FREE ENGLISH ZENITH M30 (01) PDF DOCUMENT.
FREE ENGLISH ZENITH M30 (01) PDF USER GUIDE.
FREE ENGLISH ZENITH M30 (01) PDF USER MANUAL.
FREE ENGLISH ZENITH M30 (01) PDF OWNER GUIDE.
FREE ENGLISH ZENITH M30 (01) PDF OWNER MANUAL.
FREE ENGLISH ZENITH M30 (01) PDF REFERENCE GUIDE.
FREE ENGLISH ZENITH M30 (01) PDF INSTRUCTION GUIDE.
FREE ENGLISH ZENITH M30 (01) PDF REFERENCE MANUAL.
FREE ENGLISH ZENITH M30 (01) PDF INSTRUCTION MANUAL.
FREE ENGLISH ZENITH M30 (01) PDF OPERATING INSTRUCTIONS.
CLICK HERE TO DOWNLOAD ZENITH M30 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What should I do before I begin assembly?
Please identify all parts and hardware pieces before you begin. When laying out parts, place them on a soft surface to prevent scratching.
What safety precautions should be taken before altering a wall surface?
Before cutting, drilling or hammering into any wall surface, verify the location of electrical, plumbing and gas lines. Cutting any of these may cause serious injury. If needed, contact your electrician, plumber or service person.
What is important to know about mounting hardware?
Be sure to select the proper mounting hardware (not included) to support the cabinet, whether mounting to drywall or to wooden studs. We recommend mounting the cabinet directly into studs.
What tools are needed for assembly?
The following tools are needed:
• Screwdriver
• Tape Measure
• Level
• Drill
What parts are included?
| Part | Description | Quantity |
|---|---|---|
| A | Cabinet Body | 1 |
| B | Door | 2 |
| C | Center Door | 1 |
| D | Adjustable Shelf | 3 |
What hardware is included?
NOTE: Hardware components are packaged together in a bag.
| Part # | Description | Quantity |
|---|---|---|
| 1 | Hinge | x 6 |
| 2 | Hinge Screw | x 12 |
| 3 | Shelf Clip | x 12 |
| 4 | Bumper Strip | x 2 |
| 5 | Angle Block | x 3 |
| 6 | Angle Block Screw | x 3 |
| 7 | Screw Cap | x 8 |
How should the adjustable shelves be oriented?
Adjustable shelves should be oriented so that unused holes are not visible during normal use.
How do I mount the cabinet?
1. Remove the adjustable shelves (D) and shelf clips (F) from inside the cabinet body (A).
2. Hold the cabinet body (A) up against the wall in desired final location.
3. Mark locations for the screws on the top hanging rail and bottom of back panel. (We recommend mounting the cabinet directly into studs.)
4. Drill marked spots on the top hanging rail and bottom of back panel.
5. Using the angle block screws (6), fasten angle blocks (5) to the bottom of the cabinet body (A).
6. Hold the cabinet body (A) up in final location. NOTE: Make sure unit is level.
7. Mark locations on wall through drilled holes in the top hanging rail and back panel.
8. Drill marked spots on wall. If screws will not be going directly into studs, insert wall anchors (not included).
9. Attach cabinet body (A) to wall, using appropriate mounting hardware (not included).
10. Insert adjustable shelves (D) in desired locations, using shelf clips (3).
11. Fasten hinges (1) to doors (B,C) with hinge screws (2).
12. Fasten doors (B,C) to cabinet body (A).
13. Place bumpers (4) on cabinet body (A) where it comes in contact with the doors (B,C).
14. Cover screws with screw caps (7).
How do I adjust the hinges?
Hinge Adjustment
Loosen the hinge keyhole screw that secures the hinge to the mounting plate.
Lateral Adjustment Screw
Allows for adjusting the door 2.5mm left or right.
Horizontal Adjustment Screw
Allows for adjusting the door forwards or backwards.
Vertical Adjustment
Allows for adjusting the door up or down.
CLICK HERE TO DOWNLOAD ZENITH M30 (01) PDF DOCUMENT