DIGI CONNECT SP (01) PDF MANUAL

Verify that you have all included equipment. If any item is missing or damaged, contact your supplier.

Included equipment:

– Digi Connect SP or Digi Connect Wi-SP

– Power supply

– Wi-Fi antenna (Wi-SP model only)

– Loopback plug

Required additional equipment:

– Ethernet cable (SP model only)

– Use a null modem for serial configuration

– A personal computer

1. Connect the power supply to the power connector.

2. Connect the Ethernet cable to the Ethernet port.

1. Connect the power supply to the power connector.

2. Connect the Wi-Fi antenna to the antenna connector.

1. Navigate to http://www.digi.com/products/serial-servers/wireless-serial-servers/digiconnectwisp, and click the Utilities link under the Product Support tab.

2. Select your operating system. A list of available utilities for your operating system appears.

3. Download and run either the Device Discovery Utility or Digi Port Authority – Remote.

Note: For Microsoft Windows operating systems, unzip the download package and run the executable. For Linux or UNIX operating systems, follow the instructions in the release notes.

If the serial ports for your product will be managed using Digi’s RealPort software, download the RealPort driver.

1. Navigate to http://www.digi.com/products/serial-servers/wireless-serial-servers/digiconnectwisp, and select Drivers under the Product Support tab.

2. Select your operating system. A list of available downloads and release notes for your operating system appears.

3. Download the RealPort driver and the release notes.

Note: For Microsoft Windows operating systems, unzip the download package and run the executable. For Linux or UNIX operating systems, follow the instructions in the release notes.

For additional support, download product support documentation.

1. Navigate to http://www.digi.com/products/serial-servers/wireless-serial-servers/digiconnectwisp.

2. Click the Product Support tab.

3. Navigate to the product documentation and other available resources as needed.

Use the Digi Discovery Utility or Digi Port Authority – Remote to discover devices on your network and open the web interface.

1. In the list of discovered devices, select the Digi Connect SP device.

2. Using the Digi Discovery Utility or Digi Port Authority, configure the IP address if necessary.

3. Open the Digi Connect SP web interface. In the Device Discovery Utility, click Open web interface. In Digi Port Authority-Remote, click Device Configuration.

4. A login prompt for the web interface appears. Enter the default username and password: root and dbps. Continue to section 5 (Configure DIP switches).

Use an access point preconfigured with the default SSID of CONNECT with no encryption and let the Digi Connect Wi-SP associate to it.

1. Once the device has associated, use the Digi Discovery Utility or Digi Port Authority – Remote to discover devices on your network and open the web interface.

2. In the list of discovered devices, select the Digi Connect Wi-SP device.

3. Using the Digi Discovery Utility or Digi Port Authority, configure the IP address if necessary.

4. Open the Digi Connect Wi-SP web interface. In the Device Discovery Utility, click Open web interface. In Digi Port Authority-Remote, click Device Configuration.

5. A login prompt for the web interface appears. Enter the default username and password: root and dbps.

6. From the web interface, you can then set a new SSID to match the intended production network’s SSID and security options.

7. Click Apply. The device will join that network on the next reboot.

Your Digi Connect Wi-SP device is now connected to the network and configured for basic network connectivity. Go to sections 5 (Configure DIP switches) and 6 (Connect the serial end device) to configure the serial port as needed.

This method requires a DB-9 null-modem cable and a serial terminal application on your computer, such as Hyperterm or PuTTY.

1. On the Digi Connect Wi-SP, set all four DIP switches to the up position.

2. Configure your serial terminal software to use the following serial settings:

baud rate = 9600 data bits = 8 stop bits = 1 parity = none flow control = none

3. Connect the null modem cable to the computer and the Digi Connect Wi-SP serial port.

4. A login prompt for the device appears. Enter the default username and password: root and dbps.

5. Enter the set wlan command to set the Wi-Fi interface parameters. For example:

#>set wlan channel=11 ssid=testssid authentication=wpa_psk encryption=ccmp psk=1234567890

Note: For a detailed description of the set wlan command, see the Digi Connect Family Command Reference. For a video guide to serial port configuration, see http://www.digi.com/videos/digi-connect-wi-sp-serial-port-configuration.

The device connects to the Wi-Fi network. You can further configure the device through the web interface. Use the Digi Discovery Utility or Digi Port Authority – Remote to discover devices on your network and open the web interface.

1. In the list of discovered devices, select the Digi Connect Wi-SP device.

2. Configure the IP address if necessary.

3. Open the Digi Connect Wi-SP web interface. In the Device Discovery Utility, click Open web interface. In Digi Port Authority-Remote, click Device Configuration.

4. A login prompt for the web interface appears. Enter the default username and password: root and dbps.

Your Digi Connect SP/Wi-SP device is now connected to the network and configured for basic network connectivity. Go to sections 5 (Configure DIP switches) and 6 (Connect the serial end device) to configure the serial port as needed.

Digi Connect SP and Digi Connect Wi-SP have a set of DIP switches on the underside of the device for setting the EIA mode for serial communications. Set these DIP switches according to your serial device requirements (EIA-232/422/485). See the table for the device server pinouts.

The DIP switch positions correspond to the following pin configurations:

DB-9 pin	ΕΙΑ-232 (All switches DOWN)	EIA-422/485 Full-duplex (Switches 1, 2 UP; 3, 4 DOWN)	EIA-485 Half-duplex (All switches UP)
1	DCD	CTS-	Not used
2	RxD	RxD+	RxD+
3	TxD	TxD+	TxD+
4	DTR	RTS-	Not used
5	GND	GND	GND
6	DSR	RxD-	RxD-
7	RTS	RTS+	Not used
8	CTS	CTS+	Not used
9	RI	TxD-	TxD-
Shell	GND	GND	GND

Note: If switch 4 is up, the termination resistor is connected. If the switch is down, the termination resistor is not connected.

1. Connect the serial end device to the serial port.

2. In the web interface, under Configuration, click Serial Ports. Configure serial port settings using port profiles. Port profiles are a defined set of serial port parameters for a particular use. The web interface and user guide contain descriptions of the port profiles. For Digi Connect SP/Wi-SP products, Digi recommends the RealPort profile. For help in configuring the device for use with other port profiles, see the Digi Connect Family and ConnectPort TS Family User Guide.

To configure ports to use the RealPort profile:

a. On the Serial Port Configuration page, click the port to be configured.

b. Click Change Profile.

c. In the list of profiles, select the RealPort profile.

d. Click Apply.

For additional cabling information, go to http://www.digi.com/products/serial-servers/wireless-serial-servers/digiconnectwisp and click the Cabling link under the Product Support tab.

Digi offers multiple technical support plans and service packages to help customers get the most out of their Digi product. For information on Technical Support plans and pricing, contact Digi at 877.912.3444 or visit http://www.digi.com/support.

To provide feedback on this document, send your comments to techcomm@digi.com.