Free English ASPIRE X30 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD ASPIRE X30 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What is included in the package for the ASPIRE X30?
The ASPIRE X30 package contains the following items:
- 1* NX30 Mod (2000 mAh)
- 1* Nautilus X Tank Clearomizer
- 1* 1.8 Ohm U-Tech Coil (12W-16W)
- 1* Replacement Pyrex Tube
- 1* Micro USB Cable
- 1* Lanyard
- 1* Warranty Card
- 1* User Manual
How do I fill the tank on the ASPIRE X30?
To fill the ASPIRE X30 tank, follow these top fill instructions:
1. Unscrew and remove the top cap.
2. Squirt E-Liquid into the tank.
3. Re-attach the top cap to your tank and begin to vape.
How do I install or replace the coil on the ASPIRE X30?
To install a coil on the ASPIRE X30, follow these steps:
1. Unscrew the top cap from the tank.
2. Remove the Pyrex tube.
3. Replace the atomizer with a new one.
Important Notes:
When using a new atomizer, let the tank stand for 5 minutes, so the cotton can be saturated with juice before firing.
Do not let the tank become completely empty. Refill the tank to avoid dry burning or damage to the atomizer.
What are the technical specifications of the ASPIRE X30 mod?
The operational specifications for the ASPIRE X30 mod are as follows:
- Wattage Range: 1-30W
- Output Voltage Range: 0.50-8.00V
- Resistance Parameters: 0.2ohm to 3.5ohms
- Continuous Fire Time: 10 seconds
- Charging Port: Micro-USB
- Screen: OLED 0.86 inch
- Dimensions: 22.5*36*60mm
- Battery Capacity: 2000mah
- Battery: Built-in Lipo
What are the button functions and shortcuts on the ASPIRE X30?
The following table outlines the button functions for controlling the ASPIRE X30:
| Action | Function |
|---|---|
| Click fire Button 5 times within 2 seconds | To power the NX30 mod ON. |
| Click fire Button 5 times within 2 seconds | To either Lock or Unlock the device. |
| Click fire Button 3 times quickly | To go into or out of stealth mode. |
| Press “+” / “-“ | To Increase or decrease Wattage or Voltage. |
| Press Fire Button + “+” | To select between VW, VV and Bypass modes. |
| Press Fire Button + “-“ | To Lock or Unlock the mod buttons. |
| Press “+” + “-“ | Press “+” and “-” buttons simultaneously for 2 seconds to rotate the screen. |
How do I charge the ASPIRE X30?
Charging instructions for the ASPIRE X30 are as follows:
Charging is via the Micro-USB charging port. Maximum charging current can reach up to 1A.
Connect the mod to your charger. The screen will flash a battery icon. When the charge level reaches 4.2V or when it is fully charged, the mod will stop charging and the screen will turn off.
The mod supports pass-through charging. To lengthen the life of the mod, it is not recommended to vape while charging (pass-through).
CLICK HERE TO DOWNLOAD ASPIRE X30 (01) PDF DOCUMENT