FREE ENGLISH ZENITH M24 (01) PDF DOCUMENT.
FREE ENGLISH ZENITH M24 (01) PDF USER GUIDE.
FREE ENGLISH ZENITH M24 (01) PDF USER MANUAL.
FREE ENGLISH ZENITH M24 (01) PDF OWNER GUIDE.
FREE ENGLISH ZENITH M24 (01) PDF OWNER MANUAL.
FREE ENGLISH ZENITH M24 (01) PDF REFERENCE GUIDE.
FREE ENGLISH ZENITH M24 (01) PDF INSTRUCTION GUIDE.
FREE ENGLISH ZENITH M24 (01) PDF REFERENCE MANUAL.
FREE ENGLISH ZENITH M24 (01) PDF INSTRUCTION MANUAL.
FREE ENGLISH ZENITH M24 (01) PDF OPERATING INSTRUCTIONS.
CLICK HERE TO DOWNLOAD ZENITH M24 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What should I do before I start assembling the cabinet?
Please identify all parts and hardware pieces before you begin. When laying out parts, place them on a soft surface to prevent scratching.
What safety warning should I be aware of before cutting or drilling into a wall?
Before cutting, drilling or hammering into any wall surface, verify the location of electrical, plumbing and gas lines. Cutting any of these may cause serious injury. If needed, contact your electrician, plumber or service person.
What is important to know about mounting the cabinet?
Be sure to select the proper mounting hardware (not included) to support the cabinet, whether mounting to drywall or to wooden studs. We recommend mounting the cabinet directly into studs.
What tools are needed for assembly?
Based on the images in the PDF, you will need a screwdriver, a tape measure, a level, and a drill.
What parts are included with the cabinet?
| Part Identifier | Part Name | Quantity |
|---|---|---|
| A | Cabinet Body | 1 |
| B | Door | 2 |
| C | Center Door | 1 |
| D | Adjustable Shelf | 3 |
What hardware is included with the cabinet?
| Part Identifier | Part Name | Quantity |
|---|---|---|
| 1 | Hinge | x 6 |
| 2 | Hinge Screw | x 12 |
| 3 | Shelf Clip | x 12 |
| 4 | Bumper Strip | x 2 |
| 5 | Angle Block | x 3 |
| 6 | Angle Block Screw | x 3 |
| 7 | Screw Cap | x 8 |
How is the hardware packaged?
Hardware components are packaged together in a bag.
How should the adjustable shelves be oriented?
Adjustable shelves should be oriented so that unused holes are not visible during normal use.
What are the steps for mounting the cabinet?
1. Remove the adjustable shelves (D) and shelf clips from inside the cabinet body (A).
2. Hold the cabinet body (A) up against the wall in the desired final location.
3. Mark locations for the screws on the top hanging rail and bottom of the back panel. We recommend mounting the cabinet directly into studs.
4. Drill the marked spots on the top hanging rail and bottom of the back panel.
5. Using the angle block screws (6), fasten the angle blocks (5) to the bottom of the cabinet body (A).
6. Hold the cabinet body (A) up in the final location. NOTE: Make sure the unit is level.
7. Mark locations on the wall through the drilled holes in the top hanging rail and back panel.
8. Drill the marked spots on the wall. If screws will not be going directly into studs, insert wall anchors (not included).
9. Attach the cabinet body (A) to the wall, using appropriate mounting hardware (not included).
10. Insert the adjustable shelves (D) in the desired locations, using shelf clips (3).
11. Fasten the hinges (1) to the doors (B,C) with hinge screws (2).
12. Fasten the doors (B,C) to the cabinet body (A).
13. Follow the specific instructions for hinge installation or adjustment.
14. Place bumpers (4) on the cabinet body (A) where it comes in contact with the doors (B,C).
15. Cover the screws with screw caps (7).
How do I adjust the hinges on the doors?
Hinge Adjustment: Loosen the hinge keyhole screw that secures the hinge to the mounting plate.
Lateral Adjustment: The Lateral Adjustment Screw allows for adjusting the door 2.5mm left or right.
Horizontal Adjustment: The Horizontal Adjustment Screw allows for adjusting the door forwards or backwards.
Vertical Adjustment: The Vertical Adjustment allows for adjusting the door up or down.
CLICK HERE TO DOWNLOAD ZENITH M24 (01) PDF DOCUMENT