WINEGARD CONNECT WIFI WF-3000 WHITE (01) PDF MANUAL

WINEGARD CONNECT WIFI WF-3000 WHITE (01) PDF SUMMARY:

What warnings should I be aware of regarding the exterior installation of the Winegard® ConnecT™ WF1?

Do not paint any portion of the Winegard® ConnecT™ WF1, as painting could damage the system and will void the warranty. Do not mount closer than 12 inches from the edge of the roof, or closer than 24 inches from adjacent devices. Do not mount the outdoor unit (ODU) with the cable facing the front of the vehicle.

---

How do I install the antennas on the outdoor unit (ODU)?

Remove each antenna from the protective bag and screw it into an open port on the outdoor unit (ODU). Firmly tighten each antenna by hand. If using a wrench, do not overtighten the antenna as the antennas or housing may become damaged. The antennas should be tightened to 20–25 inch pounds of torque.

---

How do I attach the mounting feet to the outdoor unit (ODU)?

Attach the mounting feet to the unit by threading the provided nuts to the post on the mounting feet. Tighten nuts using an 11/32” wrench.

---

Where should I place the outdoor unit (ODU) on the roof?

Place the unit on the roof in the chosen location, ensuring that the Ethernet cable exits the unit towards the back of the vehicle. Clean the roof where the unit will be mounted to ensure a good seal.

---

How do I secure the mounting feet to the roof?

Using a 1/8” drill bit, pre-drill the holes for each of the screws to hold the mounting feet in place. Add a small bead of manufacturer approved sealant (not provided) to each hole. Drive the screws through the sealant into each hole until tight. Do not overtighten as it will cause the screw to strip. After the mounting feet are secured, add a small amount of approved sealant around the edge of each mounting foot and over each screw.

---

How do I attach the cable entry cover on the ODU?

Place the cable entry cover on the ODU and secure using the provided screw.

---

How do I route the Ethernet cable into the vehicle?

Decide where the indoor unit (IDU) will be mounted inside the vehicle to determine the best location for the Ethernet cable to enter the vehicle. Drill a 3/4” hole through the roof and push the Ethernet cable into the vehicle. Make sure the cable is accessible from the area where the IDU will be located. Add a bead of sealant around the hole for the cable. Place the provided cable entry plate over the hole and cable. Secure cable entry plate in place using the supplied screws. Seal the plate and screws with approved sealant.

---

How do I secure the cable to the roof?

Secure the cable to the roof every 12–16 inches to eliminate excessive cable movement. Seal the cable to the roof between the unit and cable entry plate. Cable clamps (not provided) may need to be used depending on the distance the cable runs across the roof.

---

How do I connect the Ethernet cable to the indoor unit (IDU)?

Connect the Ethernet cable from the ODU to the POE port on the bottom of the IDU.

---

How do I power the indoor unit (IDU)?

Plug the power adapter into the IDU. The system may take as long as five minutes before being ready for a WiFi connection.

---

How do I connect to the Winegard® ConnecT™ WF1’s WiFi network?

Turn on your WiFi enabled device and scan for wireless networks. The label located on the front of the PDF or on the back of the IDU will display the default SSID and password. Select the WiFi signal and connect. Once the IDU has been selected, enter the password.

---

How do I access the Status Screen for the IDU?

Once connected to the Winegard® ConnecT™ WF1’s WiFi network, open an Internet browser and type 10.11.12.1 into the address bar and press Enter. Login using the username: admin and password: admin.

---

How do I scan for available WiFi networks?

On the main status screen, select SCAN FOR AVAILABLE WiFi to bring up a list of all WiFi signals in range. Select the desired network and click CONTINUE.

---

What should I do after selecting the desired network?

Enter the network password, if prompted. Once the Winegard ConnecT WF1 connects, open a new browser page, and the network will display a page confirming the connection. When INTERNET STATUS shows connected to the chosen network, the system is ready to browse.

---

What should I do if the network displays a “splash page” when connecting?

Some networks will display a “splash page” when connecting instead of using a network password. These pages will not always load on the web browser that you select but instead open on your devices default browser. Sometimes browsing to a web page will also bring up this splash page.

