center of gravity balance. Only when confirming the balance of the center of gravity of this product can it be lifted upwards; otherwise, it may cause the product to fall and cause injury.

• Inspection and maintenance work must be carried out by professional personnel, as unpredictable accidents may occur.

• Please wear protective tools such as gloves during inspection, as this may cause injury.

• When performing maintenance (dismantling the inspection panel), attention should be paid to the falling of dirt, dust, or insects, which may enter the eyes.

• During inspection, prevent components, tools, etc. from falling from a height, as this may cause injury to personnel.

• In terms of electrical engineering, construction must be carried out in accordance with the electrical schematic and local wiring rules. Improper wiring may cause electrical measurement or fire hazards.

• Prohibition of modification and splitting of this product, as unpredictable changes may occur.

• Do not use power sources other than the rated voltage of this product, as this may cause fire or damage to this product.

• When gas leakage occurs, please open doors and windows to allow indoor air circulation. It is prohibited to open or close this product, as it may generate electric sparks and cause explosions.

• In terms of electrical, piping, and installation engineering, qualified professionals must be commissioned for installation. Imperfections in the installation project may lead to unpredictable accidents.

• When hanging the body from the ceiling, the bolts must be used in the specified quantity and diameter and must be tightened. Failure to tighten the bolts may cause the product to fall and cause injury.

• After installation, the load of the air duct must not fall on the machine, which may cause injury due to the machine body falling due to excessive product load.

• When checking, the power must be cut off, as this may cause injury or electric shock.

• Cease use immediately in case of abnormalities (sound, vibration, odor), as unpredictable accidents may occur.

• For special purposes, please fully confirm suitability. The use for food, animals and plants, precision instruments, and art under special conditions may lead to quality deterioration.

• During inspection, even if the power is turned off, the fan will still run for a short period of time. Please confirm that the fan has completely stopped running before conducting the inspection, as people or objects caught in the moving parts may cause injury.

• Please take appropriate measures to prevent gas from flowing back into the room from open airways or other open flame equipment, as this may cause smoke reflux.

The packing list for the BLAUBERG BRICE 150 includes:

3.1. Ventilation fan – 1 unit

3.2. Fixed screws – 4 pieces

3.3. User Manual – 1 copy

3.4. Packaging box – 1 piece

The technical parameters are as follows:

The dimensional parameters are as follows (Unit: mm):

Explanation:

1. Dimensions in millimeters.

2. Manual measurement of dimensions may have certain errors; please refer to the actual product.

• Transportation equipment: Any vehicle can be used for transportation without being damaged by climate and machinery.

• Loading and unloading handling: A crane can be used for handling to reduce mechanical damage. When loading and unloading, the transportation and loading and unloading operations should be carried out in accordance with the type of goods of this product.

• The storage equipment is packaged in its original factory and stored in a dry and ventilated environment.

• Storage environment: It should be stored in an environment with stable temperature and humidity, and the ambient temperature should be between +5 °C and +40 °C.

• Avoid storage in environments that may cause mechanical damage.

• Do not store items that may cause corrosion and damage to the insulation together.

7.1.1 First, a circular hole needs to be made in the wall. For the Brice 150 model, it is recommended to make a hole with a diameter of 150-160mm.

7.1.2 Then, remove the plastic clip on the back of the main unit and unscrew the screws at the bottom to take off the front panel.

7.1.3 Place the main body into the hole in the wall.

7.1.4 Use four plastic expansion bolts to fix the main unit onto the wall.

7.1.5 Install the front panel and tighten the fixing screws at the bottom of the panel.

7.1.6 Connect the power cable to the power source.

7.1.7 The installation process for a gypsum board ceiling is the same as wall installation.

7.2.1 First, a circular hole needs to be made in the glass. For the Brice 150 model, it is recommended to make a hole with a diameter of 150-160mm.

7.2.2 Then, remove the plastic clip on the back of the main unit.

7.2.3 Place the machine into the hole in the glass.

7.2.4 Install the plastic clip on the back of the main unit to securely fix the machine onto the glass.

7.2.5 Connect the power cable to the power source.

8.1 The product is not suitable for individuals with disabilities, intellectual disabilities, or mental disorders, or those who lack insurance or common sense (including children) for maintenance and use, unless used under the supervision or guidance of a guardian. It should be ensured that children do not play with this product as a toy.

8.2 This product shall not be used to discharge toxic or explosive substances and gases.

8.3 During installation, a full pole disconnecting device with a contact distance of no less than 3mm should be installed in the power supply line.

8.4 When exchanging air in a room using gas appliances, an additional sufficiently large air inlet should be installed, and the size of the air inlet should be set according to the requirements of the gas appliance user manual (gas reflux indoors may cause carbon monoxide poisoning).

8.5 If the product is installed on a wall and the rear end of the machine is connected to an aluminum foil duct or similar air duct, the air duct must be tilted downwards by at least 1/100 to prevent rainwater or frozen water from flowing back into the ventilation fan housing.

8.6 In winter, when using this product to supply indoor air and heating, there is a possibility of condensation on the joints and the outer surface of the body. Insulation treatment is required.

8.7 This product is suitable for outdoor environments with a temperature range of -5 °C to 40 °C. When the outdoor temperature exceeds this range, it is not recommended to use this product, otherwise there is a risk of condensation or frost.

8.8 Due to the weight of the body and the installation on the ceiling, attention should be paid to avoiding installation on the ceiling with insufficient load-bearing capacity.

8.9 The power cord diameter must be greater than 2.0mm.

Regular cleaning should be carried out using cotton or soft cloth dipped in soap for cleaning. Liquids that corrode plastics such as gasoline should be prohibited, and the impeller should not be touched or pressed.

If there is abnormal noise, odor, or the impeller does not rotate when powered on, the power should be immediately disconnected and handed over to professional personnel for maintenance.

The electrical connections for the BLAUBERG BRICE 150 are as follows, for a AC220V-50Hz power source:

• L (Live): Brown wire

• N (Neutral): Blue wire

• GND (Ground): Yellow/Green wire

These wires connect to the motor. A Thermal Fuse is installed on the live (Brown) wire circuit before the motor.

The name and content of harmful substances in the product are as follows:

This table has been prepared in accordance with the provisions of SJ/T 11364.

O: Indicates that the content of the hazardous substance in all homogeneous materials of the component is within the limit requirements specified in GB/T 26572.

X: Indicates that the content of the hazardous substance in at least one homogeneous material of the component exceeds the limit requirements specified in GB/T 26572.

The years in this symbol refer to the “Environmental Protection Service Life” applicable to electronic and electrical products.

In accordance with the safety and usage precautions recorded in the user manual, and without any other legal or regulatory exemptions, the harmful substances in the product will not leak or mutate within the 10 years from the production date. The use of this product will not cause serious pollution to the environment or cause serious damage to the user’s personal and property.

The “environmentally friendly usage period” is not a safe usage period. It is especially different from the limited usage period based on factors such as electrical performance safety and electromagnetic safety.

When the product is discarded after appropriate use, it is hoped to be handled in accordance with relevant laws or regulations on the recycling or reuse of electronic and electrical products.

Note: This period is the “environmental protection use period” and not the quality assurance period of the product.