ASPIRE SPRYTE (01) PDF Document

The ASPIRE SPRYTE package contains the following items:

1 Spryte device

2 Extra O rings

2 Coils (1*1.8Ω & 1*1.2Ω for Nic Salt)

1 Micro USB Cable

1 User Manual

The specifications for the ASPIRE SPRYTE are as follows:

Spryte Pod capacity: 2ml

Spryte coil is interchangeable with original CE5 BVC coils

Built-in Battery Capacity: 650mAh

Dimensions: 108*26*26mm

Adjustable airflow

Coil resistance: 1.8ohm

Coil type: Nichrome

Easy bottom fill

Output wattage: 12W

Pressing the fire button five times within two seconds will turn the ASPIRE SPRYTE on or off. The indicator lights will flash blue and red three times to indicate off or on.

Follow these steps to fill the ASPIRE SPRYTE:

1. Pull and remove the pod from the main body of the Spryte.

2. Invert the pod and place the filling bottle/dropper into the pod filling hole.

3. Push down and squeeze the filling bottle/dropper bulb to add your preferred e-liquid into the pod system. (Note: The diameter of the pod refill hole is 2.8mm).

4. Re-insert the pod into the power unit, and push down firmly until it ‘clicks’ into place.

Important Notes:

When using a new coil, let the pod stand for 5 minutes after filling so the cotton can be saturated with e-liquid before use.

Do not let the pod become completely empty. Refill the pod to avoid dry burning or damage to the coil.

To install or replace the coil on the ASPIRE SPRYTE:

1. Pull and remove the pod from the main body of the Spryte.

2. Invert the pod, push down and unscrew to disengage the chimney unit, then remove.

3. Detach the atomizer from the airflow control ring and replace it with a new one.

4. Push down and screw in to relocate the chimney unit back to the pod system. (When relocating the chimney unit, please screw and push down at the same time).

5. Re-insert the pod into the power unit, and push down firmly until it ‘clicks’ into place.

To adjust the airflow of the ASPIRE SPRYTE, please remove the pod and rotate the airflow control ring on the bottom of the Spryte pod.

When the ASPIRE SPRYTE is on, press the fire button and the lights will indicate your current charge:

Above 3.8 volts: The indicator lights will be blue and red.

Between 3.8 and 3.5 volts: The lights will be blue only.

Below 3.5 volts: The lights will become red to remind you that it is time to charge your Spryte.

Charge the ASPIRE SPRYTE via the Micro USB port. The maximum charge current can reach up to 1000mA. When the USB cable is attached, the indicator lights will flash blue and red three times.

While charging, the LED will indicate the charge status:

3.5 volts or less: Red light.

3.5 to 3.8 volts: Blue light.

3.8 volts and above: Both blue and red lights.

Fully Charged: When the Spryte is fully charged, the LED will flash blue and red 20 times then remain off.

The ASPIRE SPRYTE includes the following protective features:

Automatic Cutoff: The preset continuous fire time is 15 seconds. After 15 seconds of continuous firing, the LED lights will flash blue and red 10 times and the Spryte will stop firing. It will fire again when the button is pressed.

Short Circuit Protection: When the Spryte detects a short, it will stop firing, and the LED lights will flash blue and red 3 times.

Low Voltage Protection: When the battery level drops below 3.2V, the Spryte will not function and the LED lights will flash red 15 times.

Overcharge Protection: When the Spryte is fully charged, it will stop charging to prevent overcharging of your battery.

Over Heat Protection: When the temperature of the control board is above 75 °C / 167 °F, the light will remain on blue and red for 3 seconds to remind of overheat and the Spryte will cut off.