---

What should I expect on the initial setup?

On the initial setup, your ConnecT system may have to reconfigure the modem, which may cause an additional 1-2 minutes of delay before the ConnecT can be used. Do not click the back button on your web browser when navigating through this software.

---

What functions can I control from the Local Network Settings screen?

From the Local Network Settings screen, it is possible to change the network name, change the network password, and change the security type.

---

Why should I change my network name?

It is recommended that you change the name of your network, which will improve the security of your network and make it easier to find with your WiFi enabled devices.

---

How should I change the network password?

To secure your network, it is suggested that you change the network password to something you can remember. The new password must be eight characters long.

---

What is the default security type of the Winegard ConnecT WF1?

The Winegard ConnecT WF1 Security Type has been defaulted to WPA2-PSK (AES). Other options are available on this screen.

---

How do I set up a Guest Network?

To set up a Guest Network, click on ENABLE. Give the guest network an easily recognizable name. Enter a password. If you use a simple password, it is recommended that the guest network be disabled when not in use.

---

What information is displayed under “Connected Devices” in the Advanced Settings?

This displays the name of each device currently connected to the Winegard ConnecT WF1.

---

How do I change the Admin Password?

To change the ADMIN PASSWORD, click on CHANGE ADMIN PASSWORD to bring up the new password screen. Enter the new password into the area for both PASSWORD and RE-ENTER PASSWORD. The password in each of these boxes must match.

---

What should I keep in mind when changing the network SSID or password?

When changing the network SSID or password you will have to reconnect your device once the WF1 reboots.

---

How do I update the Winegard® ConnecT™ WF1 software from network?

From the Status Screen, choose UPDATE SOFTWARE from the drop down menu and click SELECT. Once on the update software screen, click CHECK FOR LATEST VERSION. If the check finds that you have older software, click PROCEED to update to the latest version. The system will be unavailable for several minutes while the IDU and ODU reset. As these power back on, the system will function normally.

---

How do I return to factory default SSID and password?

To return to factory default SSID and password, press the reset button located on the IDU for ten seconds. All changes will be lost and the unit will return to factory default SSID and password.

---

What maintenance should I perform on the ODU?

Periodically check the ODU to ensure all connections are tight.

---

Why doesn’t my system have a “Scan for WiFi” button?

One of two things is happening. Either you have logged into the system before the outdoor antenna has fully powered up, so please wait four to five minutes for the system to fully boot before logging in, or the Ethernet cable for the outdoor antenna is plugged into the Ethernet port on the indoor unit. Plug it into the port labeled “POE”.

---

The system says that it is connected, why won’t web pages load?

Some WiFi sources do not require a password to connect but do require something before they will let you use their network. In these cases, they will often have a “SPLASH” page that requires you to either agree to their rules or enter a password before they will allow you to use their network. These pages will not always load on the web browser that you select but instead open on your devices default browser. Sometimes browsing to a web page will also bring up this splash page.

---

The system keeps making me log in every time I try to change screens, what should I do?

Check to see if you have a second window open on the Winegard ConnecT status screen. Close this window and the problem should go away.

---

What should I do if I forget my password?

If you have not changed your default password, it will be listed on the back of the indoor unit. If you have changed this password, you can reset the unit using the RESET button on the bottom of your indoor unit. Press this button and your system will return to the factory settings. Once reset, the default password will unlock your system.

---

I changed my password and nothing happened, what could be the cause?

The Winegard ConnecT will reject any password that is not long enough. Try entering a password of at least eight characters.

---

What should I do if 10.11.12.1 does not bring up the login screen?

One of several things has happened. The first thing to check is the WiFi signal that your model is connected to. If this is not the Winegard ConnecT SSID, this address isn’t valid. If you are indeed connected to the correct network, the address may have been changed. To resolve this, press the reset button on the bottom of your indoor unit. This will return the unit to its factory settings.

---

My default SSID does not appear on my device when I search for it, why?

When the Winegard ConnecT first powers on or has reset for any reason, it stops broadcasting the SSID. It may take between four and five minutes from the time it regained power to start broadcasting again.

