ALLIANCE AWN63RSN115CW14 (01) PDF Document

To enter the Factory Test Procedure on the ALLIANCE AWN63RSN115CW14, follow these steps:

1. Disconnect electrical power from the unit.

2. Reconnect electrical power to the unit.

3. Wait about 10 seconds.

4. Turn the Cycle Selection knob to the opposite of Normal Eco and stay on that selection for at least one second.

5. Press and hold the Start/Pause button.

6. Change the Cycle Selection knob to Normal Eco within 5 seconds.

7. Stay on Normal Eco for at least one second to enter the Factory Test Mode.

8. Press the Start/Pause button to advance through the sequence of test steps.

The Factory Test Procedure for the ALLIANCE AWN63RSN115CW14 includes the following test steps:

You can test the mixing valve solenoids using an Ohm meter on the ALLIANCE AWN63RSN115CW14. Resistance readings slightly out of the given ranges may be due to meter conditions and do not necessarily indicate mixing valve failure.

If you encounter a No Hot Water issue with the ALLIANCE AWN63RSN115CW14, check the following items:

1. Ensure the water supply faucet is open.

2. Ensure the water supply is not cold and the hoses are not reversed.

3. Check if the hot water fill hose is kinked.

4. Check if the mixing valve screen or the screen in the outer end of the fill hose nearest the faucet is clogged.

5. Verify if there is proper voltage output from the output board to the hot mixing valve solenoid.

6. Check if the hot solenoid is inoperative and replace the valve if necessary.

7. Inspect the pressure hose for damage or clogs.

8. Check if the temperature selector switch is operating properly.

If you encounter a No Cold Water issue with the ALLIANCE AWN63RSN115CW14, check the following items:

1. Ensure the water supply faucet is open.

2. Check if the cold water fill hose is kinked.

3. Check if the mixing valve screen or the screen in the outer end of the fill hose nearest the faucet is clogged.

4. Verify if there is proper voltage output from the output board to the cold mixing valve solenoid.

5. Check if the cold solenoid is inoperative and replace the valve if necessary.

6. Inspect the pressure hose for damage or clogs.

7. Check if the temperature selector switch is operating properly.

If the ALLIANCE AWN63RSN115CW14 does not stop filling at the proper level, consider the following:

1. If there is a Pressure Sensor error (WASH, RINSE LEDs flash 1 time), check for a restricted or clogged pressure bulb or hose and replace the sensor if clear.

2. If there is an overflow error (WASH, RINSE LEDs on continuously), check for a leak in the mixing valve.

3. Check for an air leak in the pressure hose and replace the hose or pressure bulb.

4. Test the mixing valve if it is suspected to be inoperative.

5. Check for siphoning action where the end of the drain hose is lower than the cabinet top of the washer. Install a Siphon Break Kit if necessary.

6. Check if the drain hose fits tightly in the standpipe or drain. Provide an air gap around the drain hose and drain receptacle.

7. Check for water in the pressure hose; blow air through it to remove water or replace the hose.

8. Check for broken, loose, shorted, or incorrect wiring.

To level the ALLIANCE AWN63RSN115CW14, follow these steps:

1. Place a level on the cabinet top and check if the washer is level from side to side and front to back.

2. If not level, tilt the washer back to access the front leveling legs. Loosen the locknuts and adjust the legs by screwing them into or out of the washer base.

3. Once adjusted, tilt the washer forward on the front legs and lower it back down into position to set the rear self-leveling legs.

4. The washer must not rock. When level and stable, tighten the locknuts securely against the bottom of the washer base.

When replacing or reinstalling the drive bell on the ALLIANCE AWN63RSN115CW14, tighten the bolts to these specifications: