HEATH ZENITH DUALBRITE 4290 (01) PDF MANUAL

The fixture has several operation modes:

* The Manual mode resets to Auto Mode at dawn.

When first turned on, wait about 1 1/2 minutes for the circuitry to calibrate. The sensor has a 1 1/2 minute warm up period before it will detect motion.

Set the ON-TIME switch on the bottom of the cover plate to TEST.

Set the ON-TIME switch to 1, 5, or 10 minutes.

Manual mode only works at night because daylight returns the sensor to AUTO. To toggle between AUTO and MANUAL MODE, flip the light switch off for 1 second then back on. Manual mode works only with the ON-TIME switch in the 1, 5, or 10 position.

The main features are:

Light comes on when motion is detected.

Automatically turns light off.

Dusk Accent lighting.

Photocell keeps the light off during daylight hours.

The package contents include:

Lantern

Universal Mounting Bracket

Mounting Screws (Includes extra long screw studs for recessed junction box mounting)

Wire Connectors

The light control requires 120 volts AC.

If you want to use Manual Mode, the control must be wired through a switch.

Some electrical codes require installation by a qualified electrician.

If you get confused while switching modes, turn the power off for one minute, then back on. After the calibration time, the control will be in the AUTO mode.

Light comes on half bright for a selected time after dusk (Off, 3 hr., 6 hr., until dawn). Selecting OFF disables this feature. The motion sensing features will continue to work as described in this manual. If motion is sensed, the light turns on full bright for the ON-TIME (1, 5, or 10 minutes) then returns to dim mode.

Estimated Installation Time: 30 minutes.

Items needed for installation (not included):

Phillips and flathead screwdrivers

Pliers

Wire strippers/cutters

Safety glasses

Light bulb

Silicone caulk

For best performance, mount the fixture about 6 feet (1.8 m) above the ground.

Turn power off at circuit breaker or fuse.

1. Remove two nuts.

2. Remove X-Bar.

3. Tighten screws finger tight.

4. Set sensitivity on fixture back to the mid-position.

5. Attach X-Bar to junction box.

You may find it helpful to have an assistant hold the fixture in place while connecting the wires due to its size and weight.

All wiring should be run in accordance with the National Electrical Code through conduit or another acceptable means. Do not connect the RED wire unless you want to control other lights from the motion sensor. Connect the fixture wires to the wires in the junction box. Twist the wires together and secure with wire connectors. Twist the junction box wires and the fixture wires together as shown in the diagrams below. Secure with wire connectors. If you have a metal junction box, you may not need the green “pigtail”. If you are unsure about the grounding method, consult your local building code.

Black to black

White to white

Recommended Grounding Method: Use a green ground “pigtail” (not provided) and twist one end together with the bare fixture wire and the box ground wire. Secure with a wire connector. Secure the other end of the “pigtail” with the GND screw on the mounting plate.

Strip the motion sensor’s red wire and connect to the standard light’s black wire. Connect all white wires together. Total fixture ratings must not exceed 360 Watts (3.0 A).

Strip the red wire in both light fixtures. Connect the red wire of the controlling (Primary) fixture to the red and black wires of the controlled (Controlled) fixture. Connect all white wires together. Total fixture ratings must not exceed 360 Watts (3.0 A).

It is possible to wire two motion lights so that either fixture will turn on both lights at the same time (dual primary system). It is recommended that only people with plenty of electrical experience attempt this configuration. If the dual primary wiring is not done correctly, it can destroy both motion sensing fixtures and void your warranty.

Stuff the wires into the junction box. Make sure none of the wires get pinched. Slide the fixture onto the mounting screws and tighten nuts. Install light bulb (100 Watt maximum). Install the lower glass assembly (if applicable). Secure with decorative screws. After completing the tests, caulk between fixture canopy and mounting surface with silicone weather sealant.

Turn on the circuit breaker and light switch. Switch the on-time to TEST position and DUALBRITE® switch to the OFF position.

Avoid aiming the control at:

Objects that change temperature rapidly, such as heating vents and air conditioners. These heat sources could cause false triggering.

Areas where pets or traffic may trigger the control.

Nearby large, light-colored objects reflecting light may trigger the shut-off feature. Do not point other lights at the sensor.

The detector is less sensitive to motion directly towards it and more sensitive to across motion.

Model 4294 comes with a separate lower arm. Follow the directions below to attach the lower arm:

1. Complete the installation steps above.

2. Using the decorative screws provided, secure the lower arm to the canopy and the bottom of the lower glass assembly as shown.

Walk through the coverage area noting where you are when the lights turn on. Move the sensor head left or right to change the coverage area. Grasp the sensor only as shown and turn the entire sensor. Any other method may damage the sensor. Do not force the sensor past the stopping points.

If you need to change the sensitivity, temporarily remove the fixture and make the adjustment. Too much sensitivity may increase false triggering.

Set the amount of TIME you want the light to stay on after motion is detected. (1, 5, or 10 minutes).

Set the amount of time after dusk you want the lights on accent level.

If the lantern has an open bottom, insert the bulb through the opening and screw into the socket.

If the lantern has a closed bottom, follow these steps to replace the bulb:

1. Place one hand under the lower glass assembly and unscrew the decorative screws holding the lower glass assembly to the top of the fixture.

2. Replace the bulb.

3. Reattach the lower glass assembly to the fixture top using decorative screws.

To prolong the original appearance, clean with clear water and a soft damp cloth only.

Do not use paints, solvents, or other chemicals on this light fixture. They could cause a premature deterioration of the finish.

Do not spray with hose or power washer.

Possible Causes:

1. Light switch is turned off.

2. Bulb is loose or burned out.

3. Fuse is blown or circuit breaker is turned off.

4. Daylight turn-off is in effect (recheck after dark).

5. Incorrect circuit wiring, if this is a new installation.

Possible Causes:

1. Light control may be installed in a relatively dark location.

2. Light control is in Test (Set control switch to an ON-TIME position).

Possible Cause:

1. Light control may be sensing small animals or automobile traffic (Reduce sensitivity).

Possible Causes:

1. The sensor is pointed toward a heat source like an air vent, dryer vent, or brightly painted, heat reflective surface (Reduce sensitivity).

2. Light control is in Manual Mode. (Switch to Auto.)

3. Light control is in DualBrite® mode.

4. Sensitivity is set too high. (Reduce sensitivity.)

Possible Causes:

1. Light control is in the Test mode and warming up (Flashing is normal under these conditions).

2. Heat being reflected from other objects may be affecting the sensor. (Re-aim sensor.)