---

I changed my Winegard ConnecT SSID and was disconnected. Why?

This is normal. The old SSID that you were connected to is no longer valid, simply open your device’s WiFi screen and search for the name you chose for your network. Select this and enter the password.

---

I am connected to a network but the speed isn’t very good, why?

The Winegard ConnecT can only extend the signal range for what is available. Try moving closer to the source of the signal and logging on with your device directly. If the speed is still slow, try searching for another available network.

---

What do the LED lights on the Winegard ConnecT IDU indicate?

• Slow Orange Blink: The Winegard ConnecT IDU is searching for an ODU.
• Solid Orange: The Winegard ConnecT IDU has found an ODU and is supplying power. Waiting for a response from the ODU.
• Fast Orange Blink: The Winegard ConnecT IDU has received a response from the ODU and is waiting for a network connection.
• Slow Red Blink: The Winegard ConnecT IDU is connected by the PoE port to a device other than an ODU. Please connect the PoE port to the ODU only.
• Solid Green: The Winegard ConnecT IDU is connected to an ODU and has an internet connection available.
• Fast Green Blink: The Winegard ConnecT ODU is being updated with a new image.
• Alternating Green & Orange Blink: The Winegard ConnecT IDU is being updated with a new image.

---

What do the Status Screen messages indicate?

• Connected to Wifi XXXX: The Winegard ConnecT unit is communicating with the source WiFi signal and working. If you are unable to connect to the internet, the source signal may have a problem.
• Scanning: The Winegard ConnecT unit is looking for WiFi signals in range. This can take a few minutes. Once the unit is able to identify all of the signals, they will be listed and you will be able to choose one.
• Trying to Connect to Wifi XXXX: You have selected a source signal and the Winegard ConnecT unit is attempting to connect to this source. Once connected, the message should change to “Connect to…”.
• Logging into WiFi XXXX: The source signal is password protected. This message will be displayed after you have entered the correct password and the two systems work out the security protocols.
• Bad Password: The source signal is password protected. This message will be displayed after you have entered an incorrect password and the source system has rejected the connection. Generally, this screen will only be seen if the source signal is distant or weak. Normally, the password will be rejected on the network password screen.
• Not Connected: The Winegard ConnecT system is not connected to a network.
• Connecting to WiFi XXXX: The Winegard ConnecT system is talking to the selected source signal and a connection is being made. This will generally only take a minute or two.

---

What are the specifications of the Winegard® ConnecT™ WF1?

• Wireless Standard: 802.11a/b/g/n/ac.
• Frequency Band: 2.4GHz, 5GHz Simultaneous (5GHz indoor unit only).
• Wireless Speed (max): 2.4GHz: 450Mbps (Rx), 450Mbps (Tx); 5GHz: 1300Mbps (Rx), 1300Mbps (Tx).
• Amplifiers: Outdoor: (3) 2.4GHz amplifiers; Indoor: (3) 2.4GHz amplifiers, (3) 5GHz amplifiers.
• Wireless Security: WEP, WPA, WPA2, WPA mixed.
• Antennas: Outdoor: (3) Detachable high gain 5dBi antennas; Indoor: (3) Internal 2.4GHz 4dBi antennas, (3) Internal 5GHz 6dBi antennas.
• Ports: (1) RJ45 10/100/1000m Lan Port (IDU only); (1) RJ45 PoE (ODU & IDU); (2) USB 2.0 Ports.
• Power Rating: Switching, AC Input 100-240v, 1.5A.

---

What are the setup requirements for the Winegard® ConnecT™ WF1?

• Wireless 802.11a/b/g/n 2.4GHz network.
• Computer, tablet, or smartphone with a web browser.

---

What parts are included in the box?

• Outdoor 2.4ghz Antennas (3)
• Outdoor Unit (ODU)
• Indoor Unit (IDU)
• Power Adapter
• 25’ Ethernet Cable
• Indoor Unit Stand
• Mounting Feet w/Nuts (3)
• Mounting Screws (20)
• Outdoor Unit Cable Entry Cover w/Screw
• Cable Entry Plate
• Accessory Screws & Nuts (6 each) for optional accessory mounts