ALLIANCE AWN43RSN116TW01 (01) PDF Document

To enter the Factory Test Procedure on the ALLIANCE AWN43RSN116TW01, follow these steps:

1. Disconnect electrical power from the unit.

2. Reconnect electrical power to the unit.

3. Wait about 10 seconds.

4. Turn the Cycle Selection knob to the opposite of Normal Eco. Stay on that selection for at least one second.

5. Press and hold the Start/Pause button.

6. Change the Cycle Selection knob to Normal Eco within 5 seconds or the Start press will be invalid.

7. Stay on Normal Eco for at least one second. The control will enter Factory Test Mode.

The Factory Test Procedure for the ALLIANCE AWN43RSN116TW01 includes the following steps:

You can test the mixing valve solenoids on the ALLIANCE AWN43RSN116TW01 using an Ohm meter. Please note that resistance readings slightly out of the given ranges may be due to meter conditions and do not necessarily indicate mixing valve failure.

To advance the ALLIANCE AWN43RSN116TW01 to the final spin/drain step, follow these steps:

1. Make sure EXTRA RINSE is in the OFF position.

2. Press and hold the START/PAUSE button. After about three seconds the current cycle status light will turn off.

3. Continue holding the START/PAUSE button for another 7 – 8 seconds until the SPIN light comes on then release the button.

4. If the lid was unlocked, the LID LOCK light will come on and the lid will lock. Once locked, the machine will start to drain and spin.

5. After the final spin/drain step the control will reset to normal operation.

For Audio Signals on the ALLIANCE AWN43RSN116TW01: An audio signal will sound for three seconds at the end of each cycle. To turn it off, hold the Extra Rinse button for three seconds. Hold it again for three seconds to turn the signal back on. A one-second tone will sound to confirm that the End of Cycle signal is turned off or on.

Audio signals will sound when a knob selection is changed and when the Start/Pause or Extra Rinse buttons are pressed. To turn them off, hold the Extra Rinse button for 10 seconds. Hold it again for 10 seconds to turn the signals back on. A three-second tone will sound to confirm that these signals are turned off or on.

For Rapid Advance on the ALLIANCE AWN43RSN116TW01: When Rapid Advance is enabled, pressing the START/PAUSE button during Run Mode will advance the current cycle step to the next enabled step.

How to Enter Rapid Advance Mode:

1. Press and hold both the START/PAUSE and EXTRA RINSE button for three seconds. The Status lights will be lit in an upward pattern when rapid advance is turned on.

2. Press START/PAUSE button to advance through the cycle.

3. To exit rapid advance, press and hold both the START/PAUSE and EXTRA RINSE button for three seconds. The lights will be lit in a downward pattern when the signal is turned off.

Follow these steps to adjust the leveling legs on the ALLIANCE AWN43RSN116TW01:

1. Place a level on the cabinet top and check if the washer is level from side to side and front to back.

2. If washer is not level, tilt washer back to access the front leveling legs. Loosen the locknuts and adjust legs by screwing into or out of washer base.

3. Once adjusted, tilt the washer forward on front legs and lower back down into position to set the rear self-leveling legs.

4. Washer must not rock. When washer is level and does not rock, tighten locknuts securely against bottom of washer base. If these locknuts are not tight, washer will not remain stationary during operation.

When replacing or reinstalling the drive bell on the ALLIANCE AWN43RSN116TW01, torque bolts to the following specifications:

If the ALLIANCE AWN43RSN116TW01 is not getting hot water, please check the following:

Is the water supply faucet closed? If yes, open faucet.

Is the water supply cold? If yes, check if hoses are reversed. If they are, connect to proper faucets. If not, check water heater.

Is the hot water fill hose kinked? If yes, straighten or replace hose.

Is the mixing valve screen or screen in outer end of fill hose nearest water supply faucet clogged? If yes, disconnect hot fill hose and clean or replace screen.

Is there proper voltage output from the output board to the mixing valve hot solenoid? If no, replace output board.

Is the hot solenoid inoperative? If yes, replace valve.

Is the pressure hose clogged or damaged? If yes, remove and clean or replace hose.

Is the temperature selector switch operating properly? If no, ohm out selector switch using wiring diagram.

If the ALLIANCE AWN43RSN116TW01 is not getting cold water, please check the following:

Is the water supply faucet closed? If yes, open faucet.

Is the cold water fill hose kinked? If yes, straighten or replace hose.

Is the mixing valve screen or screen in outer end of fill hose nearest water supply faucet clogged? If yes, disconnect cold fill hose and clean or replace screen.

Is there proper voltage output from the output board to the mixing valve cold solenoid? If no, replace output board.

Is the cold solenoid inoperative? If yes, replace valve.

Is the pressure hose clogged or damaged? If yes, remove and clean or replace hose.

Is the temperature selector switch operating properly? If no, ohm out selector switch using wiring diagram.

If the ALLIANCE AWN43RSN116TW01 is vibrating excessively, check the following:

Has the shipping plug been removed from the base? If no, remove plug.

Is there an unbalanced load in the tub? If yes, stop washer, redistribute load, and restart washer.

Are any centering springs broken, disconnected, or in the wrong position? If no, connect or replace centering spring(s). Ensure green springs are in the front two positions.

Is the washer unleveled? If yes, adjust leveling legs. Make sure rear leveling legs are free.

Is the washer installed on a weak, spongy, carpeted, or built-up floor? If yes, relocate washer or support floor to eliminate weak or spongy condition.

Are cabinet screws incorrect or loose? If yes, replace with correct screws or tighten.

Is base damaged (washer was dropped)? If yes, replace base assembly.

Is there lubricant on the pivot dome and/or base friction ring? If yes, remove lubricant or replace parts.

Is the partial liquid-filled balance ring leaking? If yes, replace balance ring.

Is the friction ring broken? If yes, replace friction ring.